The Kalker book of tables for non-Hertzian contact of wheel and rail

A new regularisation of non-elliptical contact patches has been introduced, which enables building the look-up table called by us the Kalker book of tables for non-Hertzian contact (KBTNH), which is a fast creep force generator that can be used by multibody dynamics system simulation programs. The non-elliptical contact patch is regularised by a simple double-elliptical contact region (SDEC). The SDEC region is especially suitable for regularisation of contact patches obtained with approximate non-Hertzian methods for solving the normal contact problem of wheel and rail. The new regularisation is suitable for wheels and rails with any profiles, including worn profiles.

The paper describes the new procedure of regularisation of the non-elliptical contact patch, the structure of the Kalker book of tables, and parameterisation of the independent variables of the tables and creep forces.

A moderate volume Kalker book of tables for SDEC region suitable for simulation of modern running gears has been computed in co-simulation of Matlab and program CONTACT.

To access the creep forces of the Kalker book of tables, the linear interpolation has been applied.

The creep forces obtained from KBTNH have been compared to those obtained by program CONTACT and FASTSIM algorithm. FASTSIM has been applied on both the contact ellipse and the SDEC contact patch. The comparison shows that KBTNH is in good agreement with CONTACT for a wide range of creepage condition and shapes of the contact patch, whereas the use of FASTSIM on the elliptical patch and SDEC may lead to significant deviations from the reference CONTACT solutions.

The computational cost of calling creep forces from KBTNH has been estimated by comparing CPU time of FASTSIM and KBTNH. The KBTNH is 7.8–51 times faster than FASTSIM working on 36–256 discretisation elements, respectively.

In the example of application, the KBTNH has been applied for curving simulations and results compared with those obtained with the creep force generator employing the elliptical regularisation. The results significantly differ, especially in predicted creepages, because the elliptical regularisation neglects generation of the longitudinal creep force by spin creepage.     

提高车用发动机活塞环摩擦学性能的试验研究

制备了直接离子渗氮环与超声滚压加工-离子渗氮环两类摩擦学试样。利用电子显微镜、硬度计、X射线衍射仪和能谱仪,对表面改性层进行了表征,分析了超声滚压预处理对316L不锈钢活塞环离子渗氮行为的影响;在润滑油条件下,使用往复式摩擦磨损试验机,对比考察了直接渗氮环和超声滚压-渗氮环的摩擦学性能。结果表明,超声滚压-渗氮环相对于直接渗氮环渗氮层的氮含量增加了2.9倍,显微硬度提高了1.1倍,摩擦因数降低了0.04,耐磨性提高了2.8倍。发动机台架试验表明,超声滚压-渗氮环与硼铸铁氮化气缸套的匹配性最好。     

基于VDI2230-2003标准的动车组车钩联接螺栓强度分析

使用ANSYS软件对某车钩安装座及其联接螺栓进行接触非线性静强度计算,在此基础上基于德国《VDI2230-2003螺栓强度校核标准》对螺栓进行强度评估,并和传统《机械设计手册》计算的结果进行比较,得出两种方法的计算值均满足强度要求,同时前者计算的轴向拉应力水平为后者计算的应力水平的72%,但剪切应力两者相同.     

钢轨的移动式接触焊工艺

介绍了移动式接触焊在广州地铁3号线中的施工工艺及施工过程;分析施工过程中应该注意的曲线钢轨焊接、环境保护、曲线钢轨焊接接头平直度的测量、设备维修保养等技术要点。     

浅谈滚动物料计划在汽车行业中的应用

随着汽车逐年普及,消费者需求多样化、个性化随着增长,而且消费者对提车周期要求越来越高.汽车生产企业如何快速、高效的占领市场,同时降低供应链物流成本,是目前自主品牌汽车企业面临重大挑战.需要从软硬件进行全面提升竞争能力,物料组织改进是整个汽车供应链改进不可缺少的一个重要环节,能帮助企业迅速占领市场,以最小的成本换取最大利...     

铜合金接触线禁用承导双架施工方法的建议

通过分析高速悬挂系统的特点和工艺标准,从施工效率、施工质量、施工工艺等方面对采用承导双架施工方法进行探讨,认为承导双架施工方法对施工效率的提高不明显、质量存在隐患且工艺上易产生不可克服的缺陷,建议在使用锡(镁)铜合金接触线或新线一次建设电气化工程中禁止采用承导双架施工方法.     

改善刚柔过渡区域弓网关系的探讨

对刚柔过渡区域刚性和柔性接触网的弹性不同及接触线高度不等情况进行了定性及定量分析,找出该区域弓网关系恶劣的原因,并针对原因提出改善刚柔过渡区域弓网关系的解决方案。     

深圳地铁地面接触网避雷器运行分析及改造

根据避雷器的作用和原理,以及地面接触网避雷器的设计安装原则,分析深圳地铁避雷器在运行中存在的问题,提出整改措施及提高防雷技术的建议。     

轨道机车车辆运用强度检验的现代化方法——关于德国铁路股份公司(DB AG)2005年3月10日柏林学术会议的报告

介绍了"机车车辆运用强度"课题的立项背景、项目的目标及部署、载荷分布的研究和调研情况,并概述了相关论文报告.     

牛仔布水洗废水的处理及回用

该文介绍了采用混凝沉淀+生物接触氧化法处理牛仔布水洗废水的处理工艺以及经过深度处理后回用于生产用水的方法,并对其进行了经济分析。