南昌红谷沉管隧道短管节干坞内拉合对接施工技术

沉管隧道最终接头短管节在牵移和拉合过程中易发生偏移与倾斜,且GINA止水带压缩到设计值难度较大。以南昌红谷沉管隧道为例,从准备、牵移、拉合及后处理4个阶段介绍短管节对接拉合施工工艺。通过对底钢板打磨、涂抹黄油等,减小底部摩擦阻力。采用计算机控制液压同步提升系统、液压数据量测、钢端壳间距测量等措施,对短管节轴线及平面控制。实践表明:GINA止水带压缩量误差仅为+4 mm,短管节轴线及平面偏差均在可控范围内,短管节干坞内拉合对接操作可行、质量可靠。     

我国城市防洪排涝地下深隧规划设计与施工方法

为了建设符合中国国情的地下排水深隧,解决城市内涝问题,消除"城市看海"现象,采用调研分析的研究方法,通过调研国外城市排水深隧建设的成功案例,借鉴成熟经验并结合我国国情探索出我国城市排水深隧在规划设计、施工技术等方面的建设模式。主要结论如下:1)深隧规划必须坚持雨污分流原则,防涝标准应设为百年一遇;2)深隧层位应建于地下30~50 m的位置,隧道管线应布设在城市易涝区,并且将修建深隧、改造浅管和清淤河道衔接起来,形成一套完整的防洪排涝系统,让深隧的作用得以充分发挥,才能解决城市内涝问题;3)排水深隧要注重防水设计,防止雨水污染地下水;4)为提高深隧的经济效益,应将深隧与地下快速路的规划结合起来,功能上多样化。     

极高地应力软岩隧道超前导洞应力释放及多层支护变形控制技术

为了解决极高地应力软岩隧道大变形控制难题,以兰渝铁路木寨岭隧道岭脊核心段施工为例,通过现场试验和数据分析,得到如下主要结论:1)提出了"先放后抗,抗放结合,锚固加强"的变形控制理念;2)得出了该隧道岭脊核心段"超前导洞应力释放+圆形4层支护结构+径向注浆+长锚杆+长锚索"综合变形控制方案;3)超前导洞应力释放效果明显,正洞累计变形减小幅度约为34%;4)得到了圆形多层支护结构变形规律;5)累计变形均控制在设计预留变形量内,保证了该隧道岭脊核心段大变形控制效果。     

A receding horizon sliding control approach for electric powertrains with backlash and flexible half-shafts

Active control of electric powertrains is challenging, due to the fact that backlash and structural flexibility in transmission components can cause severe performance degradation or even instability of the control system. Furthermore, high impact forces in transmissions reduce driving comfort and possibly lead to damage of the mechanical elements in contact. In this paper, a nonlinear electric powertrain is modelled as a piecewise affine (PWA) system. The novel receding horizon sliding control (RHSC) idea is extended to constrained PWA systems and utilised to systematically address the active control problem for electric powertrains. Simulations are conducted in Matlab/Simulink in conjunction with the high fidelity Carsim software. RHSC shows superior jerk suppression and target wheel speed tracking performance as well as reduced computational cost over classical model predictive control (MPC). This indicates the newly proposed RHSC is an effective method to address the active control problem for electric powertrains.     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

超高压共轨系统轨压控制策略研究

为稳定控制超高压共轨系统中的共轨腔压力并缩短轨压控制算法的开发周期,利用AMESim/Simulink联合仿真技术建立了超高压共轨系统轨压控制仿真模型,采取前馈+PID控制算法设计了轨压控制策略,并针对轨压控制中的瞬态和稳态工况进行了仿真计算,最后在试验台架上开展了轨压跟随性测试。结果表明:所制定的前馈+PID控制算法能使轨压稳定在目标轨压附近,上下波动小于3 MPa,且轨压突变时瞬态响应时间小于0.5s,控制结果能够满足超高压共轨系统对精度和速度的需求。     

柴油机气门导管断裂影响因素分析及改进

针对某柴油机气门导管在整机台架试验过程中发生的横断和纵裂失效故障,对气门导管的材料性能、结构应力、微动磨损、热变形、装配工艺等影响因素进行了分析。分析结果表明:材料力学性能差和装配过盈量较大造成的应力集中和微动磨损是气门导管横断的主要原因;液氮人工压装的装配工艺是造成气门导管纵裂的主要原因。据此提出新方案气门导管,并通过了整机台架试验验证。     

现代大学生公寓电气设计浅析

文章采用文献资料、归纳与综合、专家访谈等研究方法,对现代大学生公寓电气设计进行了系统研究,主要内容包括配电系统、负荷系统、防雷接地、消防系统和智能化五个方面,旨为大学生公寓的电气设计提供有益资讯．     

高等教育大众化视阈下的高等职业教育质量观刍议

随着我国高等教育大众化进程的不断推进,高等职业教育的教育质量成了全社会最为关注的问题．文章运用高等教育理论并结合当前高等职业教育发展的现状,对新时期高等职业教育质量现进行了导引性研究,旨在为目前高等职业教育的发展挖掘和提供多雏视角．     

基于模糊PID控制的ABS仿真研究

以车轮滑移率为控制对象,分析了模糊控制的理论基础,将传统的模糊控制与经典的PID控制相结合,提出了白适应模糊PID控制算法,并进行了仿真研究.