The impact of structural flexibilities of wheelsets and rails on the hunting behaviour of a railway vehicle

The hunting motion of a passenger coach is investigated using a multibody system in which the wheelsets and the rails can be modelled as flexible bodies. By comparing the results for different model variants, in which the structural flexibilities of the wheelsets and of the rails are either taken into account or neglected, the impact of the flexibilities is analysed. It turns out that the flexibilities of both the wheelsets and the rails have a significant impact on the hunting behaviour by increasing the lateral motions of the wheelsets and lowering the critical speed. In order to investigate the impact of the flexibilities under different operating conditions, the calculations are carried out for track geometries using different rail profiles (60E1, 60E2) and different rail cants (1:40, 1:20) and for different values for the friction coefficient (0.25…0.4) at the wheel–rail contact. The results show that the influence of the flexibilities is the strongest for high lateral forces, which occur e.g. for contact geometries leading to high hunting frequencies and for high values of the friction coefficient. The results also show in some cases a strong impact of the flexibilities on the position of the wheel–rail contact on the running surface of the rail, which is of particular interest with respect to wear simulation.     

低动力作用货车转向架动力性能的研究

本文探讨低动力作用货车转向架的原理及其动力性能的计算和评估方法。首先定义9项指标,作为衡量车辆对轨道动力作用的标准。然后研究这些指标的诸因素。在此基础上总结出实现低动力作用的基本途径。本文还应用这些研究成果,提出4种低动力作用货车转向架的设计方案,并通过数值计算,同国内、外主型货车转向架对比,从而论证其在我国铁路采用的可行性。     

Tangential force variation due to the bogie direction reversal procedure

A range of tangential forces is generated within the contact patch when a wheelset moves on the rail. These forces are intensified when incorporating curved tracks and motored axle rail vehicles [Arrus, P., de Pater, A.D. and Meyers, P., 2002, The stationary motion of a one-axle vehicle along a circular curve with real rail and wheel profiles. Vehicle System Dynamics, 37(1), 29–58]. The wheelset is subject to flange contact if an unbalanced force remains in a curve towards the high rail gauge face. The resultant force in the transverse direction includes the lateral force, the radial force, and the creep forces in addition to the effect of the frequent wheelset displacement due to the kinematic oscillation [Iwnicki, S., 2003, Simulation of wheel–rail contact forces. Fatigue Fracture Engineering Material Structure, 26, 887–900]. This article has focused on a potential variation in some of the forces cited when the wheelset is subject to backward and forward movements. A severe wear rate observed within the wheel flange region in Iranian Railways was investigated by operating a test bogie on a curvaceous track. An obvious improvement in the wear rate and wear pattern of the wheels was attained when the second test bogie encountered a bogie direction reversal procedure. This enhancement is considered in this article from the force analysis standpoint.     

Influence of polygonal wear of railway wheels on the wheel set axle stress

The coupled vehicle/track dynamic model with the flexible wheel set was developed to investigate the effects of polygonal wear on the dynamic stresses of the wheel set axle. In the model, the railway vehicle was modelled by the rigid multibody dynamics. The wheel set was established by the finite element method to analyse the high-frequency oscillation and dynamic stress of wheel set axle induced by the polygonal wear based on the modal stress recovery method. The slab track model was taken into account in which the rail was described by the Timoshenko beam and the three-dimensional solid finite element was employed to establish the concrete slab. Furthermore, the modal superposition method was adopted to calculate the dynamic response of the track. The wheel/rail normal forces and the tangent forces were, respectively, determined by the Hertz nonlinear contact theory and the Shen–Hedrick–Elkins model. Using the coupled vehicle/track dynamic model, the dynamic stresses of wheel set axle with consideration of the ideal polygonal wear and measured polygonal wear were investigated. The results show that the amplitude of wheel/rail normal forces and the dynamic stress of wheel set axle increase as the vehicle speeds rise. Moreover, the impact loads induced by the polygonal wear could excite the resonance of wheel set axle. In the resonance region, the amplitude of the dynamic stress for the wheel set axle would increase considerably comparing with the normal conditions.     

斗轮式取料机行走位置精确定位

斗轮式取料机行走位置校正装置在定位中起到很重要的作用.分析了原有行走机构定位原理与状况.介绍了新定位装置的设计思路和实施方案,改革后提高了全场设备相互协同的效率和相互保护的可靠性.     

A passenger car driver model for higher lateral accelerations

Due to increasing demands for time and cost efficient vehicle and driver assistant systems development, numerical simulation of closed-loop manoeuvres becomes increasingly important. Thus, the driver has to be considered in the modelling. On the basis of a two-layer approach to model a driver's steering behaviour, the field of application is extended to higher lateral accelerations in this study. An analytical method to determine the driver parameters is presented, which is based on the two-wheel vehicle model. The simulation results are determined using a full vehicle model including all essential nonlinearities. Standard manoeuvres in the nonlinear range of vehicle handling behaviour are performed. A cornering manoeuvre is chosen to show the characteristics of the proposed driver model.     

汽车原地转向阻力矩经验公式的计算比较

本文通过对汽车静止转向状态下汽车转向阻力矩常用经验公式的分析,介绍了常用的转向系统设计时选用的转向阻力矩公式,并引入汽车在实际测量转向阻力矩的计算。在此基础上,将两者进行计算比较,画图,最后得出实际测量的原地转向阻力矩小于原地转向阻力矩经验公式,应该提出新的方法进行汽车静态下转向阻力矩的计算公式,指出了原地转向阻力矩计算方向。     

斯太尔汽车双前轴转向机构分析及其应用

本文在对斯太尔重型汽车的双轴转向传动机构进行分析的基础上建立了数学模型,研究了各部分的传动过程,并采用MATLAB语言编写了转向传动机构分析程序,对转向轴内外轮之间,前后轮间的转角匹配,以及最小转弯半径的匹配关系进行了优化。     

实现快速调整某转向前桥转向角

转向前桥在汽车上一个非常重要的功能就是实现汽车转向,而转向角是决定转向前桥性能的一个非常重要的参数,本文解决了在桥总成装配线快速调整某转向前桥转向角问题。     

Mathematical modelling of train–turnout interaction

The paper proposes a mathematical model of train–turnout interaction in the mid-frequency range (0–500 Hz). The model accounts for the effects of rail profile variation along the track and of local variation of track flexibility. The proposed approach is able to represent the condition of one wheel being simultaneously in contact with more than one rail, allowing the accurate prediction of the effect of wheels being transferred from one rail to another when passing over the switch toe and the crossing nose. Comprehensive results of train–turnout interaction during the negotiation of the main and the branch lines are presented, including the effect of wear of wheel/rail profiles and presence of track misalignment. In the final part of the paper, comparisons are performed between the results of numerical simulations and line measurements performed on two different turnouts for urban railway lines, showing a good agreement between experimental and numerical results.