Sasowam及Sasobit改性沥青及温拌混合料温度性能对比试验研究

通过室内试验,对比分析了Sasowam及Sasobit两种改性剂对沥青的改性效果,并通过温拌混合料试验,研究了两种改性剂对混合料高温性能和低温性能的影响。     

西部原油管道输量与能耗分析

为降低西部原油管道管输能耗,通过计算管道在不同季节、不同流量下的摩阻损耗,结合管道参数和输油泵特性曲线,分析得出影响输油生产单位能耗的因素包括管输流量和输油温度。进一步计算得出了不同流量和不同季节对应的输油生产单耗。结果表明,流量对输油生产单耗影响较大,西部原油管道管输流量在1 000~1 400 m~3/h区间时生产单耗相对较低;流量大于1 600 m3/h时,生产单耗随流量上升接近线性增长。而输油温度对生产单耗的影响较小,同一流量下冬季生产单耗略高于夏季生产单耗。     

船舶机舱火灾中回燃现象的数值计算与分析

采用大涡模拟(LES)技术,对某双机双桨船舶机舱火灾进行封舱灭火过程中所出现的回燃现象进行了数值模拟.结合舱内温度研究了该过程中回燃现象产生的原因及过程,并对热量释放率、辐射量、热对流及温度场分布进行了分析,同时对回燃现象的危害性进行了说明.通过结果详细分析了从经验层次上所无法观察到的回燃现象所产生的影响,也为船舶机舱火灾的评估、船舶设计、防火规范的修订及灭火策略提供了重要参考.     

The structure of dissipation in the western Irish Sea front

We report on an intensive campaign in the summer of 2006 to observe turbulent energy dissipation in the vicinity of a tidal mixing front which separates well mixed and seasonally stratified regimes in the western Irish Sea. The rate of turbulent dissipation ε was observed on a section across the front by a combination of vertical profiles with the FLY dissipation profiler and horizontal profiles by shear sensors mounted on an AUV (Autosub). Mean flow conditions and stratification were obtained from a bed mounted ADCP and a vertical chain of thermistors on a mooring. During an Autosub mission of 60 h, the vehicle, moving at a speed of ~ 1.2 m s^− 1, completed 10 useable frontal crossings between end points which were allowed to move with the mean flow. The results were combined with parallel measurements of the vertical profile of ε which were made using FLY for periods of up to 13 h at positions along the Autosub track. The two data sets, which show a satisfactory degree of consistency, were combined to elucidate the space–time variation of dissipation in the frontal zone. Using harmonic analysis, the spatial structure of dissipation was separated from the strong time dependent signal at the M₄ tidal frequency to yield a picture of the cross-frontal distribution of energy dissipation. A complementary picture of the frontal velocity field was obtained from a moored ADCP and estimates of the mean velocity derived from the thermal wind using the observed density distribution. which indicated the presence of a strong (0.2 m s^− 1) jet-like flow in the high gradient region of the front. Under neap tidal conditions, mean dissipation varied across the section by 3 orders of magnitude exceeding 10^− 2 W m^− 3 near the seabed in the mixed regime and decreasing to 10^− 5 W m^− 3. in the strongly stratified interior regime. The spatial pattern of dissipation is consistent in general form with the predictions of models of tidal mixing and does not reflect any strong influence by the frontal jet.     

低温储罐失效分析及预防措施

文中对低温设备温差应力循环所产生的疲劳失效事故进行了分析,目的是防止低温储罐在使用中出现疲劳破坏。文中通过对失效低温设备断口形貌特征的勘察,采用断口分析、焊接缺陷分析、温差应力循环与疲劳载荷分析的方法,得出了低温液体储罐设备在使用中易出现疲劳失效模式的结论。同时,从设计结构、施焊控制、安全泄放装置维护等方面,对低温液体储罐疲劳失效提出了预防措施。     

Superpave-13沥青混合料高温稳定性分析

文章结合天水过境高速公路路面实体工程,对不同孔隙率条件下的Super-pave-13高性能沥青混合料进行了车辙试验及SPT试验分析。结果表明,要保证Superpave-13沥青混合料具有较好的高温稳定性,其压实孔隙率应控制在4%～6.5%范围内。     

大体积混凝土凝固过程中的温度控制

进行大体积混凝土施工时必须根据混凝土水化热的具体情况,配备相应的监控系统—混凝土温度测试系统,对大体积混凝土凝固过程中的水化热进行实时温度检测,并对凝固过程进行全程检测和控制,采取相应的控制措施。     

燃料电池气体温湿度与电堆性能分析

系统性能指标是实现燃料电池工程化应用的瓶颈之一,系统搭建和调试过程中,空气与燃料温湿度是影响质子交换膜燃料电池性能的重要因素,对系统控制策略和辅机搭配方案的制定产生很大影响。本文通过实验与统计相结合的研究方式,研究15 kW燃料电池电堆在增湿温度分别为60℃、70℃和80℃条件下分别进行氢空单侧增湿、双侧增湿和不增湿时的输出功率、发电效率和单电池电压一致性。其中输出功率采用测试台直接测量、发电效率通过经验公式计算、电压一致性则通过巡检记录和统计方法相结合的方式评价。结果表明70℃时各增湿方案下优于其他温度同等湿度条件下的电堆性能,有增湿条件明显优于无增湿方案电堆性能,而双侧增湿和氢空单侧增湿对电堆性能影响不大。     

一种单片机控制的水温测试系统

由于现代多样的电子控制技术和电子控制理论的迅猛发展,高精度的机械在各类工业控制系统、生产线等方面的需求越来越大.其中以单片机为核心实现的数字控制器,因其体积小、简便易行等优点,而被广泛应用于各行各业.本文将单片机的温度控制系统作为设计核心,通过温度传感器、单片机等软件系统图,并利用软件编程,从而达到实现水温控制的目的....     

A model for prediction of the transient rolling resistance of tyres based on inner-liner temperatures

Measurements of rolling resistance in thermal equilibrium of a tyre, like measurements according to ISO 28580, do not allow statements about rolling resistances under other driving conditions. Such statements, however, are necessary to determine the energy consumption in driving cycles. Especially for the proper calculation of electric-vehicle remaining ranges and the selection of the respective driving strategies, the real amount of energy consumption is required. This paper presents a model approach, which by means of only one standardised rolling resistance measurement can be parameterised and, considering the present driving speed and tyre temperature, can predict the respective current rolling resistance.