HEV驱动系统的键合图建模和仿真计算

在深入研究某种混合动力汽车(HEV)驱动系统及其各单元动态特性的相互关系的基础上，运用键合图原理对该系统进行数学建模，并应用Matlab／Simulink进行仿真计算和研究。研究表明，所建模型较准确地反映HEV的动态特性，并发现由于多动力耦合中弹性与柔性耦合影响导致的载荷与运动波动，并证明调整阻尼可有效减小波动。     

基于ADVISOR2002混合动力汽车控制策略模块开发

介绍了混合动力汽车仿真软件ADVISOR中的并联控制策略，结合课题的实际情况，对ADVISOR2002的并联控制策略进行了二次开发，并针对某一车型进行了仿真对比，结果表明所提出的控制策略不仅能够鲁棒地在ADVISOR2002界面中运行，而且合理、可靠，满足实际需要。     

空气罐控制输液管道水击研究

采用特征线法对瞬时关闭管道终端阀门 ,在安装和不安装空气罐两种状况时 ,管道压力的变化情况进行了数值模拟 ,并分析了空气罐初始容积、空气罐安装位置等参数对管道瞬态水击压力变化的影响 ,结果表明 :在输液管道的适当位置安装容积一定的空气罐能较好地控制水击的产生     

Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

汽车操纵动力学十八自由度模型仿真研究

本文介绍了根据多刚体动力学中的凯恩方法建立的一般两轴汽车的十八自由度数学模型。     

汽车轮胎结构非线性有限元分析

本文综述了轮胎力学的发展历史与现状，阐明了轮胎结构分析的几各主要方法、研究内容及其优缺点，并重点介绍了在子午三维非线性有限元结构分析方面的工作，包括轮胎的充气，竖直加载、稳态滚动、滚动阻力及温度场分析，给出了相应的算例。由于采用一些新的方法和技术，考虑了更真实的轮胎材料模型，结构和载荷，使得分析更为有效、精确，分析结果可作为轮胎的设计，试验与改进的依据。     

国内外汽车碰撞计算机模拟研究的现状及趋势

本文论述和剖析了国内外利用计算机进行汽车碰撞模拟和建立汽车、乘员及汽车安全约束系统数学模型的研究进展。提出了我国开展汽车碰撞计算机模拟研究的发展趋势和应解决的问题。     

发动机冷却风扇温控液力驱动系统

本文介绍了发动机冷却风扇温控系统，这种新型的控制系统具有自动测量，微机控制，液压驱动，无级变速等特点，可以使发动机在最佳温度下工作，文中详细介绍了系统构成，测控元件选择及软件设计。     

大型汽车底盘动态模拟测功机测控系统

大型汽车底盘测功机的关键部分是行车阻力的精确模拟与控制。本文论述了大型汽车底盘测功机动态电模拟行车阻力系统的加载原理，组成与控制过程，通过实验证明其控制效果极佳，汽车加速过程与路面实际加速曲线贴合度误差不大于３％。     

汽车的力学参数与稳态转向特性

本文以汽车力学参数试验台测出的数据为基础，为通过建立轮胎侧偏角，车厢侧倾角，回正力矩与侧向加速度之间的关系，运用最小二乘法对测试数据进行线性曲线拟合，找出了这些数据与汽车记转向特性之间的关系，并按国家标准ＧＢ／Ｔ３０４７－９１中的有关规定对被测试车辆的稳态转向特性进行了评价 。