NFM盾构机带压开舱换刀技术

文章以深圳地铁2号线东延线2222标段工程中采用的带压开舱换刀试行方法为依托,针对NFM土压平衡盾构机的设备情况,总结出了相关的技术方案,主要包括开舱前的准备工作和带压开舱换刀作业的整个实施流程及相关技术要点。     

固结黏土地层盾构直接破除排水板关键技术研究

宁波地铁5号线1期下穿高速公路路基时存在68°斜交长40 m的含塑料排水板的固结黏土地层,为研究盾构直接通过可行性、刀具选型、施工参数优化等问题,利用TBM掘进模态综合试验平台,进行了不同类型刀具、不同掘进参数的固结黏土地层排水板破除试验。研究表明： 对于含排水板的固结黏土地层,在合理选择刀具、盾构参数并优化掘进参数情况下,盾构法施工直接破除基本可行,试验为宁波地铁工程建设提供了依据,也可为类似工程设计及施工提供参考。     

软土地区盾构施工对既有单桩工作性状的影响分区研究

为研究既有桩基位于拟建隧道周围不同位置时,隧道开挖对桩基产生的受力与变形规律,依托天津地铁3号线北站至铁东路站左线盾构区间项目,利用ABAQUS软件将隧道周围软土按照桩端径向、切向位置的不同划分为8个区,建立考虑软土修正剑桥本构关系的二维有限元模型,探讨隧道开挖后桩基分别处于设计荷载和极限荷载下的桩侧摩阻力和桩身位移变化规律,并建立隧道开挖对邻近单桩工作性状的影响分区。计算结果表明： 1）隧道开挖会使桩基近隧道侧产生负摩阻力,负摩阻力最大值随桩到隧道径向距离的减小而逐渐增大,随桩长的增大而逐渐增大; 2）隧道开挖会导致桩身极限侧摩阻力降低,当桩端位于隧道两侧分区时降幅较大,在10%~15%; 3）桩端分别位于隧道两侧、底部、顶部分区时,依次对桩身倾斜率、桩身挠曲变形和桩顶沉降的影响最显著; 4）提出能够对隧道开挖后既有单桩工作性状分区进行评价的指标,当桩端位于3区时,盾构隧道开挖造成单桩的综合影响程度最大,应加强施工监控措施。     

盾构法联络通道密封垫设计及防水试验研究

为探究适合盾构法联络通道工程的密封垫断面形式,以宁波市轨道交通3号线第1条盾构法联络通道为工程背景,针对遇水膨胀橡胶设计阴阳凹凸、圆形孔洞、梳形、矩形等4类断面。对各断面形式进行可行性分析,选取阴阳凹凸断面与矩形断面作为初选方案。利用Abaqus/Explicit计算模块对2种断面的接触应力进行有限元分析,通过设计“一”字缝耐水压力试验,验证数值模拟中接触应力较大的矩形断面的防水能力。研究表明： 1）数值模拟结果显示,接触面最大接触应力与平均接触应力均随着张开量的增加而减小; 同等张开量与错台量下,在压缩与膨胀2个阶段中,矩形断面的接触应力均大于阴阳凹凸断面,因此选取矩形断面作为备选方案。2）“一”字缝耐水压力试验结果表明,矩形断面密封垫保压48 h后耐水压力明显提升,且张开量越大耐水压力提升幅度越大。3）综合数值模拟与试验结果可知,该矩形断面密封垫满足0.6 MPa的防水要求。     

压气条件下泥膜进气值测量试验研究

在压气条件下,进气是泥膜透气失效的起始点。为测量并研究泥膜在气压下的进气压力值（进气值）,通过自制的试验装置,在不同压气条件下对3种泥膜进行进气值测量试验。试验结果表明： 1)由闭气排水与固结排水的差值可以辨别泥膜是否进气,得到泥膜进气值; 2)采用泥膜特征孔径D90/2代入推导公式可近似计算泥膜进气值; 3)泥膜在不同压气条件下进气值不同,增压速率越低,泥膜进气值越大; 4)在较快和较慢的增压速率下存在进气值变化趋于稳定的现象,最大进气值为最小值的2倍以上。     

盾构法T接隧道结构受力现场试验研究——以宁波轨道交通3号线联络通道为例

为了了解盾构法T接隧道在施工过程中主隧道外部的荷载以及响应,以国内第一条使用机械法施工的联络通道--宁波轨道交通3号线为背景进行研究。本文通过研究施工过程中的施工工况节点,现场监测主隧道结构的外荷载、收敛变形并计算结构内力,得到在整个施工过程中主隧道的结构响应及其变化规律。通过本文的研究,可以得出以下结论： 1）施工过程可依据外部荷载和结构体系进行划分工况,各工况具有明显的不同响应; 2）始发端和接收端的内力变化主要受到盾构顶力和外部注浆荷载的影响,且主要影响切削侧,切削过程中的内力增量在10%～20%,注浆压力影响的增量部分达到了50%; 3）各环及内支撑轴力增量在200 kN以下,破洞位置导致的轴力损失可以由其余位置共同承担,不需要特殊的破洞阶段超载设计。     

盾构隧道管片接头嵌入式密封垫防水性能探究

为解决传统密封垫易于与混凝土管片胶结处发生渗漏水的问题,对新型嵌入式密封垫的防水性能进行研究。与传统的现场粘贴防水橡胶密封垫的工艺不同,嵌入式密封垫是将密封垫与混凝土管片整浇预制。采用模型试验和有限元数值模拟方法,对隧道接头中嵌入式密封垫的防水能力进行分析和论述。研究结果表明： 文中所涉截面形式的嵌入式密封垫在控制工况,即张开量7 mm、错缝量10 mm的情况下,满足上海深层排水调蓄隧道0.6 MPa的耐水压力要求,且弥补了传统密封垫易从密封垫与混凝土接触面渗漏水的缺陷。此外,通过在密封条两侧设置凹槽,可有效减小密封垫脚部与混凝土间接触应力,减少局部应力集中,保证混凝土管片的完整性,提高接头防水能力。     

Analysis of the Circulation System of a Slurry Shield and the Muck Carrying Ability of a Dredging Pipe北大核心CSCD

The circulation system of a slurry shield is composed of a transportation system and a processing system.For shield construction, correct selection of the circulation system for the slurry shield is directly related to construc-tion speed. Using the Nanjing Yangtze tunnel as an example, the material balance calculation of the circulation sys-tem, sieving effect analysis, and analysis of the muck carrying ability of the dredging pipe are conducted for various strata. The practical results show that above mentioned calculations and analysis method provide a good reference for the proper selection of a slurry separation system and dredge pipe. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Effects of Overloading on the Mechanical Properties of Tunnel Structures in the Silty Ground --A Case Study of Sutong River-crossing GIL Utility Tunnel北大核心CSCD

Based on the Sutong GIL utility tunnel project, which is constructed by the shield machine under the river, and as for the overloading problem at the river bank slope during operating period, the refined threedimensional finite element model was established to study the deformation and cracking characteristics of the tunnel segment structure under different forms of overloading. The evolution laws of section convergence, joint opening and structural stress were analyzed, and the structure damage mechanisms were revealed under conditions of large area loading and local loading. The surface-surcharge control standard was proposed. For the big diameter shield tunneling crossing the silty clay, the research results show that: (1) the deformation failure process is divided into three stages under large area loading condition, taking the design load and compressive yield of rebars inside haunch as the critical points respectively. The first stage is characterized by the elastic stress, the second stage is in plastic state with fracture, and the third stage is accelerating deformation and instability stage. The vertical convergence is 110.5 mm with no opening of joints when rebars are yielded; (2)the deformation failure process under local loading condition is also divided into elasticity, plasticity and instability stages, taking the design load and tensile yield of rebars outside haunch as the critical points respectively. The vertical convergence is 152.6 mm with joint opening of 4.36 mm; (3) the early-warning values of additional stress on the ground under conditions of large area loading and local loading are 110 kPa and 70 kPa respectively. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Soil Body Deformation Caused by Construction of a Double-Line Shield Tunnel with Multiple Factors北大核心CSCD

Considering the influence of many factors (soil loss, frontal additional thrust, the friction force of the shield shell and the additional grouting force), a method for improving the uniform soil body movement model is pro-posed, and a mechanical calculation model is established to study the calculation method for soil body deformation caused by double-line parallel shield driving. Based on the Mindlin solutions of elastic mechanics, the theoretical solutions for soil body deformations caused by the last three factors are calculated; considering the uniform soil body movement model, the theoretical solutions for soil body deformations caused by soil loss are calculated, then the to-tal theoretical solutions for soil body deformations under multiple factors are obtained by means of superposition. The vertical surface settlement, vertical horizontal displacement, and vertical displacements of the soil body at different depths of Hangzhou Metro Line 1 are calculated to analyze the variation laws. Meanwhile the influential factors for horizontal displacement variation are studied. The research shows that with a change of depth, the settlement of the soil body changes within the scope of 10 to 13 m in the horizontal direction near where the maximum settlement occurs;the direction of the horizontal displacement of the soil body changes with a change of the positional relationship be-tween the calculation points and the tunnel; and with an increase of interval J for the two tunnels, the horizontal dis-placement of the soil body of a deep double-line tunnel decreases while the displacement near the surface changes slightly. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.