论消防船的设计

国家经济快速发展,大量的消防船需要设计建造,本文就消防船设计中采用规范、消防船设计特点、消防能力的确定、船型及型线设计、尺度选择、消防设备配套选择、消防船总体及主要设备布置等方面进行简要论述。     

空气净化器风道的计算机仿真

在进行空气净化器风道结构的设计中,风道的结构形式对风量起着重要的影响。本文利用ICEPAK计算机仿真软件在设计阶段对空气净化器的风道进行模拟仿真,建立了风道的仿真模型及建模过程,仿真出风道进口处与出口处的空气流速的变化值,进一步研究离心风机的风量与滤层阻力、流量、流速的影响关系。通过实验比较,在不同滤器种类的情况下,验证了风阻对风量的影响大小,证明了空气净化器风道计算机仿真的正确性。     

块石基床爆夯技术在重力式码头的应用及质量控制

爆夯技术近年在重力式码头抛石基床上得到广泛应用,本文结合福建某重力式码头基床、地基及水文的实际情况,总结块石基床水下爆炸夯实技术的设计、施工工艺、质量控制及爆破的安全控制,以供类似工程参考。     

人工挖孔桩施工与质量控制

在地质奈件允许的情况下,可采用人工挖孔方法对桥梁进行桩基础的施工。人工挖孔受地形限制小,可以多孔同时作业,能加快工程进度并降低工程造价,是比较成熟的成孔方法。     

水下爆炸作用下箱形梁模型响应试验研究

对模拟水面舰船结构的箱形梁模型在水下爆炸作用下的响应进行试验,借助高速摄像机观测气泡脉动过程和结构响应过程,发现箱形梁结构在水下爆炸作用下的响应可以分为三个阶段.不同的爆点位置,气泡脉动能够激起不同振动形式的鞭状响应运动.     

Numerical simulations of fatigue crack initiation and propagation based on re-tensile plastic zone generating load criterion for in-plane gusset welded joints

Many accidents are caused by fatigue in welded built-up steel structures, and so it is important to estimate the fatigue lives of such structures quantitatively for safety reasons. By assuming that fatigue cracks cannot grow without an accumulation of alternating tensile/compressional plastic strain, one of the authors identified an improved effective stress intensity factor range ΔK _RPG based on the re-tensile plastic zone generating (RPG) load, which represents the driving force for fatigue cracks, and suggested that ΔK _RPG should be used as the parameter to describe fatigue crack growth behavior. The “FLARP” numerical simulation code in which ΔK _RPG is implemented as the fatigue crack growth parameter, was developed in order to predict fatigue crack initiation and propagation behavior. In this paper, it is demonstrated that FLARP gives accurate estimates for fatigue life by comparing the estimated fatigue crack growth curves and S–N curves with the experimental results for in-plane gusset welded joints, which are used in many welded steel structures. Moreover, the effect of induced bending moment due to the linear misalignment in the out of plane direction on the fatigue strength of in-plane gusset welded joints is investigated through numerical simulations.     

Workspace analysis to generate a collision-free torch path for a ship welding robot

We propose a method to determine the optimal initial location and to generate torch paths for a ship welding robot with 6 degrees of freedom (DOF). The optimal initial location is determined using an objective function, which is set up by combining constraints on the torch posture, manipulability, and the range of each joint angle to avoid collisions. A genetic algorithm (GA) is used to optimize the objective function because it does not require additional derivatives. After the initial location is determined, torch paths are generated by interpolating the starting point, endpoints and torch postures using inverse kinematics. Our method can be applied to automate the welding job for each block during ship building, irrespective of the shape of the robots, by changing the objective function.     

港口工程建设对湿地生态承载力的影响

采用以生态适宜性分析为基础的区域生态承载力评价,在地理信息技术的支持下定量获取各评价指标的信息,研究港口工程建设对湿地环境承载力的影响。研究表明,该方法是生态承载力评价方法的有效补充,弥补了生态承载力评价的不足。     

船体外加电流阴极保护系统设计中问题的探讨

船体外加电流阴极保护系统国家标准(GB/T3108-1999)中关于设计电流密度的选取并由此计算船体的保护电流总量.由于船舶的结构布局等因素,往往使电极不能按理想的设计方案在船体E进行布置与安装,致使有些部位电流不足,导致部分船体得不到充分的保护.经实船实验证明,在船体设计安装外加电流阴极保护系统的同时,应在艉部等部位相应没计安装部分牺牲阳极以弥补辅助阳极电流之不足.     

基于天线选择的准正交空时码的自适应设计

为充分利用信道信息(Channel State Information,CSI)来改善准正交空时码(Quasi Orthogonal Space-Time Block Code,QSTBC)系统的性能,提出基于天线选择的QSTBC系统自适应设计方案,对QSTBC的编码结构添加自适应系数,使信道矩阵正交化,消除码间串扰.推导了系统的瞬时输出信噪比,以此作为天线选择准则.仿真结果表明,相对于未经过自适应编码设计的天线选择QSTBC系统,新系统的误码率性能有明显改善.