5000 PCC“SHANGHAI HIGHWY”船主机启动分析与处理

分析5 000 PCC"SHANGHAI HIGHWAY"船主机伺服油压低引起主机启动故障的原因、介绍调查与处理过程,在实施了恰当的处理方法后,解决了问题。以期为类似问题的处理与解决提供借鉴和参考。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

铁路路基动态变形模量的数值模拟分析

介绍铁路路基动态变形模量理论计算公式的推导及动态变形模量的测试原理,采用有限元软件模拟动态变形模量的测试过程,分析承载板与土体接触压力、路基动态变形模量的影响因素,并计算动态变形模量的有效测试深度.结果表明:在承载板中心一定范围内,接触压力模拟结果较理论计算值大;土体的动弹性模量对接触压力影响很小,可以忽略;路基动态变形模量测试冲击荷载作用下,土体只发生弹性变形;动态变形模量与土体动弹性模量呈线性关系,路基动态变形模量的模拟结果大于理论计算值;土体的泊松比对动态变形模量影响较小;动态变形模量有效测试深度建议取0.5~0.6 m.     

船舶低硫柴油系统设计的分析与优化

就新辟航线首制船“汉亚直达”集装箱船的低硫柴油系统,叙述了船舶低硫柴油系统的设计经验,从当前国内外对船用燃油硫含量的要求、应对方案到船舶低硫柴油冷却方式选择、低硫柴油冷却系统设计、高/低硫柴油转换、使用低硫柴油风险分析及处理等方面进行详细叙述,为业内同行提供参考。     

Modeling free-flow speed according to different water depths—From the viewpoint of dynamic hydraulic pressure

In this paper, we propose a method of modeling free flow speed from the viewpoint of hydroplaning. First, the lift forces for different water depths were estimated using Bernoulli’s equation. Compared with the result of the experimental test performed by the Japan Automobile Research Institute, the hydrodynamic pressure coefficient was determined to be 0.03 (tf s²/m⁴). The validation of the predicted lift force is found in another published paper. A very good match is found between the computed values by the proposed numerical model and the data in other published papers. Then, the loss of contact force is considered to evaluate the hydroplaning performance of a tire. To simulate the hydroplaning speed, a tire-sliding model was utilized to obtain the traction and friction forces between the road surface and the tire. The observation data obtained in Japan in 2009 is compared with the physically computed hydroplaning speed, yielding the conclusion that the traction force at the measured desired speed is, on average, 23.4% of the traction force at hydroplaning speed. The analytical model offers a useful tool to quantitatively show that the free flow speed changes as the water depth increase.     

双块式轨枕外形质量快速检测系统研制及应用

SK?2型双块式混凝土轨枕是高速铁路无砟轨道结构中的重要预制件,单一生产厂日均产量达到800~1400根,但目前的人工检测方式无法满足双块式轨枕的出厂检验要求。本文提出的双块式轨枕外形质量快速检测系统可满足TB/T 3397—2015《CRTS双块式无砟轨道混凝土轨枕》的出厂检验要求,与双块式轨枕生产线相匹配,大大提高了检测效率,实现了双块式轨枕全参数、自动化、智能化检测。检测数据自动上传至生产管理平台,可对双块式轨枕生产质量进行跟踪管理。     

南昌地铁砾砂层渣土改良技术试验研究

随着土压平衡盾构的广泛推广和应用,其地层适应性也越来越强,但盾构机在一些特殊地层中掘进时,渣土无法满足盾构施工对渣土流塑性的要求,易造成刀盘结饼、掌子面压力不稳定、刀盘磨损严重等问题。泡沫渣土改良技术是保证施工安全、顺利进行的关键技术之一。本文针对两种工程现场常用的泡沫进行泡沫基础性能试验,并以南昌地铁3号线盾构区间为工程背景,针对该区间砾砂地层进行改良渣土坍落度试验,对不同注入率和不同发泡剂的改良效果进行分析。研究发现,两种泡沫剂的建议使用浓度为3%;渣土流动性随泡沫注入率的增大而提高。在试验所用土样条件下,建议施工时使用的泡沫注入率为20%~30%。     

深海超高压环境模拟容器裂纹评定

深海超高压环境模拟容器用于模拟水下压力环境,其容器壁上承受反复载荷,容易产生疲劳裂纹.疲劳裂纹扩展是影响其断裂的主要因素.本文旨在分析半椭圆裂纹在老化的深海超高压环境模拟容器中的扩展行为,评估容器的安全性,因此对材料20MnMoNb钢的裂纹扩展特性进行了试验研究,首先考虑三角形和梯形加载情况,通过比较两组实验结果,考察了其材料对保载时间的敏感性.采用基于统一的裂纹扩展率模型的三维有限元方法进行了疲劳裂纹扩展计算,并通过CT试样的一组数值和实验结果进行了验证,最后建立了不同初始尺寸、展弦比和倾角的裂纹有限元模型,并根据裂纹在容器内壁的容许深度准则,计算了容器的剩余寿命.其分析结果可为深海超高压环境模拟容器可靠性评估提供参考.     

Structural safety assessment procedure for membrane-type LNG CCS considering hydroelasticity effect

As environmental regulations have become more onerous, the demand for LNG and LNG carriers has increased. The LNG cargo containment system (LNG CCS) is one of the most important facilities in LNG carriers, and many membrane types of LNG CCS have been developed so far. Traditionally, sloshing model tests are performed and a series of statistical approaches are used to obtain design sloshing pressures. Then, these design loads are utilized to analyze the structural safety of LNG CCS. In the sloshing model test, the flat and almost rigid plate is used as the LNG CCS instead of a real model, and thus, the hydroelasticity effect cannot be considered. In the present research, the effect of hydroelasticity on sloshing pressure was investigated in a fluid-structure interaction simulation. A wet drop simulation was conducted, and its results subsequently were compared with wet drop experimental test results to ensure their validity. Then, two types of structure model, namely a flat-rigid plate model and a flat-flexible CCS model, were generated to investigate the effect of hydroelasticity. Also, a fluid hitting analysis model was devised to realize the sloshing phenomenon, and the two generated structure models were applied as the structure domain in the analysis. In the fluid hitting simulations, it was found that the hydroelasticity effect on sloshing pressure is significant. Thus, correction factors, which are quantitative values of the effect of hydroelasticity, were derived (and are proposed herein). Finally, a structural safety assessment procedure for consideration of the hydroelasticity effect was derived (and is suggested herein).     

25t轴重荷载作用下隧底脱空区域受力特性分析

为了研究在役铁路隧道在通车之后隧底脱空病害的问题,采用有限元理论,建立隧道脱空区域在围岩压力与25 t轴重列车动载作用下的数值计算模型,主要研究80 cm与40 cm脱空宽度分别距隧道中心线0,80 cm与160 cm时脱空区域的受力特性。结果表明:在围岩压力下,脱空区域中线上壁和外侧顶角混凝土中产生拉应力及内侧顶角中产生压应力,其中压应力对脱空的宽度更为敏感;同时施加列车动载作用时,脱空区域上壁出现了竖向动应力与横向拉应力,得到了脱空区域力学指标的最大响应值及其出现的具体位置,宽度的增加对脱空区上壁横向拉应力更为显著,上壁横向拉应力增幅超过200%,竖向动应力增幅达50%。因此,隧底脱空区周围应力分布复杂,拉应力与压应力在脱空区域同时存在,应力突变严重,对脱空现象应及时组织处理。