曲轴滚压校直--计算机辅助修正技术的典型应用

计算机辅助修正技术是用于解决检测结果的量值与需要修正的量值之间没有确定的函数关系，甚至没有确定的实施修正作业方向的一些问题，对曲轴滚动压校直技术的原理、弯曲变形滚压校直的数学模型和工作机理加以详细介绍，并通过实例具体介绍了同轴滚压校直工艺的实现方法。     

喷油泵装配线中拧紧技术的研究及应用

本论文介绍了拧紧技术的原理和方法,以及拧紧技术在喷油泵装配线中的应用.最后说明了拧紧程序在喷油泵装配线中的程序防错方法.     

盾构隧道管片接缝三元乙丙橡胶密封垫力学性能影响因素敏感度分析

为研究盾构隧道管片接缝三元乙丙橡胶密封垫力学性能的影响因素,首先,以实际工程为背景,采用自主设计的试验系统进行试验,并以此验证数值模型的可靠性; 然后,利用数值模型,采用正交分析方法,对密封垫断面参数(开孔形状、断面开槽数量、断面开孔率)、密封垫橡胶材料硬度、密封垫拼装姿态(张开量、错位量)进行六因素三水平的密封垫力学性能影响因素的敏感度分析; 最后,结合力学性能研究与防水性能预测需求,提出以闭合压缩力、密封垫接触应力分布作为分析指标。研究结果表明: 1)针对密封垫装配时所需的闭合压缩力,其影响因素主次顺序为张开量、断面开孔率、橡胶硬度、开槽数量、开孔形状、其他因素以及错位量; 2)密封垫接触应力分布的影响因素主次顺序为开孔形状、断面开孔率、错位量、其他因素、张开量、橡胶硬度、开槽数量。根据研究结果选取对密封垫力学性能影响较为显著的因素进行单因素分析,然后根据分析结果及橡胶垫密封垫防水性能预测方法, 提出背景工程管片接缝密封垫的优化方案。     

车载娱乐总成的静态电流分析

本文对车载娱乐总成的静态电流进行测试,找出其在室温、低温、高温下的分布规律,为车载娱乐总成生产厂家提供优化静态电流的思路。     

Observer-based clutch disengagement control during gear shift process of automated manual transmission

A clutch disengagement strategy is proposed for the shift control of automated manual transmissions. The control strategy is based on a drive shaft torque observer. With the estimated drive shaft torque, the clutch can be disengaged as fast as possible without large driveline oscillations, which contributes to the reduction of total shift time and shift shock. The proposed control strategy is tested on a complete powertrain simulation model. It is verified that the system is robust to the variations of driving conditions, such as vehicle mass and road grade. It is also demonstrated that the revised system with switched gain can provide satisfactory performance even under large estimation error of the engine torque.     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

舰船总段整体吊装研究和实施

对某型舰主船体采用船体三总段吊装,考虑舰船结构本身的复杂性,分别对各总段进行设计,包括重量、重心计算、吊点布置、结构及临时加强、强度校核等,吊装结果表明吊装工艺是合理的.     

液力变矩器反求设计与内流场数值计算

采用反求设计方法建立了液力变矩器三维模型.建立了液力变矩器涡轮内流场物理数学模型,利用Fluent软件进行了相应的数值计算.分析了涡轮流道内流体速度、压力及压力损失情况,阐述了流场形成机理,为液力变矩器优化设计提供了理论依据.     

基于参数自适应方法的路面性能衰变方程研究

路面性能衰变方程是针对路面在使用过程中性能衰变的预测。应用贝叶斯估计，对路面性能衰变方程的参数自适应进行了研究，得到参数自适应的计算公式。它能够简便的计算出模型所需的参数，不需通过对整体庞大的数据进行回归。最后通过随即生成的样本对提出的自适应算法进行了检验。     

基于数字信号处理的直接转矩控制研究

直接转矩控制因控制简单、具有优良的动静态特性，在电机控制中应用越来越广泛。但它在低速区的局限也较多。随着数字信号处（Digital Signal Processing，缩写DSP）技术的发展，使得改善其低速控制特性成为可能。文中简介了直棼转矩控制技术的特点、控制原理及难点，探讨了一种应用DSP技术的直接转矩控制方法。