Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

Tuning of transfer functions for analysis of wave–ship interactions

Transfer functions are often used together with a wave spectrum for analysis of wave–ship interactions, where one application addresses the prediction of wave-induced motions or other types of global responses. This paper presents a simple and practical method which can be used to tune the transfer function of such responses to facilitate improved prediction capability. The input to the method consists of a measured response, i.e. time series sequences from a given sensor, the 2D wave spectrum characterising the seaway in which the measurements are taken, and an initial estimate of the transfer function for the response in study. The paper presents results obtained using data from an in-service container ship. The 2D wave spectra are taken from the ERA5 database, while the transfer function is computed by a simple closed-form expression. The paper shows that the application of the tuned transfer function leads to predictions which are significantly improved compared to using the transfer function without tuning.     

考虑横向漂移的船舶路径跟踪自抗扰控制

针对船舶运动系统中内部动态不确定和外部干扰等问题,进行了欠驱动船舶路径跟踪的自抗扰方法研究。利用Backstepping设计参考航向角,并通过线性扩张状态观测器对流干扰和横向运动引起的横向漂移进行估计。其次,根据自抗扰算法对航向进行控制,采用线性扩张状态观测器对外界干扰及内部不确定项进行估计。最后仿真结果表明,在风流干扰下所设计的控制器仍能使船准确地跟踪上参考路径,验证了所提控制方案的有效性。     

基于AR模型的并靠两船相对运动预报研究

根据两船相对运动的特点,利用两船模相对运动的测量数据,运用基于自回归模型的时间序列分析法,建立了两船相对运动的数学模型,并给出了运动姿态的预报值.通过本方法的研究,可以得到满意的相对运动预报精度,为两船补给波浪、补偿装置的开发打下了理论基础.     

两船并靠状态下的运动响应数值模拟研究

针对两船并靠工况复杂,各种运动相互间存在耦合的情况,基于三维势流理论和波浪的辐射/衍射理论,应用多体水动力学软件,建立了船体、护舷和缆绳的模型,开展了两船在风、浪、流作用下的运动响应数值模拟。模拟结果可作为并靠方案设计和优化的参考依据,也可为两船并靠状态下的护舷力学性能计算提供支撑。     

基于改进型消灭曲线法的横摇阻尼估算

自由衰减试验仍是目前最为有效且常用的估算横摇阻尼系数的方法.横摇阻尼系数的估算精度对于船舶横摇运动的预报起着至关重要的作用.通常采用所谓的消灭曲线法来分析自由横摇衰减数据.该方法的一个不足之处在于其推导是基于忽略了非线性恢复力项的自由横摇运动方程.另一方面,考虑更多非线性成分的能量法能够纳入该因素影响但在实施过程中较为复杂.文中提出了一种改进型的消灭曲线法,能够纳入船体非线性恢复力项的影响.所提出的方法形式简单且相比能量法更易于实施.数值试验证明了改进型消灭曲线法的正确性,并展现了其相对传统消灭曲线法所具有的优势.     

Airport capacity increase via the use of braking profiles

Many airports are encountering the problem of insufficient capacity, which is particularly severe in periods of increased traffic. A large number of elements influence airport capacity, but one of the most important is runway occupancy time. This time depends on many factors, including how the landing roll procedure is performed. The procedure usually does not include the objective to minimize the runway occupancy time. This paper presents an analysis which shows that the way of braking during landing roll has an essential impact on runway throughput and thus on airport capacity. For this purpose, the landing roll simulator (named ACPENSIM) was created. It uses Petri nets and is a convenient tool for dynamic analysis of aircraft movement on the runway with given input parameters and a predetermined runway exit. Simulation experiments allowed to create a set of nominal braking profiles that have different objective functions: minimizing the runway occupancy time, minimizing noise, minimizing tire wear, maximizing passenger comfort and maximizing airport capacity as a whole. The experiments show that there is great potential to increase airport capacity by optimizing the braking procedure. It has been shown that by using the proposed braking profiles it is possible to reduce the runway occupancy time even by 50%.     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Sensitivity analysis of parameters for multi-stand roll forming using a new booting model

Multi-stand roll forming is a process that has very complicated deformation behaviour and shows significant nonlinearity.In this paper, the sensitivity analysis of parameters for multi-stand roll forming was performed via a new booting finite element method(FEM) model.Compared with the most of simulation, the new model is more consistent with production process and can account for the effects of roll rotating speed.Based on the model, the process of an open section channel formed with 10 passes was simulated and the sensitivity analysis was conducted with orthogonal experiment design combined FEM model.The multi-stand roll forming process can be efficiently analyzed by the new booting model.And sensitivity analysis shows the hardening exponent plays an important role in controlling the quality of the products.     

FLNG总体设计关键技术研究

阐述了集天然气预处理、液化、储存、外输为一体的新型海上浮式装置FLNG总体设计中的几项关键技术。提出控制船体运动性能的重要性,从主尺度选择、线型设计和典型配载工况等方面入手进行分析,确定250,000m3 FLNG船体主尺度,以确保上部生产系统高效率的正常作业。针对LNG货物围护系统,提出薄膜型(双排舱)和SPB独立舱型两种货物围护系统方案,并从上部模块支墩设置和隔离舱加热等方面对这两个方案进行比较。论述FLNG冷却海水供应系统的特点及其与常规海底门取水方法的不同之处,提出舷外海水提升泵取水的可行方案。