Geometric-based tyre vertical force estimation and stiffness parameterisation for automotive and unmanned vehicle applications

Advanced empirical, and physical-based tyre models have proven to be accurate for simulating tyre dynamics; however, these tyre models typically require expensive and intensive tyre parameterisation. Recent research into wheeled unmanned ground vehicles requiring vertical force analysis has shown good results using a simple linear spring model for the tyre which demonstrate the continued use for simple tyre models; however, parameterisation of the tyre still remains a challenge when load test equipment is not available. This paper presents a cost-effective tyre vertical stiffness parameterisation procedure using only measured tyre geometry and air pressure for applications where high-fidelity tyre models are unnecessary. Vertical forces calculated through an air volume optimisation approach are used to estimate tyre vertical stiffness. Nine tyres from the literature are compared to evaluate the performance of the vertical force estimation and stiffness parameterisation algorithms. Experimental results on a pair of ATV tyres are also presented.     

浅谈汽车轮胎的使用负荷

轮胎的使用负荷是影响轮胎使用寿命的主要因素之一 ,通过对轮胎使用负荷的测算 ,为合理地选用轮胎的规格和尺寸提供依据     

A planar quasi-static constraint mode tyre model

The fast-paced, iterative, vehicle design environment demands efficiency when simulating suspension loads. Towards that end, a computationally efficient, linear, planar, quasi-static tyre model is developed in this work that accurately predicts a tyre's lower frequency, reasonably large amplitude, nonlinear stiffness relationship. The axisymmetric, circumferentially isotropic, stiffness equation is discretised into segments, then parameterised by a single stiffness parameter and two shape parameters. The tyre's deformed shape is independent of the overall tyre stiffness and the forces acting on the tyre. Constraint modes capture enveloping and bridging properties and a recursive method yields the set of active constraints at the tyre–road interface. The nonlinear stiffness of a tyre is captured by enforcing unidirectional geometric boundary conditions. The model parameters are identified semi-empirically; simulated cleat test loads match experiments within 7% including nonlinear stiffness when simulating a flat plate test and a discontinuous stiffness when simulating a cleat test.     

An optimal pole-matching observer design for estimating tyre–road friction force

In this paper, considering the dynamical model of tyre–road contacts, we design a nonlinear observer for the on-line estimation of tyre–road friction force using the average lumped LuGre model without any simplification. The design is the extension of a previously offered observer to allow a muchmore realistic estimation by considering the effect of the rolling resistance and a term related to the relative velocity in the observer. Our aim is not to introduce a new friction model, but to present a more accurate nonlinear observer for the assumed model. We derive linear matrix equality conditions to obtain an observer gain with minimum pole mismatch for the desired observer error dynamic system. We prove the convergence of the observer for the non-simplified model. Finally, we compare the performance of the proposed observer with that of the previously mentioned nonlinear observer, which shows significant improvement in the accuracy of estimation.     

A reduced-order nonlinear sliding mode observer for vehicle slip angle and tyre forces

In this paper, a reduced-order sliding mode observer (RO-SMO) is developed for vehicle state estimation. Several improvements are achieved in this paper. First, the reference model accuracy is improved by considering vehicle load transfers and using a precise nonlinear tyre model ‘UniTire’. Second, without the reference model accuracy degraded, the computing burden of the state observer is decreased by a reduced-order approach. Third, nonlinear system damping is integrated into the SMO to speed convergence and reduce chattering. The proposed RO-SMO is evaluated through simulation and experiments based on an in-wheel motor electric vehicle. The results show that the proposed observer accurately predicts the vehicle states.     

A lateral driver model for vehicle–driver closed-loop simulation at the limits of handling

This paper presents a lateral driver model for vehicle–driver closed-loop simulation at the limits of handling. An appropriate driver model can be used to evaluate the performance of vehicle chassis control systems via computer simulations before vehicle tests which incurs expenses especially at the limits of handling. The driver model consists of two parts. The first part is an upper-level controller employing force-based approach to reduce the number of unknown vehicle parameters. The feedforward part of the upper controller has been designed by using the centre of percussion. The feedback part aims to minimise ‘tangential error’, defined as the sum of body slip angle and yaw error, to match vehicle direction and road heading angle. The part is designed to regenerate an appropriate skid motion similar to that of a professional driver at the limits. The second part is a lower-level controller which converts the desired front lateral force to steering wheel angle. The lower-level controller also consists of feedforward and feedback parts. A two-degree-of-freedom bicycle model-based feedforward part provides nominal steering wheel angle, and the feedback part aims to eliminate unmodelled error. The performance of the lateral driver model has been investigated via computer simulations. It has been shown that the steering behaviours of the proposed driver model are quite close to those of a professional driver at the limits. Compared with the previously developed lateral driver models, the proposed lateral driver model shows good tracking performance at the limits of handling.     

Time-optimal control of the race car: influence of a thermodynamic tyre model

The robustness of an existing numerical method for the time-optimal control of the race car is demonstrated through its application to a model of a Formula 1 car equipped with a simplified thermodynamic tyre model. The tyre model includes a temperature- and frequency-dependent model of road/tyre friction. A lumped parameter approach is used to model the thermodynamics of the various parts of the tyre such as the tread, carcass and inflation gas. The influence of tyre, track surface and ambient temperatures on time-optimal manoeuvring is presented.     

Tuning and objective performance evaluation of a driving simulator to investigate tyre behaviour in on-centre handling manoeuvres

Driving simulation aims at reproducing, within a safe and controlled environment, sensorial stimuli as close to those perceived during the actual drive as possible, in order to induce driving behaviour similar to the real one. This paper illustrates an activity carried out on the driving simulator Virtual Environment for Road Safety, bound for system performance optimisation while dealing with subjective and objective tyres evaluation in the field of on-centre manoeuvres. Such activity can be divided into two main steps. The first one, described herewith, has been focusing on platform motion algorithms tuning and has led to driving simulator objective validation within the on-centre range. Device capability of reproducing dynamics, worked out by the vehicle model, has been thoroughly examined. Simulator sensitivity to a few tyre parameters influencing vehicle lateral dynamics has been analysed too. The second step – calling for the support of experienced drivers – will pursue subjective validation.