炭纤维复合叠层铝板的制备工艺和实验研究

综合评论了从ＡＲＡＬＬ发展到新一代复合叠层铝合金板的进展。实验研究了新一代的叠层铝板－－炭纤维复合叠层铝板的制备工艺，并提供了所制备的炭纤维复合叠层铝板的性能。结果表明：这种铝板具有ＡＲＡＬＬ板的各种优点，能改进ＡＲＡＬＬ的一些缺点，它的各种性能指标皆优于铝合金板，因此可望取代高强度铝合金板而广泛应用于各类工程项目之中。     

船舶修理中对焊接设备的检查要求

在造船和修船的过程中由于电焊机和被焊件之间的连接不当,造成了电流对船体的腐蚀,严重时可能造成船体穿孔。对腐蚀和穿孔的原因进行电路分析,指出几种不正确的连接方法,同时给出正确的连接方法。     

防腐技术在海工钢筋混凝土结构中的应用

海工钢筋混凝土早期使用出现锈裂已成为沿海港口相当普遍的现象。通过工程实例 ,探讨了锈蚀的原因 ,提出了采取防腐措施对延长港口设施寿命的重要性 ,特别说明先于锈裂实施防腐 ,可大大降低后期的维修费用     

船体结构腐蚀疲劳问题以及数值计算方法

船体或者内部高强脆性材料在腐蚀环境中的破坏问题已受广泛关注,其中涉及破坏机理的研究屡见报道,但相关的数值计算研究方法目前还屈指可数,文章在介绍各种破坏机理的基础上,从数值计算方法研究的角度阐述了最近几十年中的研究进展以及作者在该领域所取得的前沿性的成果,并指出了无网格有限元计算方法将在这个研究领域扮演重要角色.     

碳钢、低合金钢全浸没海洋环境下最大点蚀深度简化模型

腐蚀是导致老龄船舶结构失效的主要原因之一。结合基本点蚀原理,文章对碳钢、低合金钢海水全浸没点蚀的主要影响因素、具体点蚀进程做了简要解释与评述。基于Melchers点蚀深度模型及其相关实验数据,文中提出一种简化形式的新型点蚀最大深度模型,并采用该模型对三组我国船舶结构常用碳钢、低合金钢的青岛海域全浸没点蚀试验观测数据进行分析。通过对比验证,证明采用Weibull函数表示点蚀最大深度随时间变化关系是合适的。此外,依据青岛、厦门、榆林海域碳钢试验数据,文中还对海水环境因素,如:溶解氧浓度、平均温度、盐度、PH值等,以及钢材成分变化对新型最大点蚀深度模型各参数的影响进行了初步探讨,得出了相应的函数关系式及相关结论。     

基于灰色马尔可夫理论的油气管道腐蚀剩余寿命预测

以灰色理论的标准GM（1,1）模型和马尔可夫TPM理论为基础,提出了基于灰色马尔可夫理论的油气管道腐蚀剩余寿命预测方法。利用灰色马尔可夫理论预测腐蚀油气管道剩余寿命的步骤主要包括：最大允许腐蚀深度的确定,腐蚀速率的预测以及剩余寿命预测。并基于该方法,采用VB系统开发了实用软件,简便可靠。该方法可以在腐蚀速率波动比较大的情况下预测油气管道的剩余寿命,为油气管道腐蚀检测周期的确定提供了科学依据。     

高速动力车不锈钢蒙皮焊接接头的耐蚀性能研究

本文对高速动力车车体1Cr18Ni9Ti不锈钢蒙皮焊接接头进行了耐晶间腐蚀研究，认为采用H1Cr18NiTi、HoCr19Ni12mO2O焊丝MIG、TIG焊均能有较子的耐腐蚀性能，但焊后热娇形对耐腐蚀性十分不利。     

浅谈杂散电流腐蚀机理及防护措施

详细阐述了地铁杂散电流的形成机理及主要的防护措施。     

Effect of pitting corrosion on local strength of hold frames of bulk carriers (2nd Report)—Lateral-distortional buckling and local face buckling

Pitting corrosion is typical corrosion observed on coated hold frames of bulk carriers which exclusively carry coal and iron ore. In order to secure the safety of these types of bulk carriers, it is important to understand the effect of pitting corrosion on local strength of hold frames.

In order to investigate this effect, a series of 4- and 3-point bend tests on structural models which consist of web, shell and face plates has been carried out. Artificial pitting was created on the web plate to simulate pitting. In the 4-point bend tests, two equal concentrated loads have been applied vertically at the one-third points of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, lateral-distortional buckling occurred before reaching the ultimate strength and local buckling of the face plate was observed after reaching the ultimate strength. The effect of web plate pitting on the lateral-distortional buckling strength was found to be small but the ultimate strength decreases with increase in the degree of pitting intensity. In the 3-point bend tests, concentrated load has been applied vertically at the center of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, local face buckling occurred just after reaching the ultimate strength. The ultimate strength is found to be decreasing with increase in the degree of pitting intensity.

A series of non-linear FE analyses has been performed to simulate the deformation behavior observed in the tests. It has been revealed that even in the case of randomly distributed pitting corrosion the ultimate strength of the structural models was almost the same as that of the structural models with uniform corrosion corresponding to the average thickness loss.     

水冷型艉轴的腐蚀形态及防护措施

艉轴是船舶的重要部件,其性能的好坏直接影响船舶动力装置性能的发挥和船舶的安全性,而腐蚀又是直接危害艉轴性能的主要因素。文章归纳了艉轴腐蚀易发生的部位及腐蚀形态,通过分析其腐蚀机理,提出了有效的防护措施。