燃料电池电动车车载甲醇重整器

对目前世界几大汽车公司研制开发的燃料电池电动汽车车载甲醇重整器加以介绍，着重讨论了重整器的设计与重整催化剂的布置。指出，甲醇重整器的效果良好，但重整器出口富氢重整气中CO的含量仍然很高，而较高浓度的CO会使燃料电池电极中毒。因此，从重整器中产生出来的重整气在进入燃料电池以前要进行净化。     

军用半挂汽车列车的现状和发展趋势

介绍了国内外军用半挂汽车列车的发展现状,根据军用半挂汽车列车的运载对象和使用环境,分析了其性能特点、关键技术和发展趋势.     

多点电喷天然气发动机燃料喷射过程研究

数值模拟了从电喷天然气发动机喷射阀喷出的非稳态喷流的发展过程，并由纹影实验验证了解析方法的可行性。采用数值模拟的方法考察了天然气喷流贯穿距离与喷射压力和喷孔数的关系；以及喷射阀质量流量与喷射压力和环境压力的关系；为精确地控制天然气燃料喷射量提供了理论依据。最后数值模拟了进气歧管内天然气喷流的发展过程，探明了天然气喷射对发动机工作过程可能造成的影响。     

Experimental evaluation of Heavy Duty Vehicle speed patterns in urban and port areas and estimation of their fuel consumption and exhaust emissions

Exhaust emissions and fuel consumption of Heavy Duty Vehicles (HDVs) in urban and port areas were evaluated through a dedicated investigation. The HDV fleet composition and traffic driving from highways to the maritime port of Genoa and crossing the city were analysed. Typical urban trips linking highway exits to port gates and HDV mission profiles within the port area were defined. A validation was performed through on-board instrumentation to record HDV instantaneous speeds in urban and port zones. A statistical procedure enabled the building-up of representative speed patterns. High contrasts and specific driving conditions were observed in the port area. Representative speed profiles were then used to simulate fuel consumption and emissions for HDVs, using the Passenger car and Heavy duty Emission Model (PHEM). Complementary estimations were derived from Copert and HBEFA methodologies, allowing the comparison of different calculation approaches and scales. Finally, PHEM was implemented to assess the performances of EGR or SCR systems for NO_X reduction in urban driving and at very low speeds.The method and results of the investigation are presented. Fuel consumption and pollutant emission estimation through different methodologies are discussed, as well as the necessity of characterizing very local driving conditions for appropriate assessment.     

Changes in fuel economy: An analysis of the Spanish car market

This paper estimates the role that technological change and car characteristics have played in the rate of fuel consumption of vehicles over time. Using data from the Spanish car market from 1988 to 2013, we estimate a reduced form equation that relates fuel consumption with a set of car characteristics. The results for the sales-weighted sample of vehicles show that energy efficiency would have improved by 30% and 42% for petrol and diesel cars respectively had car characteristics been held constant at 1988 values. However, the shift to bigger and more fuel-consuming cars reduced the gains from technological progress. Additionally, using the results of the fuel equation we show that, besides a natural growth rate of 1.1%, technological progress is affected by both the international price of oil and the adoption of mandatory emission standards. Moreover, according to our estimations, a 1% growth in GDP would modify car characteristics in such a way that fuel consumption would increase by around 0.23% for petrol cars and 0.35% for diesel cars.     

Influential vectors in fuel consumption by an urban bus operator: Bus route,driver behavior or vehicle type?

Energy costs account for an important share of the total costs of urban and suburban bus operators. The purpose of this paper is to expand empirical research on bus transit operation costs and identify the key factors that influence bus energy efficiency of the overall bus fleet of one operator and aid to the management of its resources.We estimate a set of multivariate regression models, using cross-section dataset of 488 bus drivers operating over 92 days in 2010, in 87 routes with different bus typologies, of a transit company operating in the Lisbon’s Metropolitan Area (LMA), Rodoviária de Lisboa, S.A.Our results confirm the existence of influential variables regarding energy efficiency and these are mainly: vehicle type, commercial speed, road grades over 5% and bus routes; and to a lesser extent driving events such as: sudden longitudinal decelerations and excessive engine rotation. The methodology proved to be useful for the bus operator as a decision-support tool for efficiency optimization purpose at the company level.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.     

Customizing driving cycles to support vehicle purchase and use decisions: Fuel economy estimation for alternative fuel vehicle users

Wider deployment of alternative fuel vehicles (AFVs) can help with increasing energy security and transitioning to clean vehicles. Ideally, adopters of AFVs are able to maintain the same level of mobility as users of conventional vehicles while reducing energy use and emissions. Greater knowledge of AFV benefits can support consumers’ vehicle purchase and use choices. The Environmental Protection Agency’s fuel economy ratings are a key source of potential benefits of using AFVs. However, the ratings are based on pre-designed and fixed driving cycles applied in laboratory conditions, neglecting the attributes of drivers and vehicle types. While the EPA ratings using pre-designed and fixed driving cycles may be unbiased they are not necessarily precise, owning to large variations in real-life driving. Thus, to better predict fuel economy for individual consumers targeting specific types of vehicles, it is important to find driving cycles that can better represent consumers’ real-world driving practices instead of using pre-designed standard driving cycles. This paper presents a methodology for customizing driving cycles to provide convincing fuel economy predictions that are based on drivers’ characteristics and contemporary real-world driving, along with validation efforts. The methodology takes into account current micro-driving practices in terms of maintaining speed, acceleration, braking, idling, etc., on trips. Specifically, using a large-scale driving data collected by in-vehicle Global Positioning System as part of a travel survey, a micro-trips (building block) library for California drivers is created using 54 million seconds of vehicle trajectories on more than 60,000 trips, made by 3000 drivers. To generate customized driving cycles, a new tool, known as Case Based System for Driving Cycle Design, is developed. These customized cycles can predict fuel economy more precisely for conventional vehicles vis-à-vis AFVs. This is based on a consumer’s similarity in terms of their own and geographical characteristics, with a sample of micro-trips from the case library. The AFV driving cycles, created from real-world driving data, show significant differences from conventional driving cycles currently in use. This further highlights the need to enhance current fuel economy estimations by using customized driving cycles, helping consumers make more informed vehicle purchase and use decisions.     

Multi-criteria optimization of traffic signals: Mobility,safety, and environment

Two-dimensional multi-objective optimizations have been used for decades for the problems in traffic engineering although only few times so far in the optimization of signal timings. While the other engineering and science disciplines have utilized visualization of 3-dimensional Pareto fronts in the optimization studies, we have not seen many of those concepts applied to traffic signal optimization problems. To bridge the gap in the existing knowledge this study presents a methodology where 3-dimensional Pareto Fronts of signal timings, which are expressed through mobility, (surrogate) safety, and environmental factors, are optimized by use of an evolutionary algorithm. The study uses a segment of 5 signalized intersections in West Valley City, Utah, to test signal timings which provide a balance between mobility, safety and environment. In addition, a set of previous developed signal timing scenarios, including some of the Connected Vehicle technologies such as GLOSA, were conducted to evaluate the quality of the 3-dimensional Pareto front solutions. The results show success of 3-dimensinal Pareto fronts moving towards optimality. The resulting signal timing plans do not show large differences between themselves but all improve on the signal timings from the field, significantly. The commonly used optimization of standard single-objective functions shows robust solutions. The new set of Connected Vehicle technologies also shows promising benefits, especially in the area of reducing inter-vehicular friction. The resulting timing plans from two optimization sets (constrained and unconstrained) show that environmental and safe signal timings coincide but somewhat contradict mobility. Further research is needed to apply similar concepts on a variety of networks and traffic conditions before generalizing findings.     

基于模糊层次的铁路混装货物装运安全评价研究

随着客户运输需求的多样化升级,采用铁路混装货物装运模式在提升铁路运输效率、吸引多样货源等方面相较于单一品名装运显示出一定的优越性,同时混装货物装运面临的安全压力相较于单一品名装运出现骤增。为保障铁路混装货物装运安全,在阐述混装货物装运特点及安全控制要点的基础上,从"人防""物防""技防"3方面构建混装货物装运安全评价指标体系,采用层次分析法确定各指标权重,并利用模糊综合评价法对铁路混装货物装运安全进行评价,通过实例验证该评价方法的实用性及有效性,为铁路混装货物装运安全评价提供依据。