大断面异形盾构隧道弯矩传递系数原型加载试验研究

由于异形盾构隧道特殊的结构断面型式,管片设计暂无相关规范可循,故基于原型三环管片力学加载试验对异形盾构管片环向接头弯矩传递系数进行研究,研究结果表明:1)随埋深增加,异形盾构管片结构整体刚度提升,但由于各接头刚度与相邻管片结构刚度比随埋深增加变化规律不一致,异形盾构管片接头弯矩传递能力呈部分减弱部分增强的现象;2)同埋深条件下,随着侧压力系数的增加,除右拱腰处接头外,其余接头弯矩传递能力随着接头刚度与相邻管片结构刚度比的增大而逐渐增强;3)随着埋深增加,各接头弯矩传递能力对侧压力系数的敏感程度逐渐减弱;4)极限破坏后,异形盾构管片内外弧面裂缝的分布规律证明了明显的弯矩传递现象。     

新型沙漏式FPSO的浮体外形参数对水动力性能的影响

为了解决传统船型和已有圆柱筒状FPSO的性能局限,论文提出了一种具有沙漏型浮式主体的新概念FPSO。根据所研发的新型沙漏式浮体模型,确定了能够反映浮体几何形状、FPSO基本功能和水动力性能的5个相互独立的外形参数。然后,采用基于频域势流理论的边界元数值模拟方法研究了新型沙漏式浮体在波浪中的运动响应,并且定性分析了不同浮体外形参数(下倾角、水线面半径等)对浮体水动力性能的影响,得到一些有意义的结论,以期能够为新型沙漏式FPSO的主浮体外形设计提供参考依据和准则。     

Water Wave Scattering by a Nearly Circular Cylinder Submerged Beneath an Ice-cover

Assuming linear theory, the two-dimensional problem of water wave scattering by a horizontal nearly circular cylinder submerged in infinitely deep water with an ice cover modeled as a thin-elastic plat...     

T型接头横向埋藏裂纹扩展特性

基于断裂力学理论和有限元分析,研究T型接头横向埋藏裂纹扩展特性,实现了双向拉伸载荷作用下T型接头横向埋藏裂纹扩展形状变化的数值模拟。结果表明:T型接头横向埋藏裂纹扩展至结构表面时的形状为近圆形,与裂纹埋藏位置和初始形状无关;埋藏于焊趾端部板材中的裂纹扩展快于埋藏于焊缝中的裂纹扩展。     

复合材料船舶帽型加筋结构静力分析

分析不同截面形状和不同铺层方案对复合材料帽型加筋结构最大位移的影响。分别采用Beam188,Beam189,Shell99单元模拟矩形截面帽型加筋梁结构,结果显示建立整船模型时可以采用梁单元代替壳单元模拟复合材料帽型加筋梁的方法来简化建模。同时还研究不同铺层、不同铺设角、不同截面形状对帽型骨材每一层等效应力的影响,为复合材料船舶帽型加筋结构的计算和设计提供参考。     

简支变连续梁法加固多跨T梁桥效应分析

多跨简支T梁变连续加固措施是多跨简支T梁桥加固改造、提高承载能力的行之有效的方法.但实践中发现该方法存在着一定的问题.以跨径为16.76m+16.76m的两跨简支T梁为例,通过理论分析计算表明,该方法在提高跨中抗弯承载能力的同时,却降低了中间支点处梁的抗剪承载能力.建议在采用此方法加固多跨简支T梁的同时应对中间支点梁的抗剪能力进行加固.     

大跨悬索桥主缆线形解析迭代法研究

基于悬索桥在恒载作用下的受力特点,建立了主缆线形控制计算的解析迭代方法,以此确定主缆无应力长度、成桥线形、空缆线形。算例结果表明该解析法具有适合程序计算、收敛速度快、计算精度高的特点,可用于悬索桥设计与施工控制计算。     

基于粒子群算法的水下多元线阵阵形有源校正方法

针对存在阵元位置误差的水下多元线阵,提出一种基于粒子群优化算法的远场有源阵形校正方法.该方法选用2个辅助源分时工作方式,利用无条件最大似然方位估计算法构建目标函数,并通过粒子群算法对阵元位置进行寻优.利用该方法对均匀线阵进行性能仿真实验.结果表明:该方法稳健性好、校正精度高,具有一定的应用前景.     

Database of sail shapes versus sail performance and validation of numerical calculations for the upwind condition

A database of full-scale three-dimensional sail shapes is presented with the aerodynamic coefficients for the upwind condition of International Measurement System (IMS) type sails. Three-dimensional shape data are used for the input of numerical calculations and the results are compared with the measured sail performance. The sail shapes and performance were measured using sail dynamometer boat Fujin. This is a boat of 10.3-m length overall in which load cells and CCD cameras were installed to simultaneously measure the sail forces and shapes. At the same time, the sailing conditions of the boat, e.g., boat speed, heel angle, wind speed, and wind angle, were measured. The sail configurations tested were: mainsail with 130% jib, mainsail with 75% jib, and mainsail alone. Sail shapes were measured at several vertical positions for the shape parameters defined by: chord length, maximum draft, maximum draft position, entry angle at the luff, and exit angle at the leech, all of which finally yield three-dimensional coordinates of the sail geometry. The tabulated shape data, along with aerodynamic coefficients, are presented in this article. In addition, numerical flow simulations were performed for the measured sail shapes and the sailing conditions to investigate the capability and limitations of the methods through detailed comparison with the measurements. Two numerical methods were used: a vortex lattice method (VLM) and a Reynolds-averaged Navier–Stokes (RANS)-based computational fluid dynamics method. The sail shape database, in association with the numerical results, provides a good benchmark for the sail performance analysis of the upwind condition of IMS type sails.     

T型焊接接头疲劳性能研究

T型焊接接头在船舶与海洋工程结构中广泛应用,研究T型焊接接头的疲劳性能对于提高船舶与海洋工程结构的强度具有重要意义.针对工程中常用的四种焊趾形式的T型焊接接头,利用有限元计算和模型试验两种方法对其疲劳性能进行了研究.结果表明,平面型焊趾是较优的T型接头焊趾形式.