120阀试验过程的计算机仿真——紧急阀模型及仿真结果

建立了１２０紧急阀和试验台计算仿真模型，仿真了１２０紧急阀在试验台上的试验过程，结果表明：该模型能很好的仿真１２０阀在试验台上紧急阀试验，利用模型预测了试验台管径变化对紧急阀试验性能的影响，计算发现：管径主要影响紧急灵敏度和列车管排气时间。压力表安装位置分析表明：对于气体流速较快工况，测量结果与压力表的位置相关性较大，需要慎性确定压力表位置。该工作为试验台设计、试验规范制定和１２０紧急阀性能改进提     

橡胶沥青性能影响因素的试验研究

为了正确控制橡胶沥青工艺,采用不同胶粉种类、胶粉细度、拌和温度、基质沥青类型等制备橡胶沥青,进行针入度、软化点、弹性恢复以及SHRP等试验,分别测试橡胶沥青的高温性能、低温性能、抗老化性能等,研究各因素对橡胶沥青性能的影响,得出20目橡胶粉掺量以16%~18%较为合适的结果。     

Dynamic model for ride comfort evaluations of the rubber-tired light rail vehicle

The dynamic model was developed to evaluate vibration accelerations and ride comforts during the running of the Korean-standardised rubber-tired light rail vehicle. Ride comfort indexes were analysed and tested in accordance with UIC 513R by using the dynamic model and the actual vehicle in the test track. Based on the comparisons between analysis results and test results, the validity of the developed dynamic model was evaluated. It was verified whether or not the developed Korean-standardised rubber-tired light rail vehicle met the specified target specification on ride comfort. In addition, the influence of the wearing of guide wheels on ride comfort was estimated.     

Indirect method for wheel–rail force measurement and derailment evaluation

Wheel set flange derailment criteria for railway vehicles are derived and the influence of wheel–rail contact parameters is studied. An indirect method for wheel–rail force measurement based on these derailment evaluation criteria is proposed. Laboratory tests for the calibration of strain–force devices on the bearing box are carried out to determine the relationship between the applied force and the measured strain. The simulation package, SIMPACK, is used to develop a passenger car model to generate wheel–rail forces and vibration signals. Different cases are considered in this model to provide an accurate validation of the identified wheel–rail forces. A feasibility test is conducted in the Beijing Loop test line using a passenger car equipped with a set of strain gauges on the wheel set. The comparison of the force time history applied to the instrumented wheel set and that obtained using the indirect method is presented.     

某出口米轨动车组(Tc车)车体设计及试验对比研究

介绍了使用大型通用计算机辅助工程软件ANSYS和有限元方法,对某出口米轨动车组(Tc车)进行了分析计算的过程,并通过实际物理样机试验数据与计算数据的比对,分析车身强度的可靠性。     

Non-fragile multi-objective static output feedback control of vehicle active suspension with time-delay

This paper presents an approach to design a delay-dependent non-fragile H_∞/L₂–L_∞ static output feedback (SOF) controller for active suspension with input time-delay. The control problem of quarter-car active suspension with actuator time-delay is formulated to a H_∞/L₂–L_∞ control problem. By employing a delay-dependent Lyapunov function, new existence conditions of delay-dependent non-fragile SOF H_∞ controller and L₂–L_∞ controller are derived, respectively, in terms of the feasibility of bilinear matrix inequalities (BMIs). Then, a procedure based on linear matrix inequality optimisation and a hybrid algorithm of the particle swarm optimisation and differential evolution is used to solve an optimisation problem with BMI constraints. Design and simulation results of non-fragile H_∞/L₂–L_∞ controller for active suspension show that the designed controller not only can achieve the optimal performance and stability of the closed-loop system in spite of the existence of the actuator time-delay, but also has significantly improved the non-fragility characteristics over controller perturbations.     

砂、石材料坚固性试验的研究

通过进行砂、石材料坚固性直接冻融和硫酸钠法的对比试验,总结出对工程耐久性的影响和两种方法不可替代的关系。     

公路工程施工要点及其控制

简述了公路面层及基层施工控制要点,并介绍了施工过程中需要的各种检测,以便及时反馈,做好施工控制工作,对保证沥青混凝土路面的施工质量,具有一定的指导意义。     

新建结构与运营地铁车站接驳关键技术

以深圳地铁新建3号线老街站换乘综合体与运营地铁车站接驳工程为实例,对运营车站临时加固防护、分部切割既有结构、新旧结构接驳等关键技术展开论述。提出运用金刚石绳锯与金刚石水钻相结合的一种静力切割工艺,很好地解决了该工程作业环境复杂、技术要求高、风险大等难题,安全、高效地完成了新建结构与运营地铁车站接驳工程。     

基于LabVIEW和PXI的电力机车电气综合性能测试系统

介绍了电力机车电气综合性能测试平台的基本组成,从硬件平台、软件设计等方面详细分析了基于LabVIEW和PXI的电力机车电气综合性能测试系统的开发应用。