Assessment of the volume of fluid method for free-surface wave flow

This study was concerned with the free-surface wave flow around a surface-piercing foil. The volume of fluid method implemented in a Navier–Stokes computational fluid dynamics code was employed. Three widely used discretization schemes for the volume of fluid method were assessed for a test case that involved general ship waves, spilling breaking waves in front of the leading edge, and bubbly free surfaces in separated regions. A single computational approach was selected for the comparison, and a grid-dependence study was carried out. The computational results were validated against existing experimental data, showing good agreement. The validation results suggest that all three discretization schemes perform well, but the best and most efficient results were obtained using the high-resolution interface capturing scheme.     

桥梁维修加固计算机系统框架研究

基于开发的桥梁维修加固计算机系统应用规范和荷载试验评定标准,通过采集的数据建立评价数据模型和决策数据模型,可对桥梁的损伤状况和承载能力作出评价,并通过专家咨询法给出损伤原因和决策措施,对类似工程具有一定的参考价值。     

Analysis on Ground Surface Deformation and Influence of Construction Parameters Caused by Two Different Shield Machines in Double-tube Tunnelling北大核心CSCD

Based on a shield-driven running tunnel project of Hangzhou Metro Line 2, this paper carries out field measuring of the ground surface deformation caused by two different shield machines in double-tube tunnelling in soft soil areas, obtains the laws of the surface deformation caused by shield-driven double-tube tunnelling and verifies the applicability of the modified Peck formula to double-tube tunnelling. The results show that in soft soil areas the impacts on ground surface deformation caused by different shield construction parameters in the previously and subsequently excavated tunnels are different, while the surface deformation changes sharply before and after the shield machine passing through the cutting face, and a rebound phenomenon occurs when the shield tail passes through the cutting face due to the influence of the grouting; The cutterhead torque of the shield machine in soft soil areas can be composed of five calculation factors, and the calculation results are in good agreement with the measured values. The larger the opening rate of the shield cutterhead is, the larger the average torque value will be, the higher the percentage of large ground loss rate will be, and the larger the maximum ground surface settlement will be; The ratio of cutterhead torque T to mucking volume per ring Q is used as the control parameter for analyzing the ground surface settlement, and a certain positive correlation between the ratio and the surface settlement value is determined, the smaller the cutterhead opening rate is, the more accurate the fitting results will be. © 2022, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

膨胀土边坡稳定性分析

以工程实例为背景,对膨胀土边坡浅层滑动的各种内在和外在因素进行分析,提出膨胀土边坡的设计原则,可为同类工程提供一定的参考。     

岸边起重机结构表面防腐涂料的发展趋势

良好的表面防腐涂装对保证岸边起重机金属结构长期安全有效工作十分重要。以氟碳面漆取代聚氨酯面漆,可显著提高漆面的耐久性、耐候性、耐腐蚀性,并具有优异的自清洁性和耐冲刷性。要保证氟碳面漆的优异性能,必须选用合适的树脂原料、颜料、溶剂和助剂,并在涂料的生产和涂装施工过程中严格执行工艺要求。     

水基型沥青清洗剂的研究

采用表面活性剂复配技术,经基质材料的性能对比及正交试验分析,开发出能在常温下迅速除去金属表面沥青且环保的水基型清洗剂;进一步,论文探讨了清洗方式、浸泡温度、清洗剂浓度以及浸泡时间等因素对金属表面清洗效果的影响,证实了该清洗剂良好的净洗力,验证了研发的清洗剂作为道路工程界传统沥青清洗剂替代品的可行性.     

多种破坏因素下舰船电力系统三维战损综合评估

分析武器攻击产生的4种主要破坏因素对设备的损伤机理,对船体和电力系统进行三维数字建模,采用Matlab编程进行蒙特卡罗模拟多种常规武器攻击。考虑多种破坏因素,提出武器多次命中时电力系统各部分损伤概率和损伤等级的计算方法。利用层次分析法确定权重,综合评估电力系统的损伤,提出电力系统的设计及防护建议。     

在冷镦机下模芯内成型螺栓倒角

通过改进模具结构,在冷镦机上成型螺栓倒角,替代机械加工,提高生产效率,降低生产成本。     

浅埋隧道下穿既有铁路爆破施工方法

结合工程实例，介绍了浅埋软弱地层条件下穿越既有铁路双连拱隧道的爆破开挖方案设计、爆破振动控制方法以及爆破振动监测等安全技术措施。     

Numerical simulation of wave-induced nonlinear motions of a two-dimensional floating body by the moving particle semi-implicit method

The moving particle semi-implicit (MPS) method was applied to compute nonlinear motions of a floating body influenced by the water on deck. To compute the motions of a rigid body, the fluid pressure at the position of each particle on the body surface was directly integrated in space and the equations of translational and rotational motions were integrated in time to determine the correct position of the rigid-body surface at each time step of the time-domain calculation. The performance of this method was validated through a comparison with measured results in an experiment that was newly conducted using a model of a box-shaped floating body with a small freeboard. Although the overall agreement was good, some discrepancies were observed for a shorter wave period, especially for the drift motion in sway. The effect of numerical resolution on the results was checked by changing the number of particles. With a higher number of particles, no obvious improvement was seen in the global body motions, but the resolution of the local free-surface profile, including the water on deck, was improved.