船舶电缆自动化敷设系统设计与实现

在船舶电缆敷设过程中,很难借助有效的工装提高劳动效率,低空间的高强度作业存在严重的安全风险。以船舶电缆自动化敷设系统为分析对象,介绍系统组成和系统接口,采用比例积分微分(Proportion Integration Differentiation,PID)算法计算系统行程,通过PROFINET总线完成数据传输,以人机界面(Human Machine Interface,HMI)实现系统性能要求。在风电安装平台上的实际运用表明,该系统可解决造船行业劳动力成本高和安全风险大的问题。     

基于隧道检测钢筋分布不均状况下判定衬砌结构安全性应用研究

近年来隧道内出现的越来越多的质量安全事故,引起各方高度重视,相应的最适宜隧道主体工程衬砌质量控制的地质雷达无损检测方法被广泛应用。通过雷达无损检测可揭露出衬砌内欠厚、脱空、钢筋分布不均等大量各类型缺陷,针对欠厚脱空等缺陷制定的注浆或开窗等治理措施是目前工程中常见的整改闭合工序,但钢筋分布不均对结构安全影响如何判定,怎么界定处理尚无成熟方案与规定。本文针对隧道项目中实际检测出的钢筋分布不均缺陷,在不宜大范围扰动结构及围岩进行整治的情况下,以及在避免其他问题共存等不利因素的前提下,应用有限元数值模拟计算分析强度安全系数,并结合现场外观等综合因素对衬砌结构安全性进行分析判定研究。     

桥梁单板受力的原因及预防措施探讨

从宏观角度分析桥梁预制板单板受力的一般规律,以及形成单板受力的原因,并从设计角度提出克服单板受力的措施,尤其是提出设置横向预应力是解决单板受力的有效措施,可供设计人员参考.     

浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

自锚式斜拉-悬索协作体系桥静风响应分析

自锚式斜拉-悬索协作体系桥作为一种全新的结构体系,兼备了自锚式悬索桥和斜拉桥的许多优点,结构体系则更为复杂。结合400m主跨的金州海湾大桥这一实际工程方案,建立了有限元空间分析模型,分析了其在静风荷载作用下的非线性行为,总结了初始攻角、附加攻角等参数及是否考虑缆索系统承受风荷载等对体系的影响规律。     

哈绕城高速公路东北段松花江大桥主桥设计方案研究

该松花江大桥为绕城高速公路东北段跨越松花江的一座特大桥,本文介绍了该桥三个桥型方案,并从结构受力、施工难易程度、耐久性、工程经济等方面进行比选提出推荐方案。     

基于虚拟应力场法的船舶避让与控制

为了实现船舶在航道内的避障,应用虚拟力场法建立了避障模型,描述了目标点的虚拟引力和障碍物的虚拟斥力之间的关系及其功能设计,实现了从船舶运动坐标值到控制量的转变,结果证明．船舶能够在多变的周边环境中实现避障功能。     

大倾角搁浅船舶扳正过程分析

在研究大倾角搁浅船舶的扳正过程中,计算了难船扳正力、横倾角和吃水。根据搁浅船舶的受力特点,建立了其力学模型,分析了扳正过程中横倾角、吃水、入泥深度与海底泥土性质对船体的影响。利用GHS软件模拟搁浅船舶的扳正过程,以某搁浅液化气船舶为例,求解了其扳正过程中船体扳正力、总搁坐力、剪力、弯矩和转矩,比较了难船不同扳正方案,分析了难船的扳正方式、搁坐位置、上层建筑与储气罐对难船打捞的影响。分析结果表明:在扳正过程中,3个方案的力学参数的变化趋势是一致的。最大扳正力相差较大,差值为9.1%~20.0%。搁坐力、剪力和弯矩均在横倾角为-55°~-50°时达到最大值,船体虽然在该阶段不需加载较大的扳正力,但仍应该注意船体的受力情况。在横倾角为-120°~-100°时,转矩变化非常剧烈。弯矩和转矩均出现了反向变化的现象,威胁船体结构的安全,扳正中应该谨慎处理。选择合适的扳正方案时应该综合考虑扳正力施力点的位置和扳正过程对船体与环境安全的潜在威胁。