Assessment of the volume of fluid method for free-surface wave flow

This study was concerned with the free-surface wave flow around a surface-piercing foil. The volume of fluid method implemented in a Navier–Stokes computational fluid dynamics code was employed. Three widely used discretization schemes for the volume of fluid method were assessed for a test case that involved general ship waves, spilling breaking waves in front of the leading edge, and bubbly free surfaces in separated regions. A single computational approach was selected for the comparison, and a grid-dependence study was carried out. The computational results were validated against existing experimental data, showing good agreement. The validation results suggest that all three discretization schemes perform well, but the best and most efficient results were obtained using the high-resolution interface capturing scheme.     

低动力作用货车转向架动力性能的研究

本文探讨低动力作用货车转向架的原理及其动力性能的计算和评估方法。首先定义9项指标,作为衡量车辆对轨道动力作用的标准。然后研究这些指标的诸因素。在此基础上总结出实现低动力作用的基本途径。本文还应用这些研究成果,提出4种低动力作用货车转向架的设计方案,并通过数值计算,同国内、外主型货车转向架对比,从而论证其在我国铁路采用的可行性。     

A substitute model of two-dimensional dry friction exposed to dither generated by rolling contact of wheel and rail

Dither generated by rolling contact of wheel and rail smoothes dry friction damping provided by the primary suspension dampers of freight wagons and it should be taken into account in numerical simulations. But numerically the problem is non-smooth and this leads to long execution time during simulation, especially when the vehicle with friction dampers is modelled in the environment of an multi-body system simulation program, whose solver has to cope with many strong non-linearities. The other difficulty is the necessity of handling within the code a number of big volume files of recorded dither sampled with high frequency. To avoid these difficulties, a substitute model of two-dimensional dry friction exposed to dither is proposed that does not need application of dither during simulation, but it behaves as if dither were applied. Due to this property of the model, the excitation of the vehicle model by track irregularities may be supplied as low-frequency input, which allows fast execution and, the necessity of handling high-volume files of recorded dither is avoided. The substitute model is numerically effective. To identify parameters of the substitute model, a pre-processing employing a sample of the realistic dither is carried-out on a simple two-degrees-of-freedom system. The substitute model is anisotropic, describing anisotropic properties of the two-dimensional friction arising in the presence of one-dimensional dither. The model may be applied in other branches of engineering, for example, in mechatronics and robotics, where application of dither may improve the accuracy of positioning devices.     

浅谈沥青混合料路面接缝的施工方法

根据施工经验介绍了沥青混合料路面接缝的施工方法.     

Roll- and pitch-plane coupled hydro-pneumatic suspension

Passive fluidically coupled suspensions have been considered to offer a promising alternative solution to the challenging design of a vehicle suspension system. A theoretical foundation, however, has not been established for fluidically coupled suspension to facilitate its broad applications to various vehicles. The first part of this study investigates the fundamental issues related to feasibility and properties of the passive, full-vehicle interconnected, hydro-pneumatic suspension configurations using both analytical and simulation techniques. Layouts of various interconnected suspension configurations are illustrated based on two novel hydro-pneumatic suspension strut designs, both of which provide a compact design with a considerably large effective working area. A simplified measure, vehicle property index, is proposed to permit a preliminary evaluation of different interconnected suspension configurations using qualitative scaling of the bounce-, roll-, pitch- and warp-mode stiffness properties. Analytical formulations for the properties of unconnected and three selected X-coupled suspension configurations are derived, and simulation results are obtained to illustrate their relative stiffness and damping properties in the bounce, roll, pitch and warp modes. The superior design flexibility feature of the interconnected hydro-pneumatic suspension is also discussed through sensitivity analysis of a design parameter, namely the annular piston area of the strut. The results demonstrate that a full-vehicle interconnected hydro-pneumatic suspension could provide enhanced roll- and pitch-mode stiffness and damping, while retaining the soft bounce- and warp-mode properties. Such an interconnected suspension thus offers considerable potential in realising enhanced decoupling among the different suspension modes.     

沥青混凝土路面施工接缝的处理技术

在沥青混凝土路面施工中,接缝有纵向接缝和横向接缝(工作缝)两种。如果接缝处的平整度不好,会产生下洼或凸起。或因接缝处压实度不够和结合强度不足而产生裂纹,甚至松散。接缝处施工质量不理想的现象时常见到。在用宽幅摊铺机全幅摊铺面层的情况下,虽避免了纵向接缝,但横向接缝是不可避免的,至少每天会有一条工作缝。就此,对沥青混凝土路面施工中的接缝处理技术进行讨论。     

Multibody dynamics modelling of the freight train bogie system

Previous work in the railway technology laboratory at Virginia Polytechnic Institute and State University (Virginia Tech) focused on better capturing the dynamics of the friction wedge, modelled using three-dimensional rigid body dynamics with unilateral contact conditions. The current study extends the previous work to a half-bogie model treated as an application of multibody dynamics with unilateral contact to model the friction wedge interactions with the bolster and the sideframe. The half-bogie model was derived using MATLAB and functions as a three dimensional, dynamic, and multibody dynamics model comprised of four rigid bodies: a bolster, two friction wedges, and a sideframe assembly. This expanded model allows each wedge four degrees of freedom: vertical displacement, longitudinal displacement (between the bolster and sideframe), pitch (rotation around the lateral axis), and yaw (rotation around the vertical axis). The bolster and the sideframe are constrained to have only the vertical degree of freedom. The geometry of these bodies can be adjusted for various simulation scenarios. The bolster can be initialised with a pre-defined yaw (rotation around the vertical axis) and the sideframe may be initialised with a pre-defined pitch/toe (rotation around the lateral axis). The results of the multibody dynamics in half-bogie model simulation are shown in comparison with results from NUCARS^®, an industry standard in train-modelling software, for similar inputs.     

Simulation of dynamic interaction between train and railway turnout

Dynamic train–track interaction is more complex in railway turnouts (switches and crossings) than that in ordinary tangent or curved tracks. Multiple contacts between wheel and rail are common, and severe impact loads with broad frequency contents are induced, when nominal wheel–rail contact conditions are disturbed because of the continuous variation in rail profiles and the discontinuities in the crossing panel. The absence of transition curves at the entry and exit of the turnout, and the cant deficiency, leads to large wheel–rail contact forces and passenger discomfort when the train is switching into the turnout track. Two alternative multibody system (MBS) models of dynamic interaction between train and a standard turnout design are developed. The first model is derived using a commercial MBS software. The second model is based on a multibody dynamics formulation, which may account for the structural flexibility of train and track components (based on finite element models and coordinate reduction methods). The variation in rail profile is accounted for by sampling the cross-section of each rail at several positions along the turnout. Contact between the back of the wheel flange and the check rail, when the wheelset is steered through the crossing, is considered. Good agreement in results from the two models is observed when the track model is taken as rigid.     

Mathematical modelling of train–turnout interaction

The paper proposes a mathematical model of train–turnout interaction in the mid-frequency range (0–500 Hz). The model accounts for the effects of rail profile variation along the track and of local variation of track flexibility. The proposed approach is able to represent the condition of one wheel being simultaneously in contact with more than one rail, allowing the accurate prediction of the effect of wheels being transferred from one rail to another when passing over the switch toe and the crossing nose. Comprehensive results of train–turnout interaction during the negotiation of the main and the branch lines are presented, including the effect of wear of wheel/rail profiles and presence of track misalignment. In the final part of the paper, comparisons are performed between the results of numerical simulations and line measurements performed on two different turnouts for urban railway lines, showing a good agreement between experimental and numerical results.     

两种舰船—飞机耦合系统的降阶建模方法

舰船的运动和甲板的变形，对着舰飞机的冲击载荷会产生影响，而该冲击载荷又会直接影响飞行甲板的变形，因此两者的运动是耦合的，需要把它们作为一耦合系统进行分析。本文对该耦合系统提出了两种降阶建模方法。该方法首先对飞行甲板进行动力缩聚，使其只包含在整个降落过程中会与飞机起落架的运动发生耦合的所有自由度，然后把降阶了的模型与飞机一起建工耦合动力学方程。运用该方法建立起来的动力学方程规模将大大减小。通过对某型号飞机及舰船计算表明，本文提出的方法是可行的。