地铁信号与站台门接口故障分析

分析地铁信号与站台门系统接口故障对运营造成的影响以及地铁新线开通初期设备故障率较高的现状,对站台门状态未反馈及站台门不联动接口故障进行分析,阐述其发生的原因、处理办法。前瞻性地提出地铁新线建设时信号与站台门接口故障隐患防范措施和思路,减少设备故障率,最大限度降低信号与站台门接口故障对运营带来的影响,为新线正常运营奠定基础。     

Fault classification method for the driving safety of electrified vehicles

A fault classification method is proposed which has been applied to an electric vehicle. Potential faults in the different subsystems that can affect the vehicle directional stability were collected in a failure mode and effect analysis. Similar driveline faults were grouped together if they resembled each other with respect to their influence on the vehicle dynamic behaviour. The faults were physically modelled in a simulation environment before they were induced in a detailed vehicle model under normal driving conditions. A special focus was placed on faults in the driveline of electric vehicles employing in-wheel motors of the permanent magnet type. Several failures caused by mechanical and other faults were analysed as well. The fault classification method consists of a controllability ranking developed according to the functional safety standard ISO 26262. The controllability of a fault was determined with three parameters covering the influence of the longitudinal, lateral and yaw motion of the vehicle. The simulation results were analysed and the faults were classified according to their controllability using the proposed method. It was shown that the controllability decreased specifically with increasing lateral acceleration and increasing speed. The results for the electric driveline faults show that this trend cannot be generalised for all the faults, as the controllability deteriorated for some faults during manoeuvres with low lateral acceleration and low speed. The proposed method is generic and can be applied to various other types of road vehicles and faults.     

运梁河特大桥转体梁不平衡重称重试验分析

哈大客专运粮河特大桥跨既有线连续梁采用平转法施工,为确保转体顺利进行,转体前进行了T构不平衡重试验分析,文中介绍了一种转体构件不平衡重的测试方法和应用过程。结果表明,方法有效可行,可供同类工程借鉴。     

城市轨道交通快线轮轨侧磨成因及防治

对目前轨道交通快线开通运营后轮轨侧磨情况进行深入调研,对轮轨侧磨的特点、成因进行分析,通过动力仿真计算,对比分析100 km/h轨道交通快线车辆与传统80km/h地铁车辆轮轨侧磨程度的差异,最后针对轨道交通快线的轮轨侧磨问题提出防治措施.     

基于Ansys的矩形加筋平盖封头强度评定

将有限元方法与分析设计相结合,利用有限元分析软件Ansys对一种矩形加筋平盖封头进行强度评定。本文首先介绍瓶盖封头结构的改进。然后建立有限元模型,并进行应力求解。结果表明,此加筋平盖封头满足强度要求,与普通平盖封头相比,减小了平盖的厚度,降低了结构总重量,对平盖封头的结构改进设计具有一定指导作用。     

Dynamic simulation of train–truck collision at level crossings

Trains crashing onto heavy road vehicles stuck across rail tracks are more likely occurrences at level crossings due to ongoing increase in the registration of heavy vehicles and these long heavy vehicles getting caught in traffic after partly crossing the boom gate; these incidents lead to significant financial losses and societal costs. This paper presents an investigation of the dynamic responses of trains under frontal collision on road trucks obliquely stuck on rail tracks at level crossings. This study builds a nonlinear three-dimensional multi-body dynamic model of a passenger train colliding with an obliquely stuck road truck on a ballasted track. The model is first benchmarked against several train dynamics packages and its predictions of the dynamic response and derailment potential are shown rational. A geometry-based derailment assessment criterion is applied to evaluate the derailment behaviour of the frontal obliquely impacted trains under different conditions. Sensitivities of several key influencing parameters, such as the train impact speed, the truck mass, the friction at truck tyres, the train–truck impact angle, the contact friction at the collision zone, the wheel/rail friction and the train suspension are reported.     

基于系统集成理论的城市道路景观设计

在我国城市道路景观实践过程中,由于建造时序的不同,城市道路的“景观破碎、缺乏集成”和“豪华奢侈、脱离实际”,不利于城市系统的和谐发展。鉴于此,本文在深入分析城市道路景观建设目标的基础上,独辟蹊径从系统范畴的角度探讨了一种“集成”的道路景观设计理念,为城市道路景观的建设提供了一个新的思路。     

沥青桥面铺装早期破坏原因分析

从设计、施工、外部原因等方面分析沥青桥面铺装早期破坏原因及其相应防治措施。     

地震作用下钢筋混凝土桥墩抗倒塌性能研究

为研究混凝土桥墩的结构抗震性能,进行了单墩多自由度体系非线性静力推倒分析、非线性动力分析、增量动力分析。分别采用纤维模型中分布塑性铰和集中塑性铰两种建模方法,建立单墩有限元模型,利用Open Sees软件中的Hysteretic滞回模型考虑各种累积损伤的影响。     

低温独立液舱曲面外板加工减薄量评估

基于耐低温合金材料的非线性特性,以某液化气船的低温独立液舱曲面外板加工成形过程为研究对象,研究其塑形变形过程及机理。利用ABAQUS作为计算分析工具,建立了板材原料及上、下加工模具的分析模型,给定冲压成形的时间和初始速度,并设定时间步长,考察每个时间步长的计算结果,分析了其加工过程中的弹塑性变形过程,评估了低温合金材料在加工过程中的板厚变化情况,并与实际加工测量值进行对比,验证了模型和计算分析过程的准确性。为各类低温独立液舱的设计和材料尺寸选用提供了技术支持和指导。