试验动车组受电弓弓体及安装强度研究

为了解受电弓在我国高速试验动车组上的性能,对其机械、结构强度进行预判,构建了试验动车组受电弓弓体、底座的有限元分析模型,分析了600 km/h速度工况下,弓体各部件的机械结构强度参数、底座及焊缝关键部位的应力分布,并对弓体结构强度、底座焊缝结构强度、固定螺栓结构强度进行了校核。分析结果表明:试验动车组受电弓的弓体及安装结构强度均在安全系数范围内,能够满足试验列车高速运行的要求。     

螺栓强度分析方法研究

阐述了承受轴向载荷的螺栓联结的强度校核分析方法,并对相关步骤做了较为详细的介绍,可为工程结构整体设计和校核螺栓联结提供参考。     

锂离子动力电池在双能源机车上应用的可行性研究

文章介绍锂离子动力蓄电池在轨道交通领域的应用现状,重点研究锂离子蓄电池在新型双能源机车上应用的可行性和关键技术方案,明确了新能源机车研究的重要意义。     

Detection of nonlinearity effects in structural integrity monitoring methods for offshore jacket-type structures based on principal component analysis

The detection of changes in the dynamic behavior of structures is an important issue in structural safety assessment. The development of detection methods assumes greater significance in the case of offshore platforms because the inherent problems are compounded by the harsh environment. Here, we describe an instrumented physical model for the structural health monitoring of an offshore jacket-type structure and the results of tests in several different damage scenarios. In a comparative investigation of two different methods, we discuss the difficulties of implementing damage detection techniques for complex structures, such as offshore platforms. The combined algorithm of a fuzzy logic system and a model updating method are briefly discussed, and a method based on stochastic autoregressive moving average with exogenous input is adopted for the structure. The consideration of uncertainties and the effects of nonlinearity were major objectives. So, the methods were also investigated based on the test scenarios consisting of the physical model with a geometric nonlinearity. The principal component analysis method was utilized for the detection of nonlinearity in the recorded data. The results show that the developed methods are suitable for damage classification, but the quality of the acquired signals must be considered an important factor influencing successful classification. The development of these methods may be extremely useful, as such technologies could be applied for offshore platforms in service, enabling damage detection with fewer false alarms.     

Indirect method for wheel–rail force measurement and derailment evaluation

Wheel set flange derailment criteria for railway vehicles are derived and the influence of wheel–rail contact parameters is studied. An indirect method for wheel–rail force measurement based on these derailment evaluation criteria is proposed. Laboratory tests for the calibration of strain–force devices on the bearing box are carried out to determine the relationship between the applied force and the measured strain. The simulation package, SIMPACK, is used to develop a passenger car model to generate wheel–rail forces and vibration signals. Different cases are considered in this model to provide an accurate validation of the identified wheel–rail forces. A feasibility test is conducted in the Beijing Loop test line using a passenger car equipped with a set of strain gauges on the wheel set. The comparison of the force time history applied to the instrumented wheel set and that obtained using the indirect method is presented.     

计及移相角的多边形自耦变压器12脉波整流系统分析

多边形自耦变压器一定程度上减小了整流系统的体积,节约了变压器制造成本。为使多边形自耦变压器输出较大的二次侧电压值,优化多边形自耦变压器移相角,分析多边形自耦变压器移相角对12脉波整流系统输入侧电流谐波总畸变率,输出侧电压纹波系数,变压器、平衡电抗器、零序电流抑制器等效容量的影响;对比移相角在π/6、π/2时各个参数的值;提出适用于升压场合的多边形自耦变压器升压移相角;仿真实验验证了理论分析的正确性。同匝比时,多边形自耦变压器采用新移相角其输出电压幅值约为输入电压幅值1.4142倍,等效容量约为62.8%,较传统隔离式变压器等效容量小约37.2%。     

基于Prover的联锁软件形式化验证过程研究

计算机联锁系统是铁路信号控制系统的核心设备,是有着苛刻安全要求的复杂控制系统。本文采用Prover形式化开发工具对联锁软件安全需求进行形式化验证。通过模型检验的形式化验证方法,遍历系统输入变量的所有状态空间.验证联锁特定应用满足系统安全需求,确保系统的安全性得以正确实现。在保证系统安全性的基础上,以全状态空间查找反例的检验方法进一步提升产品的质量。     

基于全以太网的列车网络控制系统在美国地铁列车上的应用

从列车网络控制系统的拓扑结构、通信协议架构、冗余措施及功能描述等几个方面对基于全以太网的列车网络控制系统在美国地铁列车上的应用进行了详细分析与试验验证。在装车调试之前进行系统集成测试可尽早地发现列车网络控制系统或子系统在硬件和软件方面存在的各种问题,大大节省装车调试所需要的人力和时间。     

长大货物车适应THDS轴温探测技术的研究

针对不适应THDS轴温探测系统的长大货物车,分析论证了现车轴箱改进方案适应THDS轴温探测的不足,并提出了轴箱优化方案。经计算、试验和装车验证表明,新轴箱可行、有效、安全,满足THDS轴温探测要求,保证了长大货物车运输安全。     

公路平曲线设计在工程可行性研究阶段的探讨

文章针对工程可行性研究阶段的公路平面设计特点,介绍利用小计算器确定平曲线的平面设计方法,为提高工程可行性研究阶段设计的工作效率及质量提供参考。