履带式机械动力传动系统的故障诊断与排除

结合当前工程机械维修工作的实际情况,对主离合器、液力变矩器、驱动桥、转向离合器和转向制动器等部位的故障现象进行了深入的探讨.有针对性地提出了解决方案和具体措施,为检修提供了新的理念和方法.     

石方边坡控制爆破在公路路网工程中的运用

文章通过光面爆破与普通石方爆破的对比,总结石灰岩地区光面爆破各技术参数的选取和施工工艺的控制方法。     

车用液力变矩器的变形仿真研究

为确保液力变矩器的使用安全，对液力变矩器（空壳）在同一离心力场下的不同油压作用进行了实际工况仿真和有限元分析，通过对实际车用液力变矩器空壳的试验测试，结果表明液力变矩器颈端（Hub)和柄端（Pilot)的轴向变形与油压呈线性关系，理论计算值与试验测试结果吻合较好。     

液力变矩器焊接的数值模拟和质量控制

对液力变矩器的制造精和质量要求很高，焊后必须保证产品的尺寸精度，并要进行疲 试验以考虑焊缝的强度。通过分析计算，可以预测各种条件对焊接变形的影响；发现疲劳承载时的最危险断面在不在焊缝处，而是在上盖板的弯角处。     

曲轴滚压校直--计算机辅助修正技术的典型应用

计算机辅助修正技术是用于解决检测结果的量值与需要修正的量值之间没有确定的函数关系，甚至没有确定的实施修正作业方向的一些问题，对曲轴滚动压校直技术的原理、弯曲变形滚压校直的数学模型和工作机理加以详细介绍，并通过实例具体介绍了同轴滚压校直工艺的实现方法。     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

车载娱乐总成的静态电流分析

本文对车载娱乐总成的静态电流进行测试,找出其在室温、低温、高温下的分布规律,为车载娱乐总成生产厂家提供优化静态电流的思路。     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

舰船总段整体吊装研究和实施

对某型舰主船体采用船体三总段吊装,考虑舰船结构本身的复杂性,分别对各总段进行设计,包括重量、重心计算、吊点布置、结构及临时加强、强度校核等,吊装结果表明吊装工艺是合理的.