客车行业的市场现状及政策趋势

分析客车行业的市场现状及政策趋势；对客车行业应重点关注节能和安全标准的实施进行阐述。     

船舶应急电系统受控的逻辑关系

为加强轮机人员对电力系统知识的掌握,根据现代大型集装箱船电力系统的特点,详细介绍了船舶应急电系统受控的逻辑关系,特别指出联络开关的意义和作用,可为船舶电站设计、轮机设备维护管理及故障分析提供指导。     

以太网技术在列车通信网络中的应用探讨

基于现有列车通信网络(TCN)不能完全满足信息传输的情况,提出了工业以太网和CAN总线共存的方案,介绍了基于高性能数字信号处理器TMS320F206的工业Ethernet的硬件接口电路、CAN/Ethernet网关模型等。     

基于CarSim自适应巡航控制建模与仿真

文章首先利用模糊法则建立能够反映驾驶员反应时间的隶属度函数,并根据制动过程理论建立安全距离模型,通过安全距离模型建立期望加速度模型。然后分别建立加速和制动模型,在此基础上制定控制模式转换策略,基于PID算法设计巡航控制器。最后在Matlab/Simulink和CarSim联合仿真环境中验证所设计的控制系统的有效性。     

基于运输效益的城市公交发车频率

公交车发车频率的确定是公交运营调度的主要内容。受车站附近其他公交车的影响，乘客在各站点的可接受公交车容量和等车时间是不相等的；平均可接受公交车容量是乘客心理容量的平均值，如果车内乘客数量超过该容量，则采用容量向量来解释乘客上车过程。文中以运营利润最大化为目标函数，在车辆资源有限的情况下建立分析模型，应用遗传算法求解最大利润下的最优发车频率，并运用实例验证了所提出的方法。     

国内外混合动力客车动力总成方案此较研究

简要介绍混合动力客车动力总成方案分类，重点介绍国内、外典型的混合动力客车动力总成方案；通过对国内、外方案动力总成方案的比较，提出推广我国混合动力客车的建议。     

HD469单级减速驱动中桥总成失效分析

汽车实际运行中零件失效的表现往往较复杂,给失效分析工作带来很大的困难。本文结合HD469单级减速驱动中桥的失效,通过对拆开的桥的各个零件,尤其是出现异常零件的观察,运用系统推理分析思想,发现安装在差壳周圈上12.9级六角头螺栓掉头断裂是导致整个469单级桥总成发生严重失效的根本原因。     

客车转向垂臂的设计与校核

介绍客车转向系统传动机构中的转向垂臂的设计与校核,并给出范例。     

A novel fuzzy logic correctional algorithm for traction control systems on uneven low-friction road conditions

The traction control system (TCS) might prevent excessive skid of the driving wheels so as to enhance the driving performance and direction stability of the vehicle. But if driven on an uneven low-friction road, the vehicle body often vibrates severely due to the drastic fluctuations of driving wheels, and then the vehicle comfort might be reduced greatly. The vibrations could be hardly removed with traditional drive-slip control logic of the TCS. In this paper, a novel fuzzy logic controller has been brought forward, in which the vibration signals of the driving wheels are adopted as new controlled variables, and then the engine torque and the active brake pressure might be coordinately re-adjusted besides the basic logic of a traditional TCS. In the proposed controller, an adjustable engine torque and pressure compensation loop are adopted to constrain the drastic vehicle vibration. Thus, the wheel driving slips and the vibration degrees might be adjusted synchronously and effectively. The simulation results and the real vehicle tests validated that the proposed algorithm is effective and adaptable for a complicated uneven low-friction road.     

The effects of wheelset driving system suspension parameters on the re-adhesion performance of locomotives

In this study, in order to examine the effects of a wheelset driving system suspension parameters on the re-adhesion performance of locomotives, the stick–slip vibration was analysed according to theoretical and simulation analysis. The decrease of the slip rate vibration amplitude improved the stability of the stick–slip vibration and the re-adhesion performance of locomotives. Increasing the longitudinal guide stiffness of the wheelset and the motor suspension stiffness were proposed as effective measures to improve the re-adhesion performance of locomotives. These results showed that the dynamic slip rate was inversely proportional to the series result of the square root of the longitudinal guide and motor suspension stiffness. The larger the motor suspension stiffness was, the smaller the required longitudinal guidance stiffness was at the same re-adhesion time once the wheel slip occurred, and vice versa. The simulation results proved that the re-adhesion time of the locomotive was approximately proportional to amplitude of the dynamic slip rate. When the stick–slip vibration occurred, the rotary and the longitudinal vibrations of the wheelset were coupled, which was confirmed by train's field tests.