基于轨道极限状态法的过渡板受力分析和配筋设计研究

京张高铁官厅水库特大桥为简支拱型大跨度钢桁梁桥,为防止梁端转角或错台量过大,降低梁端扣件系统受力,梁缝处设计采用了过渡板结构。为保证过渡板设计合理性和安全性,建立过渡板有限元实体模型进行受力分析,并首次运用轨道极限状态法对过渡板结构进行配筋设计。分析表明:(1)温度梯度作用对过渡板(420 mm厚)受力影响较大,在设计荷载中占据主导因素,在正温度梯度下,过渡板底部弯矩达到124.155 kN·m/m;(2)过渡板底部纵向弯矩在荷载基本组合作用下达到最大值,且实配配筋率最大,配筋时应注意以裂缝宽度为控制指标进行设计。     

激光熔覆涂层的组织特点与裂纹产生的机理探讨

碳钢、铸铁表面分别采用激光熔覆N i基、Fe基合金涂层,观察并分析了熔覆涂层界面及其显微组织和硬度特点,探讨了碳钢表面激光熔覆层裂纹产生的机理.     

平面一阶非线性椭圆型方程组的Riemann边值问题

本文研究平面非线性椭圆型方程组的Riemann边值问题:在假设条件(A1)、(A2)、(A3)之下,证明了该问题存在唯一的解1相似文献   

Preparation and Properties of Hydroxyethyl Methacrylate Chemically Modified Temperature-Sensitive Microgels

A novel series of poly (N-isopropylacrylamide-co-hydroxyethyl methacrytate) (p (NIPAM-co-HEMA))microgels were prepared through precipitation polymerization. Nuclear magnetic resonance (NMR), transmission electron microscopy (TEM), ultraviolet-visible spectroscopy (UV) and dynamic light scattering (DLS) were employed to characterize the microgels. The experimental results indicate that the prepared microgels with narrow distribution remain good temperature sensitivity after incorporation of functional -OH groups. In marked contrast to the general rule, incorporation of hydrophilic HEMA makes the volume-phase-transition temperature shift to the lower temperature due to the strong intermolecular H-bonding between amide and -OH groups, -OH and -OH groups.     

EFFECTIVE SHIELDING OF UNIDIRECTIONAL CURRENT GENERATED MAGNETIC FIELDS

Introduction　　 Environmentalelectromagnetic fields are ofin-creasing concern.Passive shielding is often em-ployed to reduce magnetic fields. Cylindricalshielding geometry is widely employed in powerin-dustry such as protective pipes,cable ducts andlightning down- conductors. Although shielding ef-fects of such conducting shells on magnetic fieldshave been recognized in recent decades,most ofthe studies have been devoted to the case of“dipole” ( opposite equal currents) sources or bal-anced…     

The Size Effects on Process Design of Micro Deep Drawing

This paper suggested to reformulate cylindrical deep drawing parameters with dimensionless form. A diagram, in which a feasible zone is drawn to bound both the maximal allowable tension and compression stress during the deep drawing process, was established. Since it is presented in a dimensionless form, it may be applied for both conventional and micro deep drawing. Cylindrical cup deep drawing was taken as an example to show the dimensionless process design method. In addition, the size effects should be taken into account. Two kinds of size effects on micro deep drawing were investigated, which can be explained by surface layer model and strain gradient model. Numerical simulations were carried out to compare the strain distribution with or without consideration of size effect.     

Geometrical design of blade＇s surface and boundary control of Navier-Stokes equations

In this article a new principle of geometric design for blade＇s surface of an impeller is provided. This is an optimal control problem for the boundary geometric shape of flow and the control variable is the surface of the blade. We give a minimal functional depending on the geometry of the blade＇s surface and such that the flow＇s loss achieves minimum. The existence of the solution of the optimal control problem is proved and the Euler-Lagrange equations for the surface of the blade are derived. In addition, under a new curvilinear coordinate system, the flow domain between the two blades becomes a fixed hexahedron, and the surface as a mapping from a bounded domain in R2 into R3 , is explicitly appearing in the objective functional. The Navier-Stokes equations, which include the mapping in their coefficients, can be computed by using operator splitting algorithm. Furthermore, derivatives of the solution of Navier- Stokes equations with respect to the mapping satisfy linearized Navier-Stokes equations which can be solved by using operator splitting algorithms too. Hence, a conjugate gradient method can be used to solve the optimal control problem.     

Investigation of Wall Pressure Fluctuations in a Turbulent Boundary Layer by Large Eddy Simulation

Large eddy simulation (LES) was used to investigate the space-time field of the low Mach number, fully developed turbulent boundary layer on a smooth, rigid flat plate. The wall-pressure field simulated by LES was analyzed to obtain the pressure statistics, including the wall-pressure root-mean square, skewness and flatness factors, which show the wall pressure distribution was not Gaussian. The profile of the auto-power spectral density and the contour of the streamwise wavenumber-frequency spectral density of wall-pressure were plotted. The "convection ridge" can be observed clearly and the convection velocity can be calculated from the location of the convection peak.     

第三方物流组织结构层次模型

组织结构是第三方物流企业运作高效的关键.基于流程的组织结构是第三方物流组织的发展趋势.文中结合流程的思想,从分工模式、协作关系和组织结构形态3个方面描述了第三方物流组织结构的特征,并提出了第三方物流组织结构层次模型,进行了分层描述.将模型应用于广州宝供物流企业集团有限公司的组织再造,并从定性的角度论述了新组织结构的优越性.     

二阶混合型积分微分差分方程的两点边值问题的存在性与唯一性

利用微分不等式技巧研究了某一类二阶混合型积分微分差分方程的两点边值问题,在上下解存在的条件下,得到了解的存在性和唯一性定理.结果表明:这种技巧为其它边值问题的研究提出了崭新的思路.