Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

第三轨供电系统中受流器与第三轨的接触压力及其对受流性能的影响分析

介绍了第三轨受流器的结构原理。分析比较了弹簧式和气压式受流器与第三轨接触压力调节方式的特点。基于电接触基本理论详细的阐述了受流滑板与第三轨接触区的导电机理。接触区域的导电电路由无数微小的电阻及电容并联而成,接触压力通过影响微小电阻、电容的数量比例,进而影响接触面上的导电能力和磨损性能。标称静态接触压力的设计值接近或等于"法向压应力临界值"时,导电能力和磨损特性取得均衡。     

铁路路基动态变形模量的数值模拟分析

介绍铁路路基动态变形模量理论计算公式的推导及动态变形模量的测试原理,采用有限元软件模拟动态变形模量的测试过程,分析承载板与土体接触压力、路基动态变形模量的影响因素,并计算动态变形模量的有效测试深度.结果表明:在承载板中心一定范围内,接触压力模拟结果较理论计算值大;土体的动弹性模量对接触压力影响很小,可以忽略;路基动态变形模量测试冲击荷载作用下,土体只发生弹性变形;动态变形模量与土体动弹性模量呈线性关系,路基动态变形模量的模拟结果大于理论计算值;土体的泊松比对动态变形模量影响较小;动态变形模量有效测试深度建议取0.5~0.6 m.     

计及移相角的多边形自耦变压器12脉波整流系统分析

多边形自耦变压器一定程度上减小了整流系统的体积,节约了变压器制造成本。为使多边形自耦变压器输出较大的二次侧电压值,优化多边形自耦变压器移相角,分析多边形自耦变压器移相角对12脉波整流系统输入侧电流谐波总畸变率,输出侧电压纹波系数,变压器、平衡电抗器、零序电流抑制器等效容量的影响;对比移相角在π/6、π/2时各个参数的值;提出适用于升压场合的多边形自耦变压器升压移相角;仿真实验验证了理论分析的正确性。同匝比时,多边形自耦变压器采用新移相角其输出电压幅值约为输入电压幅值1.4142倍,等效容量约为62.8%,较传统隔离式变压器等效容量小约37.2%。     

悬挂式单轨平面圆曲线乘客舒适度控制标准取值研究

乘客舒适度标准是确定线路平纵断面设计参数最为重要的控制指标,也是必须满足的强制性指标。为合理平衡乘客舒适度与工程建设成本之间的跷跷板关系,通过系统总结国内外各种现有制式取值标准,就悬挂式单轨乘客舒适度控制标准取值开展理论分析研究,并提出相应建议。与平面圆曲线半径相关的乘客舒适度指标为车体偏转角及未被平衡离心加速度,随着偏转角和未被平衡离心加速度数值的增加,其对最小圆曲线半径的影响逐渐减弱,恶化舒适度条件并不完全等同于工程效益的减小。悬挂式单轨最大偏转角理论上可突破传统轮轨铁路7.7°的限制,但增大偏转角对限界造成的影响不可忽略。人体可忍受的振动持续作用时间与未被平衡离心加速度大小成反比,将加速度控制在0.4～0.8 m/s~2是合理的。     

基于地基回弹因素的盾构隧道管片上浮预测

针对软弱地层盾构隧道管片脱出盾尾后出现的上浮问题,分析盾构施工过程中管片上浮的诱因,得出软弱地层中管片的上浮主要是地层应力重分布产生的地基回弹力引起的。在此基础上建立隧道开挖动态模型,分析隧道上浮量变化规律以及地层特性对管片上浮量的影响规律,得出地层弹性模量和管片上浮量呈一定的指数关系,且弹性模量对管片上浮量的影响远大于地层黏聚力和内摩擦角。通过力平衡理论计算盾构开挖引起的地层回弹力、管片上浮量以及隧道上浮影响的地层高度范围,并通过对珠江狮子洋工程管片上浮量的计算与实测对比,证明该公式的合理性,为盾构隧道工程中考虑地基抗力引起的管片上浮量预测提供一种新的方法。     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

����ʱ�չ켣���ٵĽ�ͨ�����Բ���������

基于视频的交通流检测在智能交通系统中具有重要意义。本文针对广泛采用的低位摄像机,提出了一种交通流特性参数的检测分析方法。首先基于三级虚拟检测线和自适应更新率局部背景建模来快速提取车辆特征点并消除活动阴影对提取精度的影响;然后基于Adaboost（Adaptive Boosting,自适应增强）分类器实现特征点按车分组,并在跟踪过程中根据运动特征相关度消除分组误差,获取高精度的车辆轨迹;进而自动生成多车道轨迹时空图并提取各车道交通流的多种特性参数。实验结果验证了算法的高效性;同时,自动生成的多车道轨迹时空图也为更多的交通信息获取和更深入的交通流特性分析提供了有力支持。     

基于VDI2230-2003标准的动车组车钩联接螺栓强度分析

使用ANSYS软件对某车钩安装座及其联接螺栓进行接触非线性静强度计算,在此基础上基于德国《VDI2230-2003螺栓强度校核标准》对螺栓进行强度评估,并和传统《机械设计手册》计算的结果进行比较,得出两种方法的计算值均满足强度要求,同时前者计算的轴向拉应力水平为后者计算的应力水平的72%,但剪切应力两者相同.     

抽气式涡轮帆的气动力学分析研究

介绍了抽气式涡轮帆的结构和工作原理,使用Gambit软件建立了涡轮帆的模型,并采用RNG k-ε湍流模型描述了涡轮帆的动力学特性。利用Fluent软件对抽气式涡轮帆进行了数值模拟计算,并与风洞试验数据进行了对比,升阻力系数的模拟结果与试验数据变化趋势基本一致。计算了特定情况下椭圆筒不同偏转角时的升阻力系数,并模拟了不同旋转角下吸气强度以及旋转角为0°时分流板位置对涡轮帆升阻力系数的影响,为涡轮帆的优化选择提供了依据。