高速铁路路基边坡纤维团粒喷播生态防护技术

针对高速铁路路基绿化工程高要求、少维护等特点,提出纤维团粒喷播技术,并详细阐述了其机理及特点.通过在京雄城际铁路路基边坡工程中的应用,归纳总结了该技术施工工艺流程:平整坡面→坡面覆土→铺设铁丝网→喷播基质→养护管理.喷播基质是利用喷播机械将性能优越的基质材料喷附至铁路路基坡面上的.工程应用表明该技术施工快,质量好,养护维修量小,经济性高.     

多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

A regression and beam theory based approach for fatigue assessment of containership structures including bending and torsion contributions

Container shipping has been expanding dramatically during the last decade. Due to their special structural characteristics, such as the wide breadth and large hatch openings, horizontal bending and torsion play an important role to the fatigue safety of containerships. In this study the fatigue contributions from vertical bending, horizontal bending and torsion are investigated using full-scale measurements of strain records on two containerships. Further, these contributions are compared to results from direct calculations where a nonlinear 3D panel method is used to compute wave loads in time domain. It is concluded that both bending and torsion have significant impacts on the fatigue assessment of containerships. The stresses caused by these loads could be correctly computed by full-ship finite element analysis. However, this requires large computational effort, since for fatigue assessment purposes the FE analysis needs to be carried out for all encountered sea states and operational conditions with sufficient time steps for each condition. In this paper, a new procedure is proposed to run the structure finite element analysis under only one sea condition for only a few time steps. Then, these results are used to obtain a relationship between wave loads and structural stresses through a linear regression analysis. This relation can be further used to compute stresses for arbitrary sea states and operational conditions using the computed wave loads (bending and torsion moments) as input. Based on this proposed method for structure stress analysis, an efficient procedure is formulated and found to be in very good agreement with the full-ship finite element analysis. In addition it is several orders of magnitude more time efficient for fatigue assessment of containership structures.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.     

A design method of tensile triangles and low transformation temperature weld metal for reduction of stress concentration and residual stress of welded joints

Stress concentration and residual stress have a significant influence on fatigue life of welded joints. In order to reduce the stress concentration of welded joints, a mathematical design method of tensile triangles (MTT) based on bionics was applied to weld shape design. Accordingly, the stress concentration of various weld beads in the corner boxing welded joint and the fillet welded T-joint was dissected using our in-house FEM software JWRIAN. It was found that there existed a large stress concentration in the conventional welded joints, whereas those welded joints with elongated weld bead were accompanied by a lower stress concentration, especially for elongated weld bead with MTT design. Furthermore, among the weld shapes of the corner boxing fillet welded joint, the rectangle shape of weld bead had the minimum stress concentration factor (1.05). For the fillet welded T-joint with MTT design, the stress concentration of weld toe decreased dramatically with the increase of the index of designed shape, but there was a minor difference of stress concentration at weld root between the weld beads with MTT design. In addition, application of low transformation temperature (LTT) weld metal utilizing martensitic transformation to the fillet welded T-joints can produce compressive residual stress at weld toe.     

长大货物车适应THDS轴温探测技术的研究

针对不适应THDS轴温探测系统的长大货物车,分析论证了现车轴箱改进方案适应THDS轴温探测的不足,并提出了轴箱优化方案。经计算、试验和装车验证表明,新轴箱可行、有效、安全,满足THDS轴温探测要求,保证了长大货物车运输安全。     

兰州地铁地温分布特性及其演化规律

以兰州地铁所在地区为研究对象,实测地铁隧道开挖前的地温(简称为初始地温),根据实测数据,提出地铁初始地温预测模型公式。采用非稳态传热的数值模型,分析运营条件下地铁隧道围岩温度的演化规律。结果表明:兰州地铁初始地温随环境气温和埋深的变化而变化;年变温层位于自地表至埋深12m处;年恒温层位于埋深12m及其以下,温度为15℃左右;年变温层中,1年内初始地温变化规律与环境气温变化规律相似,近似呈正弦曲线状分布,但存在相位滞后的现象;1年中初始地温的振幅随埋深的增大呈指数下降趋势。在隧道内空气与围岩之间热交换中,兰州地铁隧道围岩的温度及其梯度、热透厚度(未达到极限时)均与隧道内环境温度、热交换时间成正相关关系,但与距隧道内壁的距离成负相关关系。     

双块式轨枕外形质量快速检测系统研制及应用

SK?2型双块式混凝土轨枕是高速铁路无砟轨道结构中的重要预制件,单一生产厂日均产量达到800~1400根,但目前的人工检测方式无法满足双块式轨枕的出厂检验要求。本文提出的双块式轨枕外形质量快速检测系统可满足TB/T 3397—2015《CRTS双块式无砟轨道混凝土轨枕》的出厂检验要求,与双块式轨枕生产线相匹配,大大提高了检测效率,实现了双块式轨枕全参数、自动化、智能化检测。检测数据自动上传至生产管理平台,可对双块式轨枕生产质量进行跟踪管理。     

基于光纤传感系统的德国列车实时精确定位技术

实时、精确地获取列车位置信息是保证列车安全有效运行、发挥效率、提供最佳服务的前提。而轨旁传感器将在进行高效、可靠的列车跟踪和定位方面发挥重要作用。文章介绍德国基于光纤传感系统的列车实时精确定位技术,这是一种全新的解决方案,具有独特的优势和可能性。     

某型直流充电柜温度场仿真

对某型直流充电柜满负载工况下温度场进行仿真,根据实验测量数据验证仿真结果准确性,成功完成了对充电柜温度场的建模仿真工作,并实现对初始模型的简化,为对整个充电站进行温度场建模仿真奠定了基础。