Dynamic model for the wheel–rail contact friction

Accurately estimating the coefficient of friction (CoF) is essential in modelling railroad dynamics, reducing maintenance costs, and increasing safety in rail operations. The typical assumption of a constant CoF is widely used in theoretical studies; however, it has been noticed that the CoF is not constant, but rather depends on various dynamic parameters and instantaneous conditions. In this paper, we present a newly developed three-dimensional nonlinear CoF model for the dry rail condition and test the CoF variation using this model with estimated dynamic parameters. The wheel–rail is modelled as a mass–spring–damper system to simulate the basic wheel–rail dynamics. Although relatively simple, this model is considered sufficient for the purpose of this study. Simulations are performed at a train speed of 20 m/s using rail roughness as an excitation source. The model captures the CoF extremes and illustrates its nonlinear behaviour and instantaneous dependence on several structural and dynamic parameters.     

表面强化后的柴油机汽缸套/活塞环配副性试验分析

为提高柴油机汽缸套/活塞环摩擦副的耐磨减摩性能,延长其使用寿命,文中对经表面强化后的汽缸套、活塞环进行配副,组成9对摩擦副,通过试验,分析比较各摩擦副的摩擦系数、磨痕宽度、失重3个参数,得出最佳配副性组合为:气环镀CrTiAlN/缸套激光淬火+渗硫.     

Geometric design safety estimation based on tire–road side friction

A closed-loop drive–vehicle–road–environment system (DVRES) model was established using Adams/Car and Matlab/Simulink. Dynamic responses of lateral tire forces based on tire–road side friction and road geometric characteristics are used to investigate vehicle side slip for geometric design safety estimation. The root mean square, the maximum values of lateral tire forces, comfort limit on curves and vehicle trajectories are used to quantify the safety margin of side friction. The simulation results show that the safety margins of lateral tire forces for radius, operating speed and superelevation rate were 18.2%, 19.3% and 17.6%, respectively, to guarantee good vehicle lateral reliability and ride comfort, while lower speeds are optimal in wet and slippery roads. Finally, a case study was conducted to illustrate the analysis of road design safety, and on-site experiment testing further validated the accuracy and reliability of the closed-loop DVRES model.     

耐久性路面的结构设计

介绍耐久性路面的结构设计原则,并在此基础上提出柔+刚+柔的典型路面结构形式,论述提高沥青混凝土路面强度的措施及质量控制方法。     

半潜式钻井平台用三滚筒锚机研制

针对目前国内半潜式钻井平台配套用三滚筒式锚机研究文献较少的现状,开展三滚筒锚机的设计研究。该锚机最大额定拉力1 700 kN,容绳量3 500 m,结构采用双滚筒摩擦绞车和储存绞车配合形式,可满足1 200 m水深半潜式钻井平台应用。文中着重介绍了主要设计原理,并进行详细的校核计算及关键部件有限元分析,结论证明该设计合理,使用可靠且安全。     

基于应力释放的盾构隧道开挖地表沉降分析

以沈阳地铁1号线隧道为例，利用有限元方法研究盾构施工引起的横向地表沉降问题。引入地层损失和地应力释放的概念，分别在不同地层损失率、不同地应力释放率条件下，建立有限元模型进行计算。根据实际施工时监测到的地表沉降值与有限元模拟的地表沉降值进行比较，发现地表沉降值与地层损失率和地应力释放率成正比，〖ＪＰ＋１〗并通过最大地表沉降值的对比确定了该路段施工引起的地层损失率为1.747%，引起的地应力释放率为74.071%。利用同样的方法，确定了10座城市隧道开挖过程中引起的地层损失率区间为0.5%~2%、地应力释放率区间为60%~80%，并将地层损失率为1.747%和地应力释放率为74.071%时的衬砌混凝土管片处的最大弯矩与无地层损失、无地应力释放率模型管片处的最大弯矩值进行对比，可以发现最大弯矩值有明显的减小，分别减小了76.16%和71.82%。且2种方法得到的弯矩值非常接近，可以认为地层损失率模型和地应力释放率模型是等效的。     

三维设计在船体结构中的应用

在三维空间里设计水面舰艇的船体结构是军船结构设计的发展趋势。介绍船体结构三维设计的构思;三维设计方法与传统二维设计方法的比较;目前三维设计可达到的设计深度。详细论述结构三维设计的研究内容和具体实施方法,揭示三维设计中的关键技术,最后提出舰艇船体结构三维设计的发展构想。     

有自由液面的陷落式圆腔流噪声实验研究

采用基于经验模态分解(EMD)的本征模态函数(IMF)分析法和对比实验法研究了有自由液面的陷落式圆腔的流噪声,实验流速为0.4m/s~2.0m/s,间隔0.2m/s。实验发现当流速为0.4m/s~0.6m/s时,腔内液体有明显的振荡现象,其表现形式为液体沿腔内深度方向的大幅上下运动,称为“活塞(Piston)”现象。当流速大于等于0.8m/s时,腔内无振荡现象出现。通过对背景噪声和腔流噪声的本征模态函数作对比分析,得到了腔内流噪声的特性。     

高等级公路路面平整度的保证措施

为了保证高等级公路路面平整度指标,应合理选用机械设备,加强现场施工管理,精心安装伸缩缝,以满足公路的使用品质。     

An Intelligent Response Surface Methodology for Modeling of Domain Level Constraints

An effective modeling method of domain level constraints in the constraint network for concurrent engineering （CE） was developed. The domain level constraints were analyzed and the framework of modeling of domain level constraints based on simulation and approximate technology was given. An intelligent response surface methodology （IRSM） was proposed, in which artificial intelligence technologies are introduced into the optimization process. The design of crank and connecting rod in the V6 engine as example was given to show the validity of the modeling method.