多年冻土区钻孔灌注桩施工过程热力特性研究

钻孔灌注桩水化热会暖化冻土引起桩基承载力下降,以桩基水化热在时间与空间上的影响效应为研究目的,结合青藏公路G214沿线查拉坪旱桥桩基观测数据,分析水化热对地温场的扰动范围以及桩周土回冻时间,给出灌注桩18 d内的养护温度。结果表明:水化热对距桩1.95 m以外地温影响微弱;144 d后桩侧温度降至0℃以下,229 d后桩侧温度低于-0.5℃;2 a后桩侧基本回冻至天然地温,此时承载力已达到设计要求。桩基混凝土养护温度前5 d在10℃以上,5~12 d在5℃以上,12~15 d为2℃以上,15~18 d仍高于0℃。通过数值仿真给出混凝土入模温度及桩基施工时间对桩周温度场的影响,模拟结果显示,该区域的灌注桩施工可以在相应规范规定范围内提高混凝土入模温度;灌注桩施工可以在冷季进行,但要做好5 m以上深度桩基混凝土的温控措施。     

Mental models of driving and speed: biases,choices and reality

This paper provides a review of research performed by Svenson with colleagues and others work on mental models and their practical implications. Mental models describe how people perceive and think about the world including covariances and relationships between different variables, such as driving speed and time. Research on mental models has detected the time-saving bias [Svenson, O. (1970). A functional measurement approach to intuitive estimation as exemplified by estimated time savings. Journal of Experimental Psychology, 86, 204–210]. It means that drivers relatively overestimate the time that can be saved by increasing speed from an already high speed, for example, 90–130?km/h, and underestimate the time that can be saved by increasing speed from a low speed, for example, 30–45?km/h. In congruence with this finding, mean speed judgments and perceptions of mean speeds are also biased and higher speeds given too much weight and low speeds too little weight in comparison with objective reality. Replacing or adding a new speedometer in the car showing min per km eliminated or weakened the time-saving bias. Information about braking distances at different speeds did not improve overoptimistic judgments of braking capacity, but information about collision speed with an object suddenly appearing on the road did improve judgments of braking capacity. This is relevant to drivers, politicians and traffic regulators.     

冲压机械振动对高铁桥梁及行车动力影响分析

高速铁路桥梁的平顺性和稳定性对运营列车的平稳性和安全性有很大影响。为研究冲压机械产生的外部振动激励对高铁桥梁的影响,首先通过对此机械引起的地面振动进行实测,并结合有限元分析软件,确定最大冲击荷载作用下产生的地面振动及传播至桥墩处的振动;然后通过建立列车-轨道-桥梁耦合动力学模型,将桥墩处的地面振动作为激励输入,分析列车以不同速度通过时车辆、桥梁动力学响应。结果表明:地面冲击振动有限元模型计算结果与实测结果基本相符,验证了模型的可靠性;地面振动对桥梁响应会产生一定的影响,距振源50 m处地面振动对桥梁所产生的影响较距振源80 m处(桥墩处)的大,但对运行车辆的影响很小;随着车速由250 km/h至350 km/h,车辆及桥梁各结构的动态响应均有所增大,但都未超出安全限值。因此,冲压机械冲击作用导致的地面振动对列车-轨道-桥梁系统动态服役性能影响非常有限。     

探地雷达在桥梁预应力管道定位检测中的应用

对预应力管道进行定位检测,是目前桥梁无损检测技术的一个重要问题,在阐述探地雷达无损检测技术原理和方法的基础上,通过室内模型试验,并结合工程实例说明了高精度探地雷达在桥梁预应力管道定位检测中的应用,及其无损、简易、效率高、精度高、抗干扰能力强的优点,为准确评价桥梁结构耐久性和安全使用功能提供科学依据。     

软土地层盾尾注浆压力引起的地面隆起分析

目前已有盾尾注浆压力引起地面隆起的研究均假定盾尾注浆压力均匀分布,这与实际工程中盾尾注浆压力上小下大的形式不符。为更准确预测盾尾注浆压力引起的地面变形,在现有均匀注浆压力引起地面隆起分析的基础上,考虑软土地层盾构隧道施工中盾尾注浆压力上小下大的分布形式,将盾尾注浆对地层的压力效应视为半无限土体中柱形孔的扩张过程,利用镜像法和Mindlin解,推导出软土地层盾尾注浆压力引起的地面隆起计算公式,并通过工程实例,将本文解答、叶飞解答、林存刚经验公式解答、Vesic解答与数值解进行对比分析。结果表明:盾尾注浆压力引起的地面隆起横向曲线总体上呈高斯分布。在预测软土地层地面沉降时,忽视盾尾注浆压力引起的地面隆起是不合理的;用推导出的公式计算上小下大分布形式下盾尾注浆压力引起的地面沉降是可行的,Vesic公式和林存刚经验公式在应用时需要根据具体工程进行相应修正。     

使用聚合物对纯砂层进行渣土改良的试验研究

土压平衡盾构在不同的地层进行渣土改良的关键是选择合适的改良剂,纯砂层施工中最常用的改良剂就是膨润土泥浆,目前已开始尝试使用聚合物进行改良。本文选取3种典型的聚合物,研究聚合物溶液特性与聚合物浓度、搅拌时间和静置时间的关系,并选择合适的聚合物对粗砂试样进行塌落度试验、渗透试验和直剪试验的室内试验研究。研究结果表明,针对粗砂地层(含水率10%左右),0.3%的PAM聚合物溶液注入率为20%~25%时,能有效增强粗砂的流动性和黏聚性,降低渗透系数和摩擦因数,满足土压平衡盾构施工要求。     

圆形隧道施工对不同深度地层沉降影响的模型试验研究

为了预测圆形隧道施工引起地表以下不同埋深地层沉降特征,首先,通过理论推导不同地层最大沉降位移与沉降槽宽度系数的函数关系;然后,建立包括试验台架、地层模型、圆形隧道开挖模型以及测量地层变形装置的平面应变模型试验系统。通过理论解析和模型试验可知:1)地表以下地层的最大沉降位移与沉降槽宽度系数成反比;2)不同深度地层的沉降位移随着地层埋深的增加而增大,且地表以下地层沉降槽曲线仍然符合正态分布;3)通过对模型试验数据进行回归分析,得到黏土地表以下不同深度地层沉降槽宽度系数的计算公式,从而为预测圆形隧道施工地表以下不同深度地层竖向位移提供了一种可靠的计算方法。     

极高地应力软岩隧道超前导洞应力释放及多层支护变形控制技术

为了解决极高地应力软岩隧道大变形控制难题,以兰渝铁路木寨岭隧道岭脊核心段施工为例,通过现场试验和数据分析,得到如下主要结论:1)提出了"先放后抗,抗放结合,锚固加强"的变形控制理念;2)得出了该隧道岭脊核心段"超前导洞应力释放+圆形4层支护结构+径向注浆+长锚杆+长锚索"综合变形控制方案;3)超前导洞应力释放效果明显,正洞累计变形减小幅度约为34%;4)得到了圆形多层支护结构变形规律;5)累计变形均控制在设计预留变形量内,保证了该隧道岭脊核心段大变形控制效果。     

废气旁通阀开度对增压直喷汽油机部分负荷性能的影响

汽油机节气门产生的节流损失对增压发动机泵气损失的影响相当严重,尤其是在中小负荷时,针对这一问题采用试验的方法研究了中小负荷下旁通阀开度对增压直喷汽油机性能的影响。研究结果表明,在节气门开度较小的小负荷工况下,涡轮增压器不宜工作,否则排气背压过大,对发动机非常不利;而废气旁通阀全开可以减小排气背压,能使发动机的动力性和经济性提高3%左右。对废气旁通阀的合理控制可以实现发动机在自然吸气和涡轮增压两种模式之间的转换。     

Magneto-rheological suspensions for improving ground vehicle’s ride comfort,stability, and handling

ABSTRACT

A state-of-the-art discussion on the applications of magneto-rheological (MR) suspensions for improving ride comfort, handling, and stability in ground vehicles is discussed for both road and rail applications. A historical perspective on the discovery and engineering development of MR fluids is presented, followed by some of the common methods for modelling their non-Newtonian behaviour. The common modes of the MR fluids are discussed, along with the application of the fluid in valve mode for ground vehicles’ dampers (or shock absorbers). The applications span across nearly all road vehicles, including automobiles, trains, semi-trucks, motorcycles, and even bicycles. For each type of vehicle, the results of some of the past studies is presented briefly, with reference to the originating study. It is discussed that Past experimental and modelling studies have indicated that MR suspensions provide clear advantages for ground vehicles that far surpasses the performance of passive suspension. For rail vehicles, the primary advantage is in terms of increasing the speed at which the onset of hunting occurs, whereas for road vehicles – mainly automobiles – the performance improvements are in terms of a better balance between vehicle ride, handling, and stability. To further elaborate on this point, a single-suspension model is used to develop an index-based approach for studying the compromise that is offered by vehicle suspensions, using the H₂ optimisation approach. Evaluating three indices based on the sprung-mass acceleration, suspension rattlespace, and tyre deflection, it is clearly demonstrated that MR suspensions significantly improve road vehicle’s ride comfort, stability, and handling in comparison with passive suspensions. For rail vehicles, the simulation results indicate that using MR suspensions with an on-off switching control can increase the speed at which the on-set of hunting occurs by as much as 50% to more than 300%.