全文获取类型
收费全文 | 587篇 |
免费 | 53篇 |
专业分类
公路运输 | 155篇 |
综合类 | 216篇 |
水路运输 | 176篇 |
铁路运输 | 78篇 |
综合运输 | 15篇 |
出版年
2024年 | 4篇 |
2023年 | 8篇 |
2022年 | 12篇 |
2021年 | 18篇 |
2020年 | 18篇 |
2019年 | 17篇 |
2018年 | 19篇 |
2017年 | 19篇 |
2016年 | 8篇 |
2015年 | 21篇 |
2014年 | 47篇 |
2013年 | 53篇 |
2012年 | 61篇 |
2011年 | 55篇 |
2010年 | 42篇 |
2009年 | 31篇 |
2008年 | 35篇 |
2007年 | 37篇 |
2006年 | 42篇 |
2005年 | 22篇 |
2004年 | 20篇 |
2003年 | 11篇 |
2002年 | 7篇 |
2001年 | 8篇 |
2000年 | 6篇 |
1999年 | 2篇 |
1998年 | 1篇 |
1997年 | 3篇 |
1996年 | 1篇 |
1995年 | 1篇 |
1994年 | 2篇 |
1993年 | 2篇 |
1992年 | 2篇 |
1991年 | 4篇 |
1986年 | 1篇 |
排序方式: 共有640条查询结果,搜索用时 31 毫秒
161.
依托宁波地区某主干道周边基坑地下连续墙施工工点,通过现场取样测试土体动三轴下强度指标;采用三维有限元数值模拟判别交通和施工超载作用下槽壁整体失稳模式;并以槽壁外侧土体达到剪切塑性极限为临界条件,采用极限平衡法,推导单一土层内一字型地下连续墙槽壁整体失稳的判定公式。研究结果表明:地下连续墙槽壁呈现类似四棱锥形整体失稳形态;护壁泥浆出现补充不及时或漏浆时,槽壁将发生整体失稳破坏。 相似文献
162.
基于局部线性模型树的高压共轨柴油机排放模型 总被引:3,自引:0,他引:3
为研究面向闭环控制的柴油机在线排放模型,以1台高压共轨、涡轮增压中冷柴油机的转速、扭矩、空燃比、燃烧始点、燃烧重心、燃烧终点、最高燃烧温度、最大缸内压力等运转和燃烧的各项参数为基础,运用局部线性模型树对排放物HC,CO,CO2,NOx和烟度进行了仿真研究。研究结果表明,以转速、扭矩、空燃比为输入时,CO,CO2,NOx的仿真结果与试验值具有较好的一致性,以转速、扭矩、空燃比、燃烧重心为输入时,HC、烟度的仿真结果与试验值具有较好的一致性。各排放的期望响应与仿真输出的平均误差在10%以内,线性回归相关系数达到0.96以上。各个排放物的仿真过程单独进行时,可以得到较好的仿真效果。因此,局部线性模型树模型适用于高压共轨柴油机排放物的仿真。 相似文献
163.
164.
165.
166.
随着多样化军事任务的增多,利用民船进行军事运输的行动也随之增加,但大部分民船的军事适运性较差,在运输军事装备前需要进行慎重选择,必要时要进行适当的加改装。针对民船运输重装备中的船舶局部强度校核方法进行研究,认为:传统计算方法计算简单,略显粗糙,适合判断性计算校验;改进的精确计算方法能够根据船舶板架的结构和重大件装备的尺寸、重量等具体数据进行详细精确计算,结论能够直接应用于实践装载。两种方法相互结合,使得重大件装备装载过程中既能够做到快速定位,又能够做到局部强度准确校核,达到及时、快速、安全、系统装载的目的。 相似文献
167.
三峡库水位变动诱发和加剧了崩滑地质灾害,崩滑体破坏弹冲动力特性亟待研究.针对滑塌式危岩,建立了力学模型,构建了危岩体失稳弹冲动能计算方法;通过数学与物理描述,得到了判别危岩动力失稳的重要指标;指出危岩体动力失稳瞬间系统的临滑聚能将释放并转换为危岩崩落动能,揭示了动力系统能量释放量与弹冲动力参数的关系. 相似文献
168.
The constructive disposition of metallic and plastic layers confers flexible pipes with high and low axial stiffness respectively when tensile and compressive loads are applied. Under certain conditions typically found during deepwater installation or operation, flexible pipes may be subjected to high axial compression, sometimes accompanied by bending. If not properly designed, the structure may not be able to withstand this loading and fails. From practical experience observed offshore and in laboratory tests two principal mechanisms, which will be discussed in this paper, have been identified regarding the configuration of the armor wires. When the pipe fails by compression the armor wires may exhibit localized lateral or radial deflections, consequently permanent damage is observed in the armor wires with a sudden reduction of the structure’s axial stiffness. The pressure armor may also unlock, thus causing potential fluid leakage.In this work a finite element model is developed to estimate the critical instability load and failure modes. An axi-symmetric model is constructed employing a complex combination of beam and spring elements. For each armor layer only one wire needs to be modeled, hence the computational cost is minimized without compromising the phenomenon characterization. A parametric case study is performed for a typical flexible pipe structure, where the friction coefficient between the wire armors and the external pressure are varied, and the critical instability loads and failure modes are obtained and results are discussed. 相似文献
169.
170.