轨道安全监测中传感器优化配置研究

为了研究轨道结构安全监测中传感器的合理配置方法,确保城市轨道交通安全运营,通过建立桥上交叉渡线道岔模型和钢轨应变传递误差最小的目标函数,提出传感器测点选择依据和监测方案评价标准,保证监测方案的经济性、合理性。结论表明:模型数据曲线可以指导监测系统的测点位置选择;随着传感器测点数量增加,监测误差逐渐减小,但在误差比率的"拐点"后增加单位个数传感器带来的收益降低;通过建立误差最小准则的目标函数,结合误差指标可以评价和优化传感器布设方案;钢轨位移、附加力等指标的监测方案也可以通过本文方法确定。     

新建隧道下穿多座隧道施工技术

以渝黔引入贵阳枢纽铁路龙宝冲隧道下穿6座已建及在建隧道工程为例,结合现场,详细分析、介绍了下穿隧道施工方案、原则、施工方法;提出了新建铁路隧道近距离下穿隧道交叉点附近施工爆破控制、防护方案,以及新建、既有隧道的监控量测、超前地质预报、安全性评估与评价等施工技术;解决了下穿隧道施工中既保证新建隧道施工安全,又保证既有隧道不受影响的问题。     

钢檩条设计中的若干问题

轻型屋面钢檩条的竖向荷载、整体稳定性计算以及檩条与屋面梁、屋架的连接构造是设计的重要环节,本文结合规范和国家标准设计图的编制提出若干问题,供参考.     

立交隧道相互作用三维数值模拟与实测对比研究

以温福铁路琯头岭隧道下穿同三高速公路隧道为例,研究新建下穿隧道与既有隧道工程之间相互影响的问题。采用ANSYS有限元软件,模拟上覆公路隧道和下穿铁路隧道的位移和应力变化情况,并与现场监控量测结果对比,得到以下结果:下穿隧道拱顶沉降量较小,水平收敛值较大,下穿隧道立交段拱腰和边墙是需要重点支护的对象;上覆隧道在立交段下沉值变大,变化幅度为仰拱边墙拱腰拱顶,隧道中部和下部水平收敛值变化较大;受下穿隧道开挖影响,立交隧道上覆地层受力产生不均匀变化,造成扭矩存在,地面水平位移整体呈现"8"字形,立交隧道的建设对地层产生了较大的转动扰动。     

小直径盾构施工中管片纵向应力监测研究

为了探索小直径盾构法隧道在施工过程中管片纵向应力的变化规律,对北京槐房再生水厂污水隧道管片纵向应力进行了现场监测:将第976环、第1 054环管片分别设为第1和第2监测断面,2监测断面各预埋5个纵向应力计,各监测断面从本监测断面管片安装后即开始监测,当盾构掘进至第1 129环时停止监测。研究表明:1)在管片离开盾尾50环后,其纵向应力波动值小于管片拼装期间应力值的5%。2)在盾构掘进期间,管片距离盾构越远,其纵向压应力值越小。3)在管片拼装期间,管片距离盾构越远,其纵向压应力经历了先增大后减小的过程。4)管片距离盾构108环后,该管片纵向压应力趋近于0.2~0.3 MPa。5)随着盾构推进,管片纵向应力经历了4个阶段的变化过程,即周期性剧烈波动阶段—动态稳定阶段—逐渐衰减阶段—趋于稳定阶段。     

薄基岩顶板隧道爆破施工围岩稳定性分析

为更有效地进行薄基岩顶板条件下隧道施工安全控制,以某高速公路隧道为工程背景,运用数值模拟的方法,分别研究不同顶板厚度下隧道爆破施工引起的围岩振速分布特征及其对围岩的损伤情况,并进行围岩稳定性分析。结果表明:1)当顶板厚度在5 m及以上时,围岩是稳定的;2)当顶板厚度为3 m时,最危险横断面上基岩顶板内开始产生严重的拉伸裂缝及一些径向裂缝,将形成超挖;3)当顶板厚度≤2 m时,径向裂缝贯穿顶板岩体,围岩稳定性较差,在掌子面后1 m内可能发生塌落、掉块等事故。     

Magneto-rheological suspensions for improving ground vehicle’s ride comfort,stability, and handling

ABSTRACT

A state-of-the-art discussion on the applications of magneto-rheological (MR) suspensions for improving ride comfort, handling, and stability in ground vehicles is discussed for both road and rail applications. A historical perspective on the discovery and engineering development of MR fluids is presented, followed by some of the common methods for modelling their non-Newtonian behaviour. The common modes of the MR fluids are discussed, along with the application of the fluid in valve mode for ground vehicles’ dampers (or shock absorbers). The applications span across nearly all road vehicles, including automobiles, trains, semi-trucks, motorcycles, and even bicycles. For each type of vehicle, the results of some of the past studies is presented briefly, with reference to the originating study. It is discussed that Past experimental and modelling studies have indicated that MR suspensions provide clear advantages for ground vehicles that far surpasses the performance of passive suspension. For rail vehicles, the primary advantage is in terms of increasing the speed at which the onset of hunting occurs, whereas for road vehicles – mainly automobiles – the performance improvements are in terms of a better balance between vehicle ride, handling, and stability. To further elaborate on this point, a single-suspension model is used to develop an index-based approach for studying the compromise that is offered by vehicle suspensions, using the H₂ optimisation approach. Evaluating three indices based on the sprung-mass acceleration, suspension rattlespace, and tyre deflection, it is clearly demonstrated that MR suspensions significantly improve road vehicle’s ride comfort, stability, and handling in comparison with passive suspensions. For rail vehicles, the simulation results indicate that using MR suspensions with an on-off switching control can increase the speed at which the on-set of hunting occurs by as much as 50% to more than 300%.     

A study on the stability of a motorcycle wheel–swingarm suspension with chain transmission

The present study describes a possible driving mechanism for a self-excited oscillation observed in motorcycle dynamics, often referred to as chatter. This phenomenon, affecting the performance of road racing motorcycles, has been simulated in straight running braking manoeuvres with multibody motorcycle models. It involves rear suspension bounce and driveline oscillation in the frequency range between 17 and 22?Hz. A simplified model of a motorcycle rear suspension with chain transmission is proposed and its stability in equilibrium configurations is studied via eigenvalue analysis. The sensitivity with respect to all its governing parameters is analysed by means of stability maps and the self-excitation mechanism is explained with the aid of energy balance analysis and phase diagrams. It is found that the key role for the instability onset is played by the gradient of the nonlinear characteristic slip function of the tyre.     

Simulation and analysis of vehicle stability based on ADAMS/CAR differential brake

To improve the braking safety of automobiles, the author studied the effect of differential brake on the stabilities. To analyze the mechanical characteristics of differential brake, automotive subsystem models were built by applying ADAMS/CAR, and automotive mechanics simulation model was built by setting the main subsystems such as body, engine and brake. The simulation model studied the distribution mode of three kinds of differential brake, and beeline braking stability and turning braking stability were simulated. It shows that differential brake can amend turning shortage of automobile brake and improve its braking stability, but the effect of automobile mass on its braking stability is great. So the distribution mode of braking force and the effect of mass change should be considered while differential brake is applied.     

沥青玛蹄脂混合料的高温性能影响因素分析

沥青玛蹄脂混合料作为良好的钢桥面铺装层材料,其高温性能一直是关注的焦点,本文基于室内车辙试验研究了其高温性能影响因素,重点分析了荷载和温度、拌合时间及加铺SMA对沥青玛蹄脂混合料的高温性能指标动稳定度的影响规律,为今后玛蹄脂混合料的路用实践提供了借鉴.