交通需求OD估计与预测的现状研究分析

目前，对于静态OD矩阵估计问题已经有很多研究者，对于动态OD前沿的研究工作则非常有限。关于对OD估计和预测的研究可分为封闭网络和开放网络。介绍了研究封闭网络的Bell，Van der Zijpp，Chang and Wu和Chang and Tao等人的方法，以及研究开放网络动态估计的3种方法，即Cascetta、Okutani、Ashok和Ben—Akiva等人的方法。并指出可以将OD估计问题陈述为具有不同误差特性、多个来源的不同类型信息的综合性和一致性的结合体，此联合估测就是经济计量学的混合估计的问题。     

日产VG30E发动机废气再循环系统的结构、工作原理及检修

日产VG30E发动机采用典型的电子控制废气再循环系统,其废气再循环系统的工作由微机集中控制系统(ECCS)根据相关传感器输入的信号进行控制。介绍了该系统的结构、工作原理及控制过程。在该系统的检修中,介绍了该系统工作情况的检查,控制阀的检修,电磁阀的检修,以及检修实例。     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

CDMA在视频监视系统中的应用

简单介绍码分多址(CDMA)的基本原理及性能;然后利用CDMA传输技术,设计一个无线视频图像传输系统。最后,介绍该系统的结构、基本原理以及在试验视频监视系统中的应用。     

基于ANN星识别算法的仿真平台

星敏感器是一种高精确度的姿态测量仪器，它通过对观测到的星点进行识别来计算姿态。为了能够较好地测试和验证星识别系统的性能，设计了一个基于ANN算法的星识别仿真平台。通过对该星识别仿真平台性能的测试，表明该仿真平台能够方便，实时地测试星识别算法的性能与正确性，因此说它是一种具有较好实用价值的星识别仿真平台。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Numerical simulation of the flow about self-propelling tanker models

A time-marching CFD simulation is performed for self-propelling ships. The flow about the hull is simulated by the finite-volume method, and the propeller action is approximated as a propeller disk for which the solution is given by a simplified propeller model. The interaction of two flow models is treated in a time-marching procedure converging towards the steady self-propelling condition. This method is applied to five tanker models, and detailed comparisons are made between the simulated results and corresponding experimental results. It is shown that the flow field in the self-propelling condition is qualitatively well reproduced in the simulation, and the estimated thrust deduction factors for the five hull forms agree well with measured ones. However, the effective wake factors are underestimated, since the Reynolds number in the simulations differs from that in the experiment.     

电压型逆变器输出电压检测与数字滤波方法研究

针对实时、准确地检测电压型逆变器输出电压基波比较困难的问题，从检测逆变器的直流支撑电压入手，提出了一种根据控制器的输出脉冲序列，利用ＤＳＰ进行实时计算逆变器输出电压基波瞬时输出值的新方案，试验结果证明了方案的可行性。     

采用折风板导流方式降低驾驶室后布置发动机温度

多田野７５２汽车起重机发动机型号为８ＤＣ８，近几年来一直存在发动机温度升高速度快，并持续不下的问题，致使发动机不能连续运行１～２小时，甚至经常需要停车降温，影响生产分析认为产生此问题的主要原因是：驾驶室阻挡减少了自然风，在现在的条件下，采用折风板，将驾驶室下部原来流失的自然风导入水箱前，迫使其通过水箱和发动机两侧，从而起的辅助冷却发动机的作用。