悬索桥主缆线形的鞍座影响

提出了一个基于数值解析法的悬索桥主缆线形计算方法,能全面考虑各种鞍座影响,可用于成桥状态、空缆状态和施工阶段等各阶段的主缆线形分析。通过算例分析了鞍座对主缆线形的影响,计算表明,由于直接约束着主缆的变形,鞍座对主缆线形,特别是施工阶段的主缆线形有较大的影响。计算还表明,本文方法具有考虑因素全面、计算精度高、速度快、使用方便等优点。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

第三轨供电系统中受流器与第三轨的接触压力及其对受流性能的影响分析

介绍了第三轨受流器的结构原理。分析比较了弹簧式和气压式受流器与第三轨接触压力调节方式的特点。基于电接触基本理论详细的阐述了受流滑板与第三轨接触区的导电机理。接触区域的导电电路由无数微小的电阻及电容并联而成,接触压力通过影响微小电阻、电容的数量比例,进而影响接触面上的导电能力和磨损性能。标称静态接触压力的设计值接近或等于"法向压应力临界值"时,导电能力和磨损特性取得均衡。     

大直径盾构管片水平拼装试验方法探究

大直径盾构管片水平拼装试验存在效率低下甚至失败的情况,不能真实全面反映产品尺寸精度。分析其原因除大直径管片体积大、重量大的因素外,主要原因在于现有的试验设备工装简陋、试验方法粗放、规范要求低等。结合当前水平拼装的规范要求,分析现有试验方法存在的不足,对现有拼装设备工装进行改造,制定高标准的、更加严格的工艺措施,创造性地提出在每层管片拼装时增加标高检测的新思路。将新方法应用于南京长江第五大桥夹江隧道工程管片水平拼装试验,结果良好,证明了此试验方法的科学性与有效性。     

铁路路基动态变形模量的数值模拟分析

介绍铁路路基动态变形模量理论计算公式的推导及动态变形模量的测试原理,采用有限元软件模拟动态变形模量的测试过程,分析承载板与土体接触压力、路基动态变形模量的影响因素,并计算动态变形模量的有效测试深度.结果表明:在承载板中心一定范围内,接触压力模拟结果较理论计算值大;土体的动弹性模量对接触压力影响很小,可以忽略;路基动态变形模量测试冲击荷载作用下,土体只发生弹性变形;动态变形模量与土体动弹性模量呈线性关系,路基动态变形模量的模拟结果大于理论计算值;土体的泊松比对动态变形模量影响较小;动态变形模量有效测试深度建议取0.5~0.6 m.     

双块式轨枕外形质量快速检测系统研制及应用

SK?2型双块式混凝土轨枕是高速铁路无砟轨道结构中的重要预制件,单一生产厂日均产量达到800~1400根,但目前的人工检测方式无法满足双块式轨枕的出厂检验要求。本文提出的双块式轨枕外形质量快速检测系统可满足TB/T 3397—2015《CRTS双块式无砟轨道混凝土轨枕》的出厂检验要求,与双块式轨枕生产线相匹配,大大提高了检测效率,实现了双块式轨枕全参数、自动化、智能化检测。检测数据自动上传至生产管理平台,可对双块式轨枕生产质量进行跟踪管理。     

大断面异形盾构隧道弯矩传递系数原型加载试验研究

由于异形盾构隧道特殊的结构断面型式,管片设计暂无相关规范可循,故基于原型三环管片力学加载试验对异形盾构管片环向接头弯矩传递系数进行研究,研究结果表明:1)随埋深增加,异形盾构管片结构整体刚度提升,但由于各接头刚度与相邻管片结构刚度比随埋深增加变化规律不一致,异形盾构管片接头弯矩传递能力呈部分减弱部分增强的现象;2)同埋深条件下,随着侧压力系数的增加,除右拱腰处接头外,其余接头弯矩传递能力随着接头刚度与相邻管片结构刚度比的增大而逐渐增强;3)随着埋深增加,各接头弯矩传递能力对侧压力系数的敏感程度逐渐减弱;4)极限破坏后,异形盾构管片内外弧面裂缝的分布规律证明了明显的弯矩传递现象。     

The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

基于VDI2230-2003标准的动车组车钩联接螺栓强度分析

使用ANSYS软件对某车钩安装座及其联接螺栓进行接触非线性静强度计算,在此基础上基于德国《VDI2230-2003螺栓强度校核标准》对螺栓进行强度评估,并和传统《机械设计手册》计算的结果进行比较,得出两种方法的计算值均满足强度要求,同时前者计算的轴向拉应力水平为后者计算的应力水平的72%,但剪切应力两者相同.     

新型沙漏式FPSO的浮体外形参数对水动力性能的影响

为了解决传统船型和已有圆柱筒状FPSO的性能局限,论文提出了一种具有沙漏型浮式主体的新概念FPSO。根据所研发的新型沙漏式浮体模型,确定了能够反映浮体几何形状、FPSO基本功能和水动力性能的5个相互独立的外形参数。然后,采用基于频域势流理论的边界元数值模拟方法研究了新型沙漏式浮体在波浪中的运动响应,并且定性分析了不同浮体外形参数(下倾角、水线面半径等)对浮体水动力性能的影响,得到一些有意义的结论,以期能够为新型沙漏式FPSO的主浮体外形设计提供参考依据和准则。