Prediction of residual stresses induced by low transformation temperature weld wires and its validation using the contour method

Welding residual stresses are one of the main factors influencing the engineering properties of welded structures, and should be taken into account during designing and manufacturing products such as ships, bridges, etc. Recently, both computational and experimental methods play a significant role for providing residual stresses. The contour method (CM) became one of the most powerful techniques that can provide measurement of residual stresses normal to a plane of interest. In this method a component is cut at any plane of interest. Displacements normal to the cut surface are measured and then processed. Using the Thermal–Elastic–Plastic Finite Element Method (TEP-FEM), residual stresses after welding can be predicted. As well as, the elastic FEM can be used to reproduce residual stresses from measured longitudinal displacements in the CM.The main objective of this paper is to evaluate the effectiveness of different low transformation temperature (LTT) weld wires using TEP-FEM and the CM. In the simulation part, a computational approach is developed to numerically simulate both of welding and the CM. In the TEP-FEM, phase transformation is considered for LTT welds, additionally volume change and variation of mechanical properties with temperature are considered. In the simulated CM, welded specimens to be measured are replaced by TEP-FE models. Then the procedure of the CM is examined before applying it to real measurements. The simulated CM successfully predicted how the CM would reconstruct the residual stresses if applied experimentally. In the experimental part, welding is conducted using conventional and various LTT weld wires. Longitudinal residual stresses produced due to welding are measured using the CM. The results of TEP-FE simulation and the CM show the effectiveness of the different LTT weld wires in introducing compressive stresses in the weld. It is also observed that the applied LTT weld wires, which have almost the same martensitic transformation start temperatures, do not show big difference in the induced compressive residual stresses in the weld metal.     

论码头作业费纠纷的法律性质

有关码头作业费的纠纷在中国已经持续了四年多,自宣布收取该费用之日始,它就一直是航运界的热点问题。最近负责调查此事的有关部门作出了最终的调查结论,但并未对问题做出充分的解释和说明,以至于没能彻底解决班轮公会到底能否向货主收取码头作业费这一关键问题。本文试图通过对码头作业费纠纷法律性质的分析,为解决码头作业费的收取问题奠定基础。     

由The Washington Post Co．v．Totalnews Inc．案引发的法律问题

文章围绕被加框的网站加框行为进行分析后认为：被加框的网站不是—个演绎作品；本案中的加框行为构成了不正当竞争,简单的免责声明并不足以免责。在立法机关加强相关立法的同时,当事人各方技术上的“自助”会在一定程度上减少和避免纠纷。     

地铁区间中间风机房供电探讨

研究目的:探讨地铁地下区间中间风机房最优配电方案,保证事故情况下大功率隧道风机能可靠启动,把地铁事故危害降低到最小.研究结论:地铁地下区间中间风机房有功率90 kW风机两台,风机房总负载容量超过200 kW,且配电距离超过250 m的情况下,设计中一般采用高压配电方案.大功率风机选择软启动方式,可有效降低变压器低压侧的...     

煤矿斜井连续带式出渣机软起动方式优化研究

长距离斜井隧道施工所用连续带式出渣机,因其负载重且有一定的斜坡,在起动过程中驱动功率大、输送带张力大且变形量大。为优化其主要设计参数,以神华新街煤矿斜井长大隧道盾构施工所用连续带式出渣机为例,应用动态分析方法,通过建立连续带式出渣机离散动力学模型和动力学方程研究其最优起动方式。采用CST软起动系统并按照输入的加速度曲线起动,除正弦、抛物线、三角形和梯形4种常用起动加速度曲线外提出正弦组合曲线,运用Wilson-θ法进行方程求解,并使用Matlab进行动态仿真。结果表明,在5种不同的起动曲线仿真下,其设计参数都得到了优化,且采用正弦组合曲线起动得到的设计参数最优。该优化方法可降低连续带式出渣机的投资成本,可为类似项目设计提供参考。     

柴油发动机预热装置的控制原理及合理维护

详细介绍柴油发动机冷起动预热装置的作用、结构、原理和分类，着重分析预热时间的控制原理，最后提出合理维护起动预热装置的几项措施和注意事项。     

满足多台盾构始发要求的工作井结构设计研究

盾构工作井的尺寸应满足盾构机设备和安装的空间要求,对于需满足多台盾构下井拼装的情况,工作井的尺寸需考虑不同盾构机的尺寸及其交叉施工的影响。文中结合实际工程,分析多台盾构始发的结构尺寸要求,在满足结构尺寸要求的条件下对结构设计进行研究,通过工程验证,所提出的设计方法完全能满足结构功能要求。     

满足多台盾构始发要求的工作井结构设计研究

盾构工作井的尺寸应满足盾构机设备和安装的空间要求,对于需满足多台盾构下井拼装的情况,工作井的尺寸需考虑不同盾构机的尺寸及其交叉施工的影响。文中结合实际工程,分析多台盾构始发的结构尺寸要求,在满足结构尺寸要求的条件下对结构设计进行研究,通过工程验证,所提出的设计方法完全能满足结构功能要求。     

某MT车型无法启动和怠速启停失效问题分析

汽车的一键启动和怠速启停功能越来越普遍,本文结合某MT车型出现的无法启动及怠速启停失效问题的排查,阐述了开关防误触发的重要性,为后续主机厂对开关的布置提供参考。     

重度混合动力汽车燃油经济性和排放多目标优化

考虑重度混合动力汽车运行模式切换时发动机频繁起停对油耗的影响,建立了整车动态仿真模型和综合考虑燃油消耗和排放的多目标优化模型,采用简化控制变量的动态规划算法并结合自动变速器经济性换挡规律,在NEDC工况下对多目标优化模型进行仿真.结果表明,发动机的频繁起停对整车燃油消耗有显著影响,采用动态规划算法可全局优化整车燃油经济...