快速重载运输趋势下的城轨车辆技术发展特征

随着城市化的进程,城轨交通客流强度不断增大,发车间隔不断压缩,使得我国城轨交通呈现出快速、重载、智能的发展趋势。文章结合我国目前城轨车辆快速、重载的发展状况,提出城轨车辆最大轴重的概念和建议值,且应按最大轴重对承载结构件进行设计,详细分析了城轨车辆结构件的技术发展特征,并建议应及时检测和维护车轮和钢轨,降低车、轨的振动和噪声,以提高车、轨的综合使用寿命。     

地铁隧道二次衬砌钢筋网防裂性能研究

为了定量分析防裂钢筋网提高隧道衬砌结构抗裂性能的机理和幅度,以地铁双线隧道二次衬砌结构为研究对象,采用荷载结构法和杆系有限元数值模拟方案,定量分析二次衬砌结构不设置与设置钢筋网这2种情况下的开裂临界荷载。其中素混凝土结构以达到极限拉应变为临界状态,衬砌结构增设钢筋网后以达到GB 50157-2013《地铁设计规范》允许的最大裂缝宽度0.2mm为临界状态。分析结果表明,配置防裂钢筋网后,Ⅲ级和Ⅳ级围岩衬砌结构抗裂性能可分别提高22.4%和19.3%,Ⅴ级围岩衬砌结构抗裂性能提高15.2%;Ⅲ级和Ⅳ级围岩二次衬砌结构的破坏形式由脆性破坏变为延性破坏,从而提高了其安全性能。     

无线调车机车信号和监控系统实际应用中无线通信解决方案研究

在配有无线调车机车信号和监控系统(STP)的铁路车站,如果站场存在高建筑物、山体、多隧道、特长隧道等特殊情况,会使车地无线通信出现信号弱或者无信号现象。针对这些特殊站场情况,给出几种无线通信解决方案,并在实际工程项目中有效地解决信号弱或者无信号问题。     

内压载荷下X80管道裂纹应力分布规律研究

为了研究内压作用下管道裂纹应力场分布规律,以含有表面裂纹的X80管道为研究对象,对不同形状、不同方向、不同内压、不同尺寸的含裂纹管道进行仿真分析和实验验证。结果表明:裂纹尖端处应力远大于裂纹中心应力。裂纹形状对应力影响作用较小,随着裂纹方向与管道轴向夹角增大,裂纹尖端应力先增大后减小,随着管道内压、裂纹深度、裂纹长度的增大,裂纹尖端处应力随之线性增大。其中,裂纹长度对裂纹尖端应力的影响小于管道内压和裂纹深度。     

STX1(2)型驮背多功能运输车超偏载检测标准

分析了STX₁₍₂)型驮背多功能运输车对既有超偏载检测方法和标准的适应性,提出了该车的超偏载检测方案,明确了公路货车或半挂车超偏载的检测方法及评判标准。     

动车组单车调试工艺及发展趋势

对动车组传统单车调试工艺进行了总结对比,阐述了以智能调试系统、数字化平台为基础的自动化调试原理.重点介绍了智能单车调试设备、智能端部模拟器和移动控制终端,分析了单车智能调试技术的发展趋势.     

Validation and application of nonlinear hydrodynamics from CFD in an engineering model of a semi-submersible floating wind turbine

Nonlinear hydrodynamics play a significant role in accurate prediction of the dynamic responses of floating wind turbines (FWTs), especially near the resonance frequencies. This study investigates the use of computational fluid dynamics (CFD) simulations to improve an engineering model (based on potential flow theory with Morison-type drag) by modifying the second-order difference-frequency quadratic transfer functions (QTFs) and frequency-dependent added mass and damping for a semi-submersible FWT. The results from the original and modified engineering models are compared to experimental data from decay tests and irregular wave tests. In general, the CFD results based on forced oscillation tests suggest increasing the frequency-depending added mass and damping at low frequencies compared to first order potential flow theory. The modified engineering model predicts natural periods close to the experimental results in decay tests (within 5%), and the underprediction of the damping is reduced compared to the original engineering model. The motions, mooring line tensions and tower-base loads in the low-frequency response to an irregular wave are underestimated using the original engineering model. The additional linear damping increases this underestimation, while the modified QTFs based on CFD simulations of a fixed floater in bichromatic waves result in larger difference-frequency wave loads. The combined modifications give improved agreement with experimental data in terms of damage equivalent loads for the mooring lines and tower base.     

Fitness-for-purpose assessment of cracked offshore wind turbine monopile

In this paper, the procedure for flaw acceptability assessment is examined through a case study of a semi-elliptical surface crack in an offshore monopile as it grows till it forms a through thickness crack. Using the procedure prescribed in an industrial standard (BS 7910), the fracture ratio, K_r is shown to increase monotonically with increasing crack depth. The load ratio, L_r, is initially insensitive to the crack depth. However, there is a rapid increase in L_r when the crack depth to thickness ratio exceeds 80%. L_r values obtained from detailed 3D FE limit analysis using elastic-perfectly-plastic material behaviour do not exhibit the asymptotic behaviour predicted by BS 7910 as the flaw transitions from deep crack to through-thickness crack. Furthermore, K_r predicted by BS 7910 is shown to be an over-estimation for the typical dimensions of offshore monopiles. The findings suggest that a structure with a deep flaw may be identified as unacceptable based on BS 7910 when it may still possess a non-trivial amount of structural residual life. This is a concern for monopiles where crack growth as a large flaw forms a significant part of the total life.     

舰载雷达稳定平台基座优化设计

本文对某舰载雷达稳定平台基座在船摇、风载和振动载荷作用下的受力情况进行分析和计算。运用有限元技术对原基座的载荷分布进行分析,同时对基座进行结构优化设计。通过对优化后基座的有限元分析计算表明其满足减重要求和船摇、风载和振动条件下的强度设计要求。     

基于UMAT的冰—结构相互作用数值仿真

基于ABAQUS 用户自定义子程序UMAT,采用已有的冰的弹性失效准则,针对冰与结构的相互作用进行数值模拟。首先, 通过简单算例验证本文开发的UMAT的正确性;然后, 采用开发的UMAT建立单个冰单元受刚性板挤压下的力学模型,得到力—位移曲线;最后, 通过建立圆柱与冰相互作用的仿真分析模型,探讨冰板厚度对结构反力的影响。研究结果表明,采用用户自定义程序UMAT使得模拟更为复杂的冰力学特性成为可能,可为以后开展大规模的冰—结构相互作用研究奠定基础。