无核密度仪在沥青路面离析无损检测中的应用

介绍了无核密度仪的测试原理,针对Superpave-25型沥青混合料,对无核密度仪基于不同测定样本容量的标定方法进行了比较分析,证明了提高测定样本容量标定的无核密度仪用于Superpave-25型沥青混凝土面层密度测定是可行和可靠的。同时,基于密度差的离析判别标准,采用无核密度仪评价沥青混凝土路面内部施工离析,并提出了控制施工离析的建议措施。     

土石混填路基压实度波动计算模型研究

为实现土石混填路基压实质量准确、快速检测,基于土石复合介质波动传播特性,导出了通过纵横波速综合反演土石混填路基压实度的波动计算模型.并以瞬态瑞雷波测试为手段对模型路基进行现场波动测试,采集波动数据,计算路基压实度.最后将压实度理论计算值与灌砂法测试结果作对比分析,验证该模型的可靠性.     

在役高桩码头桩基完整性无损检测技术研究的进展

一般情况下梁板式高桩码头的基桩顶部需要与上部结构嵌固,传统的单桩完整性检测方法已不能适用于此类基桩完整性的无损检测,在总结国内、外桩基检测研究成果的基础上,重点介绍对动测法和低应变反射波法的改进,主要包括双速度法、横波法、超震波法、纵阻抗剖面分析法等,分析论证在梁板式高桩码头基桩完整性检测中应用高应变法的可行性,以及综...     

船闸水工建筑物的检测与评估技术

采用现代测试技术及分析方法对船闸水工建筑物进行定期的检测评估可有效延长建筑物的使用寿命。提出了船闸水工建筑物检测与评估工作的一般流程,包括船闸现状的调查、检测方案的制定、现场检测的实施、检测报告的形成、评估单位的划分、复核验算的考虑因素、评估内容及方法及评估报告的形成,并就相关的检测与评估关键技术进行了阐述。     

软件测试中基路径获取方法的研究

软件测试是软件质量保证的重要手段,基路径测试是结构测试的一种重要方法.主要分析生成线性独立路径集合时,前后判定节点使用变量存在数据依赖关系的情况.借鉴程序切片技术中的转化理论,对数据控制依赖的判定节点在控制流图中进行修改;对一般的基路径获取步骤进行改进,可避免选择的路径不可达,提高基路径获取速率.实例表明它是有效的.     

公路工程试验检测数据处理问题探析

在公路工程的施工技术管理中,工程试验检测是一个重要环节,同时也是公路施工质量控制和工程竣工验收工作中不可或缺的一个关键步骤。针对这样一个关键环节,从数据表达和误差表示两个方面分析公路工程试验检测数据处理问题,可供参考借鉴。     

Investigation of active torsion bar actuator configurations to reduce vehicle body roll

The increasing popularity of sport utility/light-duty vehicles has prompted the investigation of active roll management systems to reduce vehicle body roll. To minimize vehicle body roll and improve passenger comfort, one emerging solution is an active torsion bar control system. The validation of automotive safety systems requires analytical evaluation and laboratory testing prior to implementation on an actual vehicle. In this article, a computer simulation tool and accompanying hardware-in-the-loop test environment are presented for active torsion bar systems to study component configurations and performance limits. The numerical simulation illustrates that the hydraulic cylinder extension limits the active torsion system’s ability to provide body roll angle reduction under various driving conditions. To compare the control system’s time constant and body roll minimization capabilities for different hydraulic valve assemblies and equivalent hose lengths, an experimental test stand was created. For a typical hydraulic pressure and hose diameter, the equivalent hose length was not a key design variable that impacted the system response time. However, the servo-valve offered a quicker transient response and smoother steady-state behavior than the solenoid poppet actuators that may increase occupant safety and comfort.     

Geometric design safety estimation based on tire–road side friction

A closed-loop drive–vehicle–road–environment system (DVRES) model was established using Adams/Car and Matlab/Simulink. Dynamic responses of lateral tire forces based on tire–road side friction and road geometric characteristics are used to investigate vehicle side slip for geometric design safety estimation. The root mean square, the maximum values of lateral tire forces, comfort limit on curves and vehicle trajectories are used to quantify the safety margin of side friction. The simulation results show that the safety margins of lateral tire forces for radius, operating speed and superelevation rate were 18.2%, 19.3% and 17.6%, respectively, to guarantee good vehicle lateral reliability and ride comfort, while lower speeds are optimal in wet and slippery roads. Finally, a case study was conducted to illustrate the analysis of road design safety, and on-site experiment testing further validated the accuracy and reliability of the closed-loop DVRES model.     

汽车车轮加速疲劳试验的研究

以累积损伤理论为基础，对汽车车轮加速疲劳试验进行了研究，以缩短试验时间，降低试验成本。     

某越野汽车制动管断裂原因探究

针对某越野车制动管经常断裂的故障，采用自功率谱密度、模态试验和数据统计方法，分析了影响制动管断裂的主要因素。认为从分动箱到前桥传动轴二阶振动是引起制动管断裂的关键因素。针对该因素介绍和讨论了几个有效的、快速和实用的解决方案：将前桥不等速十字轴式刚性万向节，更换为球笼式等速万向节；将与制动卡钳相连的制动钢管更换为一小段低膨胀、耐高压的软管。针对制动管断裂的原因，改变该车在石块路上进行可靠性试验考核制动管的试验规范，用高速行驶试验来考核制动管的可靠性。