半透空沉箱式防波堤的消波性能试验研究

提出一种新型防波堤——半透空沉箱式防波堤。在玻璃水槽中进行系列水工模型试验,量测在不同波高、周期波浪作用下,半透空沉箱防波堤前后的波浪特征参数,分析半透空沉箱防波堤对不同特征波浪的反射率,波浪周期与波浪尖锐度之关系。探讨该防波堤结构的消波原理与性能,根据试验分析结果,选出最优的透空率及内置斜坡坡度,试验结论可为开敞式港区码头的防波消波方案设计与规划提供一种新思路。     

透空式防波堤透浪的数值模拟

基于FLUENT求解器,以N-S方程为控制方程,采用动量源方法及追踪自由面的VOF方法,建立了同时具有造波和消波功能的数值波浪水槽。利用该数值水槽对透空堤的透浪、越浪问题进行数值模拟,并与物理模型试验进行比较,结果表明:数值模拟能较好地复演防波堤越浪、透浪过程。     

玻璃钢防腐蚀材料检测方法

针对海洋环境下混凝土结构易遭受海水侵蚀导致结构破坏、而高性能混凝土等技术措施不能满足高耐久技术要求的现状,采用玻璃钢包覆防腐蚀技术以提高海工混凝土结构耐久性。对玻璃钢包覆防腐蚀材料的原材料和耐久性检测方法进行分析,提出原材料和耐久性检测方法,以利于玻璃钢防腐材料施工质量的控制。     

超临界雷诺数下桥墩紊流宽度的计算方法

桥墩紊流宽度的计算与水流雷诺数的范围关系较大,将影响到计算成果的合理性。结合山区河流超临界雷诺数条件,采用格子Boltzmann方法模拟桥墩三维紊流流场,并结合大涡模拟和运动边界处理方法,分析不同来流、河形等条件下的桥墩三维紊流宽度,由此建立了顺直河道和弯曲河道中圆型桥墩相对紊流宽度与弗劳德数之间的耦合关系。该研究成果通过四川邓家坝大桥航宽验算,与经验法及祖小勇算法比较,发现该方法得出的桥墩紊流宽度略小、其数值趋于合理。     

多体浮式防波堤消波特性数值模拟

多体浮式防波堤消波特性是决定其应用价值的重要因素,基于三维势流理论,通过使用Ansys Workbench软件和AQWA Graphical Supervisor(AGS)图像后处理软件,对多体浮式防波堤在不同入射角和浮筒吃水深度下的消波效果展开研究。结果表明,在入射角度为90°时,多浮筒浮式防波堤能够最大程度地消减波浪。同时,透射系数随吃水深度的增加而不断减小,但结构稳定性会下降。因此,实际工程中应尽量保证浮式防波堤的迎浪面与波浪的来波方向垂直,这样可以获得较好的消波效果,同时应尽量避免选择吃水深度过大的浮式防波堤。     

Model Test on Grouting Law in Dynamic Water-Rich Sand Layers by the Electric Resistance Method北大核心CSCD

In order to study the diffusion law of grouting slurry in the water-rich sand layer under flowing water conditions, a grouting test model consisting of a main test system, a grouting system, and a measurement system was developed. And for detecting the diffusion scope of the grouts, a new resistivity method was proposed. It is found that the relationship between grouting pressure and grouting rate during the test is strong. Under hydrodynamic conditions, the grouting slurry diffuses elliptically. Due to gravity and the effect of the upper water flow, the center of gravity of the ellipsoid is below the grouting outlet, and the grouting effectively improves the physical and mechanical properties of water-rich sand bodies. At the same time, the resistivity method has a good application effect on the detection of grouting diffusion range. The range of slurry diffusion obtained by the resistivity method is basically consistent with the boundary of the stone body after excavation, indicating that the resistivity method is reliable for detection of grouting range in dynamic water-rich sand layer. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Back-Calculation of Ground Stress Field and Rockburst Analysis for Wunvfeng Tunnel北大核心CSCD

Studying the in-situ stress distribution at a tunnel site is very important to determine surrounding rock characteristics, the engineering design and the construction scheme. By using the multiple linear regression method based on the least square algorithm, the initial geostress field is analyzed and the corresponding regression coefficients are obtained. The ground stress obtained from the proposed back analysis is reasonable and can meet the demands of the engineering applications. From the rockburst risk level distribution diagram, it is speculated that the Wunvfeng tunnel is in the high filed stress area. Field monitoring should be strengthened and emergency plans should be made to cope with the rockburst risks during the construction process. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis of Ground Response and Structure Stress Induced by PBA Method北大核心CSCD

The application of prefabricated tunnel technology has been become a new research field both in China and abroad. Based on the running tunnel between Yufuhe station and Wangfuzhuang station of Jinan rail transit line R1, a new prefabricated tunnel construction technology, the PBA method is presented. This paper makes a detailed discussion on section form, supporting scheme and construction process of the PBA method. In this study, 3D a new 3D numerical model for PBA method is presented by finite difference numerical simulation software Flac and the construction processes are modeled. The rule of ground surface settlement, ground deformation and structural stress caused by PBA method is studied in detail. Results show that the structure of PBA method can effectively control the deformation magnitude and scope. Stress concentration appears at the prefabricated connection parts and the reinforcement needs to check. The total assembled structure forms the load-bearing system after the completion of the lateral wall. The built-in depth of the precast pile and pile bottom grouting quality should to be ensured to control the displacement of the precast piles. The results of this study will be a useful reference for similar projects in the future. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Effect of Explosion in a Gas Pipeline Compartment of a Utility Tunnel on Neighboring Metro Tunnels北大核心CSCD

In this paper the numerical simulation analysis of the effect of explosion in the gas pipeline compartment of a utility tunnel on neighboring metro tunnels was conducted using the software AUTODYN. The results show that the TNT equivalent in a fireproof partition with length of 200 m is 41.6 kg when the gas concentration in the gas pipeline compartment reaches 10%; the blast wave has much effect on the crown and arch waist of the round metro tunnel and it’s necessary to take some protective measures in both areas; when the surrounding soil is sand, the utili- ty tunnel is above the round metro tunnel and their alignments are in the same direction, the greater the vertical spacing between the utility tunnel and the metro tunnel, the smaller the effect of the blast wave on the metro tunnel; when the vertical spacing is 7.2 m, the maximum dynamic tensile stress is 1.86 MPa (including the static stress value of 1 MPa in the tunnel segment) and it is slightly smaller than the designed tensile strength of metro tunnel (about 1.89 MPa). The maximum vibration velocity and the maximum displacement meet the structural stability require- ments, so it is suggested the vertical spacing between the utility tunnel and metro tunnel shall not be less than 7.2 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

逆向支撑底模反吊在水中防撞墩台施工中的应用

在航道整治工程中设置的桥梁防撞墩,由于墩台的底部经常设置在常年平均水位之下,无法按常规方法采用底部模板正向支撑系统施工。通过采用逆向支撑底模反吊方案,将钢木组合整体模板吊装入水,墩台分层浇筑的方式进行施工。该方案无需设置围堰,形成干地施工条件,成功解决水下混凝土浇筑和模板拆除难的问题,也解决通航水域狭小、操作空间有限、保证正常通航的问题,具有施工方便、安全性高、墩台施工精度易于控制的优点。