基于改进型消灭曲线法的横摇阻尼估算

自由衰减试验仍是目前最为有效且常用的估算横摇阻尼系数的方法.横摇阻尼系数的估算精度对于船舶横摇运动的预报起着至关重要的作用.通常采用所谓的消灭曲线法来分析自由横摇衰减数据.该方法的一个不足之处在于其推导是基于忽略了非线性恢复力项的自由横摇运动方程.另一方面,考虑更多非线性成分的能量法能够纳入该因素影响但在实施过程中较为复杂.文中提出了一种改进型的消灭曲线法,能够纳入船体非线性恢复力项的影响.所提出的方法形式简单且相比能量法更易于实施.数值试验证明了改进型消灭曲线法的正确性,并展现了其相对传统消灭曲线法所具有的优势.     

Airport capacity increase via the use of braking profiles

Many airports are encountering the problem of insufficient capacity, which is particularly severe in periods of increased traffic. A large number of elements influence airport capacity, but one of the most important is runway occupancy time. This time depends on many factors, including how the landing roll procedure is performed. The procedure usually does not include the objective to minimize the runway occupancy time. This paper presents an analysis which shows that the way of braking during landing roll has an essential impact on runway throughput and thus on airport capacity. For this purpose, the landing roll simulator (named ACPENSIM) was created. It uses Petri nets and is a convenient tool for dynamic analysis of aircraft movement on the runway with given input parameters and a predetermined runway exit. Simulation experiments allowed to create a set of nominal braking profiles that have different objective functions: minimizing the runway occupancy time, minimizing noise, minimizing tire wear, maximizing passenger comfort and maximizing airport capacity as a whole. The experiments show that there is great potential to increase airport capacity by optimizing the braking procedure. It has been shown that by using the proposed braking profiles it is possible to reduce the runway occupancy time even by 50%.     

基于地基回弹因素的盾构隧道管片上浮预测

针对软弱地层盾构隧道管片脱出盾尾后出现的上浮问题,分析盾构施工过程中管片上浮的诱因,得出软弱地层中管片的上浮主要是地层应力重分布产生的地基回弹力引起的。在此基础上建立隧道开挖动态模型,分析隧道上浮量变化规律以及地层特性对管片上浮量的影响规律,得出地层弹性模量和管片上浮量呈一定的指数关系,且弹性模量对管片上浮量的影响远大于地层黏聚力和内摩擦角。通过力平衡理论计算盾构开挖引起的地层回弹力、管片上浮量以及隧道上浮影响的地层高度范围,并通过对珠江狮子洋工程管片上浮量的计算与实测对比,证明该公式的合理性,为盾构隧道工程中考虑地基抗力引起的管片上浮量预测提供一种新的方法。     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Sensitivity analysis of parameters for multi-stand roll forming using a new booting model

Multi-stand roll forming is a process that has very complicated deformation behaviour and shows significant nonlinearity.In this paper, the sensitivity analysis of parameters for multi-stand roll forming was performed via a new booting finite element method(FEM) model.Compared with the most of simulation, the new model is more consistent with production process and can account for the effects of roll rotating speed.Based on the model, the process of an open section channel formed with 10 passes was simulated and the sensitivity analysis was conducted with orthogonal experiment design combined FEM model.The multi-stand roll forming process can be efficiently analyzed by the new booting model.And sensitivity analysis shows the hardening exponent plays an important role in controlling the quality of the products.     

����ʱ�չ켣���ٵĽ�ͨ�����Բ���������

基于视频的交通流检测在智能交通系统中具有重要意义。本文针对广泛采用的低位摄像机,提出了一种交通流特性参数的检测分析方法。首先基于三级虚拟检测线和自适应更新率局部背景建模来快速提取车辆特征点并消除活动阴影对提取精度的影响;然后基于Adaboost（Adaptive Boosting,自适应增强）分类器实现特征点按车分组,并在跟踪过程中根据运动特征相关度消除分组误差,获取高精度的车辆轨迹;进而自动生成多车道轨迹时空图并提取各车道交通流的多种特性参数。实验结果验证了算法的高效性;同时,自动生成的多车道轨迹时空图也为更多的交通信息获取和更深入的交通流特性分析提供了有力支持。     

抽气式涡轮帆的气动力学分析研究

介绍了抽气式涡轮帆的结构和工作原理,使用Gambit软件建立了涡轮帆的模型,并采用RNG k-ε湍流模型描述了涡轮帆的动力学特性。利用Fluent软件对抽气式涡轮帆进行了数值模拟计算,并与风洞试验数据进行了对比,升阻力系数的模拟结果与试验数据变化趋势基本一致。计算了特定情况下椭圆筒不同偏转角时的升阻力系数,并模拟了不同旋转角下吸气强度以及旋转角为0°时分流板位置对涡轮帆升阻力系数的影响,为涡轮帆的优化选择提供了依据。     

新型沙漏式FPSO的浮体外形参数对水动力性能的影响

为了解决传统船型和已有圆柱筒状FPSO的性能局限,论文提出了一种具有沙漏型浮式主体的新概念FPSO。根据所研发的新型沙漏式浮体模型,确定了能够反映浮体几何形状、FPSO基本功能和水动力性能的5个相互独立的外形参数。然后,采用基于频域势流理论的边界元数值模拟方法研究了新型沙漏式浮体在波浪中的运动响应,并且定性分析了不同浮体外形参数(下倾角、水线面半径等)对浮体水动力性能的影响,得到一些有意义的结论,以期能够为新型沙漏式FPSO的主浮体外形设计提供参考依据和准则。     

浅谈大型门座起重机整机运输及滚装上岸的安全管理

大型门座起重机整机运输及滚装上岸过程存在很大的风险,本文以滨海港北区10万t级通用码头一期工程为例,探讨了大型门座起重机整机运输及滚装上岸的安全管理。     

带落角约束的变结构三维末制导律设计

分析导弹与目标水面舰艇之间三维空间的相对运动特性,并在此基础上进行带落角约束的变结构制导律设计。该制导律设计中,针对一次设计时切换面导数形式过于复杂的情况,作出变换进行二次设计,极大地简化模型;另外,由于目标信息难以获取,故将其视为扰动;最后通过数值仿真验证了所设计制导律的可行性和有效性,具有一定的工程应用价值。