大型升船机卷筒与主轴连接技术

大型升船机承载能力大,若卷筒与主轴仍采用常规连接形式很难满足要求。分析了卷筒与主轴的各种连接结构,针对景洪升船机开发一种新的连接技术,解决了加工和装配的工艺难题。通过理论计算确定结构尺寸,成功完成了16件大型卷筒装置的设计生产加工。     

舵系锥轴锥孔连接受力分析

通过对船舶航行工况条件下锥面连接的受力分析,得出锥面连接的表面接触比压与其能传递的轴向摩擦力和摩擦扭矩关系的计算公式;并对压入安装工况条件下锥面连接的受力分析,得出装配时压入力与接触比压关系的计算公式。通过实例计算,证明该计算方法是可行的。     

履带式机械动力传动系统的故障诊断与排除

结合当前工程机械维修工作的实际情况,对主离合器、液力变矩器、驱动桥、转向离合器和转向制动器等部位的故障现象进行了深入的探讨.有针对性地提出了解决方案和具体措施,为检修提供了新的理念和方法.     

车用液力变矩器的变形仿真研究

为确保液力变矩器的使用安全，对液力变矩器（空壳）在同一离心力场下的不同油压作用进行了实际工况仿真和有限元分析，通过对实际车用液力变矩器空壳的试验测试，结果表明液力变矩器颈端（Hub)和柄端（Pilot)的轴向变形与油压呈线性关系，理论计算值与试验测试结果吻合较好。     

液力变矩器焊接的数值模拟和质量控制

对液力变矩器的制造精和质量要求很高，焊后必须保证产品的尺寸精度，并要进行疲 试验以考虑焊缝的强度。通过分析计算，可以预测各种条件对焊接变形的影响；发现疲劳承载时的最危险断面在不在焊缝处，而是在上盖板的弯角处。     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

液力变矩器反求设计与内流场数值计算

采用反求设计方法建立了液力变矩器三维模型.建立了液力变矩器涡轮内流场物理数学模型,利用Fluent软件进行了相应的数值计算.分析了涡轮流道内流体速度、压力及压力损失情况,阐述了流场形成机理,为液力变矩器优化设计提供了理论依据.     

基于数字信号处理的直接转矩控制研究

直接转矩控制因控制简单、具有优良的动静态特性，在电机控制中应用越来越广泛。但它在低速区的局限也较多。随着数字信号处（Digital Signal Processing，缩写DSP）技术的发展，使得改善其低速控制特性成为可能。文中简介了直棼转矩控制技术的特点、控制原理及难点，探讨了一种应用DSP技术的直接转矩控制方法。