Experimental evaluation of Heavy Duty Vehicle speed patterns in urban and port areas and estimation of their fuel consumption and exhaust emissions

Exhaust emissions and fuel consumption of Heavy Duty Vehicles (HDVs) in urban and port areas were evaluated through a dedicated investigation. The HDV fleet composition and traffic driving from highways to the maritime port of Genoa and crossing the city were analysed. Typical urban trips linking highway exits to port gates and HDV mission profiles within the port area were defined. A validation was performed through on-board instrumentation to record HDV instantaneous speeds in urban and port zones. A statistical procedure enabled the building-up of representative speed patterns. High contrasts and specific driving conditions were observed in the port area. Representative speed profiles were then used to simulate fuel consumption and emissions for HDVs, using the Passenger car and Heavy duty Emission Model (PHEM). Complementary estimations were derived from Copert and HBEFA methodologies, allowing the comparison of different calculation approaches and scales. Finally, PHEM was implemented to assess the performances of EGR or SCR systems for NO_X reduction in urban driving and at very low speeds.The method and results of the investigation are presented. Fuel consumption and pollutant emission estimation through different methodologies are discussed, as well as the necessity of characterizing very local driving conditions for appropriate assessment.     

刚构桥0#块混凝土水化热温度场改值模拟分析

文章结合罗天乐连续刚构桥施工实例，运用有限元模型对该桥0#块混凝土浇筑施工过程中的温度场变化情况进行了数值模拟分析。结果表明，0#块混凝土内部最高温度及最大内外温差计算值与实测值吻合较好。     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

超深振捣条件下混凝土墙体模板侧压力的简化计算方法

超深振捣对混凝土成品质量有害无益,研究超深振捣引起模板侧压力增大的规律,可为规避其害提供依据。为此设计4个混凝土墙体试件,实测在浇筑过程中模板侧压力的变化情况。基于振捣液化和液体压力平衡理论,建立了超深振捣情况下混凝土模板侧压力计算模型,推导了计算公式,并与实验数据进行对比验证。研究结果表明,振捣深度是影响混凝土墙体模板侧压力的重要因素,本文提出的计算模型能很好地预测墙体结构超深振捣位置的模板侧压力。     

西南红层软岩地区铁路滑坡形成机理分析及治理措施

红层软岩地区铁路工程建设中滑坡问题突出。本文结合西南地区一铁路红层滑坡治理工程,利用该地区红层滑坡的现场调查结果,从红层软岩特性、地层岩性、地质地貌、水文地质条件、深孔位移监测数据等多方面对该地区铁路滑坡形成机理进行分析,并论述红层滑坡与一般滑坡的不同点,分析红层软岩岩体力学特性、地层主要成分以及红层软岩中的粉砂质泥岩在不同风化程度下的力学特性。根据分析结果提出治理措施,并对治理措施进行评价。总结得出地层岩性、地质水文、人为因素是导致红层滑坡病害发生的主要因素。     

Changes in fuel economy: An analysis of the Spanish car market

This paper estimates the role that technological change and car characteristics have played in the rate of fuel consumption of vehicles over time. Using data from the Spanish car market from 1988 to 2013, we estimate a reduced form equation that relates fuel consumption with a set of car characteristics. The results for the sales-weighted sample of vehicles show that energy efficiency would have improved by 30% and 42% for petrol and diesel cars respectively had car characteristics been held constant at 1988 values. However, the shift to bigger and more fuel-consuming cars reduced the gains from technological progress. Additionally, using the results of the fuel equation we show that, besides a natural growth rate of 1.1%, technological progress is affected by both the international price of oil and the adoption of mandatory emission standards. Moreover, according to our estimations, a 1% growth in GDP would modify car characteristics in such a way that fuel consumption would increase by around 0.23% for petrol cars and 0.35% for diesel cars.     

格拉斯磁环匀强磁场分析

以毕奥-萨伐尔定律为基础,建立亥姆霍兹线圈以及格拉斯磁环中心磁场分布模型,并计算了它们内部的轴向磁感应强度分布,绘出了空间分布图,分析了轴向磁感应强度与x、y坐标的关系,分析结果得到了亥姆霍兹线圈和格拉斯磁环内部匀强磁场分布区域,通过比较得到格拉斯磁环内部的匀强磁场区域比亥姆霍兹线圈内部的匀强磁场分布区域更大的结论。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

Influential vectors in fuel consumption by an urban bus operator: Bus route,driver behavior or vehicle type?

Energy costs account for an important share of the total costs of urban and suburban bus operators. The purpose of this paper is to expand empirical research on bus transit operation costs and identify the key factors that influence bus energy efficiency of the overall bus fleet of one operator and aid to the management of its resources.We estimate a set of multivariate regression models, using cross-section dataset of 488 bus drivers operating over 92 days in 2010, in 87 routes with different bus typologies, of a transit company operating in the Lisbon’s Metropolitan Area (LMA), Rodoviária de Lisboa, S.A.Our results confirm the existence of influential variables regarding energy efficiency and these are mainly: vehicle type, commercial speed, road grades over 5% and bus routes; and to a lesser extent driving events such as: sudden longitudinal decelerations and excessive engine rotation. The methodology proved to be useful for the bus operator as a decision-support tool for efficiency optimization purpose at the company level.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.