共轨蓄压式电控喷油器的泄漏分析与试验

全面分析了共轨蓄压式电控喷油器的泄漏部位及影响因素,进行了静态和动态的密封性试验。试验结果验证了电控喷油器的设计精度与加工工艺的合理性。     

路段动态特征中的交通组成因素研究

基于对交通流建模过程中将车型单一考虑为标准小汽车,忽略了现实交通量中车型的不同构成,本文通过对不同车型的动力特性进行标定,将其特性反映在跟车模型与车道变换模型中,并且利用交通仿真技术,分析了交通量构成对路段行程时间、车速、延误等动态特性指标的影响。     

工程车辆FOPS冲击试验中落锤塑性变形研究

为了对工程车辆的落物保护装置(FOPS)进行可靠性试验提供理论依据,采用冲击动力学的塑性波两侧的动量平衡理论对工程车辆FOPS受冲击时落锤的动态响应进行了研究,建立了锤头变形的基本方程,绘制了方程相应曲线;建立了锤头在冲击过程中任一瞬时变形长度和非变形长度的数学模型,找到了工程应变和冲击速度之间的曲线对于塑性大变形的突变点及影响落锤变形的各个因素和控制变形的依据。为减小落锤的蘑菇形尺寸,降低锤头的材料成本,多次重复使用落锤,进行合理的落锤结构设计指明了方向。     

三轴汽车前后轮角输入时的响应特性

本文详细推导了三轴汽车线性二自由度模型的运动微分方程，分析了汽车对前后轮角输入时的移居记响应特性。从汽车动力学的角度讨论了前后轮转应具备的比例关系。该方法同样适用于其它多轴汽车的建模分析。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

Dynamic stride length adaptation according to utility and personal space

Pedestrians adjust both speed and stride length when they navigate difficult situations such as tight corners or dense crowds. They try to avoid collisions and to preserve their personal space. State-of-the-art pedestrian motion models automatically reduce speed in dense crowds simply because there is no space where the pedestrians could go. The stride length and its correct adaptation, however, are rarely considered. This leads to artefacts that impact macroscopic observation parameters such as densities in front of bottlenecks and, through this, flow. Hence modelling stride adaptation is important to increase the predictive power of pedestrian models. To achieve this we reformulate the problem as an optimisation problem on a disk around the pedestrian. Each pedestrian seeks the position that is most attractive in a sense of balanced goals between the search for targets, the need for individual space and the need to keep a distance from obstacles. The need for space is modelled according to findings from psychology defining zones around a person that, when invaded, cause unease. The result is a fully automatic adjustment that allows calibration through meaningful social parameters and that gives visually natural results with an excellent fit to measured experimental data.     

基于Prover的联锁软件形式化验证过程研究

计算机联锁系统是铁路信号控制系统的核心设备,是有着苛刻安全要求的复杂控制系统。本文采用Prover形式化开发工具对联锁软件安全需求进行形式化验证。通过模型检验的形式化验证方法,遍历系统输入变量的所有状态空间.验证联锁特定应用满足系统安全需求,确保系统的安全性得以正确实现。在保证系统安全性的基础上,以全状态空间查找反例的检验方法进一步提升产品的质量。     

STAAD.Pro在海洋工程模块吊装设计中的应用

对STAAD.Pro软件在海洋工程模块建造的加工设计阶段的应用进行了探讨。通过STAAD.Pro软件的可视化操作平台,对实际海洋工程模块进行建模、加载、计算和分析,通过计算得出模块的质量和质心位置,并根据规范对模块进行整体强度校核,从而对海洋工程模块的吊点布置及其吊装过程起到实际的指导作用。     

舰船加筋板局部强度评估中的总纵应力折减系数研究

舰船加强筋尺寸的合理确定一直是结构设计中的热点问题。本文综合考虑总纵弯曲应力和局部载荷的相互作用,研究加强筋的许用应力折减系数(C_s)的影响因素与合理取值方法。通过分析加强筋的力学模型、对比不同规范中的C_s取值,以及用非线性有限元软件Abaqus计算一系列加筋板模型,拟合C_s曲线并与规范对比,并验证剖面对称性和局部载荷作用方向对C_s取值的影响方式,丰富了舰船局部强度校核方法的技术背景,为板架设计、舰船三维局部校核程序开发提供借鉴。