按弹性支承计算板桥支点的荷载横向分布系数

介绍了配有橡胶支座的板桥．在对其荷载横向分布分析时。考虑支座为弹性体的这一客观因素．提出了计算板桥支点处荷载横向分布影响线的计算方法。由此法计算的荷载横向分布系数小于按直接布载法算得的结果。     

桥梁施工控制中高程测点模型系统误差的消除

为识别误差，将高程测量系统模型分为高程测量模型和高程测点模型。文中对预应力混凝土桥梁悬臂施工控制中主梁高程测点模型的系统误差进行详细分析．并通过采取合理措施进行消除。同时分析指出，施工规范中利用主梁顶面高程作为施工控制的质量标准。理论上可行。而实际获取的顶面高程结果可能无效。建议采用主梁底面高程作为施工控制的质量标准。     

鼓式制动器摩擦副压强不均匀性分析与评价

定义了鼓式制动器摩擦片压强的两种不均匀度指数，推导了现有的不同机构型式的鼓式制动器的摩擦副压强不均匀度指数的计算公式，并分析了其变化特性。以这两种压强不均匀度指数作为新的评价指标，对各种型式的鼓式制动器进行了评价，揭示了一些型式的鼓式制动器所固有的缺点。提出了改进传统鼓式制动器的技术方向和途径。     

轻型货车轮胎接地压力分布实测

利用自主开发的轮胎接地压力测试仪,进行了轻型货车不同花纹和不同使用年限轮胎,在不同轮胎胎压和不同负荷作用下,轮胎的接地压力分布规律测量。实测结果发现:轻型货车轮胎与路面的接触形状更接近于矩形;新胎比旧胎的接地压力要均匀些;轮胎胎压与平均接地压力、轮胎负荷与平均接地压力、轮胎负荷与有效接地面积基本上呈线性关系。     

江苏省交通事故时间分布分析

根据江苏省有关交通事故数据,利用统计方法对交通事故发生的时间特征进行分析。通过分析交通事故年时间分布规律的波峰曲线,得出江苏省交通事故发生数量开始振荡变化,逐年上升的势头有望于近期遏制。通过分析交通事故、月、周、小时时间分布曲线,得出交通事故高峰小时出现在交通量高峰小时之后的9~12h、14~16h,两者不重合。死亡高峰时段(危险时段)多发生在18~21h的3h内。研究结论对不同时间内如何采取不同的安全对策来降低江苏省交通事故具有指导作用。     

挂篮底模纵梁受力简化计算方法及承重分配系数

以一桥梁施工工程实例为依托,采用有限元软件ANSYS对桥梁悬臂施工中使用的菱形挂篮进行仿真分析.提出3种简化模式计算底模纵梁的承重分配,对比发现将底模纵梁承受的外荷载简化为集中荷载,并分配至挂篮下前后横梁的方法是最优简化计算方法.在此基础上对挂篮底模纵梁承重分配系数进行优化,从而简化了繁琐的挂篮底模纵梁受力分析计算,保证了挂篮结构设计和施工的安全.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

Travel time estimation from sparse floating car data with consistent path inference: A fixed point approach

Estimation of urban network link travel times from sparse floating car data (FCD) usually needs pre-processing, mainly map-matching and path inference for finding the most likely vehicle paths that are consistent with reported locations. Path inference requires a priori assumptions about link travel times; using unrealistic initial link travel times can bias the travel time estimation and subsequent identification of shortest paths. Thus, the combination of path inference and travel time estimation is a joint problem. This paper investigates the sensitivity of estimated travel times, and proposes a fixed point formulation of the simultaneous path inference and travel time estimation problem. The methodology is applied in a case study to estimate travel times from taxi FCD in Stockholm, Sweden. The results show that standard fixed point iterations converge quickly to a solution where input and output travel times are consistent. The solution is robust under different initial travel times assumptions and data sizes. Validation against actual path travel time measurements from the Google API and an instrumented vehicle deployed for this purpose shows that the fixed point algorithm improves shortest path finding. The results highlight the importance of the joint solution of the path inference and travel time estimation problem, in particular for accurate path finding and route optimization.     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。