基于圆形断面的隧道温度场有限差分计算模型

除了少数圆形隧道外,大部分山岭交通隧道断面采用马蹄形或端墙式等形状。在隧道温度场的预测中,圆形断面模型能否代替马蹄形等实际隧道模型,其适应性值得研究。应用基于空气－衬砌－围岩的对流－导热耦合作用控制方程的有限差分方法,建立圆形断面模型对东北寒区马蹄形隧道温度场进行计算,并与现场实测温度场进行对比。结果表明： 1) 圆形断面隧道模型有限差分计算方法克服了通用有限元软件建模复杂、对硬件要求高的弊端,考虑了隧道内风流速度和入口风流温度的影响,在隧道温度场的预测计算中能够满足工程使用要求。2）隧道内风流速度和入口风流温度对隧道温度场影响较大。本文算例中,入口风流温度每升高10 ℃,二次衬砌表面温度升高约7.2 ℃,增幅均匀;从1～5 m/s,洞内风流速度每增大1 m/s,二次衬砌表面温度降低的幅度为6.6、2.7、1.5、0.9 ℃,降幅越来越小。     

防水粘结材料抗剪性能对比研究

选用胶粉改性沥青和SBS改性乳化沥青作为桥面铺装防水粘结材料,对桥面铺装结构进行不同温度下的剪切强度测试,并在冻融循环及浸水2种环境因素下,对2种防水粘结材料抗剪强度的变化规律进行试验研究。试验结果表明:抗剪强度随温度升高而降低;在冻融及浸水作用下抗剪强度也会降低,但胶粉改性沥青稳定性优于SBS改性乳化沥青,是一种更优的防水粘结材料。该试验结果可为类似工程施工提供参考。     

倒装型沥青路面温度场时空分布规律分析

倒装型基层是福建省常用的沥青路面结构型式,其沥青层厚度达26cm。而沥青材料性质对温度敏感,进行温度场分析很有必要。通过有限元仿真分析,对福建省夏季高温时典型日照下倒装沥青路面结构内的温度场进行计算,得到内部各层温度的时空分布,并经过经验公式和相关资料的实际监测验证。结果表明,有限元分析可以作为沥青路面结构设计和沥青材料选择时计算路面温度的快捷可靠的方法。     

不同温拌剂对沥青路用性能的影响

为研究不同类型温拌剂对于沥青性能的影响,选择常用降黏型温拌剂Sasobit和发泡型温拌剂Asphamin分别加入到基质沥青和SBS改性沥青中,通过针入度、软化点、延度及黏度试验,研究对比这两类温拌剂对沥青感温性能、高低温性能及黏滞性的影响。由等黏温度定理,推算出部分温拌沥青混合料的施工温度,并以此对比分析其降温效果。结果表明:两类温拌剂均能显著提高沥青高温性能,掺入4%Sasobit和4%Aspha-min能使沥青软化点分别增长48%和31%,均可有效降低沥青的高温黏度和压实温度(降温范围在18～24℃之间)。同时,也能提升沥青的低温黏度(95℃下分别提升278%和14.7%),提高沥青路面抗流动变形的能力。但两种温拌剂对沥青低温性能呈不利影响,且这种不利影响与掺量呈正相关,因此应合理控制温拌剂掺量。     

Size effect on residual stress in low transformation temperature welded joints

It has been reported that low transformation temperature (LTT) weld metals are beneficial to generation of compressive residual stress around weld zone. In this study, the relationship among residual stress, size effect of LTT welded joints with different plate width and thickness as well as martensite start (Ms) temperatures was investigated by experimental and finite-element analysis. It was found that heat dissipation and thermal expansion coefficient of LTT weld metal had a significant impact on residual stress. Welded joint with a small plate width led to greater compressive residual stresses in the LTT weld, which was due to the lower heat dissipation and smaller thermal expansion coefficient of the LTT weld metal in due course of cooling process. Additionally, the finite-element analysis revealed that increasing plate width mainly affected the longitudinal residual stress, while increasing the plate thickness influenced all the residual stress components in the LTT weld. Furthermore, the LTT weld with a lower Ms temperature of 191 °C resulted in greater compressive residual stresses, and was less sensitive to the LTT joint size, as against the Ms temperature of 398 °C.     

气液-压溃组合式缓冲装置冲击吸能特性实验研究

动车组用中间车钩缓冲吸能装置主要由气液缓冲器和压溃管组成,为研究其工作场景中动态吸能特性,采用两辆台车与中间车钩连挂,撞向刚性墙进行冲击实验,台车冲击速度分别为7.19、18.7和25.7 km/h 3种工况。冲击作用下,气液缓冲器阻抗力具有明显的动态特性,最大压缩行程的阻抗力随冲击速度提升而增高,可达1500 kN,远高于其静压实验最大阻抗力800 kN;而压溃管动态阻抗力与静压结果基本一致为1500 kN;冲击速度为18.7和25.7 km/h,气液缓冲器压缩行程达到30 mm时,阻抗力达1200 kN,压溃管被触发压溃,气液缓冲器与压溃管同时进入压缩状态,一起压缩变形。     

Investigations on the ship-ice impact: Part 1. Experimental methodologies

In the structural design of the Polar Class ships, glancing impact with ice has been considered as the governing load scenario for dimensioning the bow structure. At present, non-linear transient dynamic analysis has been reckoned as a fundamental requirement in the assessment of the structural strength of ships with higher ice classes. Under such requirement, understanding of the dynamic characteristics of the ship-ice impact load appears significant importance. The present study aims to investigate the spatial and temporal variations of the impact loads by simulating the glancing impact events between a polar research vessel and giant ice floes in ice tank. The ship-ice impact loads were recorded by a grid-based tactile sensor attached on the bow area of the model ship. To achieve a reasonable simulation on the design scenario described by the IACS Unified Requirements for Polar Class Ships (UR I), a series of methodological calibration tests were preliminarily carried out to determine the key parameters that should be carefully monitored and controlled, accompanying with thorough discussions on the ship-ice impact process. This paper provides detailed information on the preliminary methodological calibrations and the tactile data processing techniques, including the identification of the ship-ice contact area, the depiction of the ice loading trail and the outline of the spatial distributions of local ice pressures. A companion paper provides detailed analyses and discussions regarding the spatial and temporal variation of the ice impact loads from the formal tests based on the proposed testing procedures obtained by the methodological calibrations.     

水中悬浮隧道受撞击作用的数值分析

针对水中悬浮隧道在偶然状况下受到的潜艇撞击问题,文章采用流固耦合方法,建立了撞击作用下浮筒式悬浮隧道的有限元动态模型,分别撞击跨中、隧道四分之一跨、浮筒,分析隧道变形、撞击力、连接钢管拉杆力、隧道端部约束力、隧道动能情况。结果表明:撞击作用下,隧道整体变形明显,结构内力大。不同撞击位置处,悬浮隧道在水下的结构变形和受力行为区别明显。对此,有必要考虑撞击位置进行悬浮隧道的抗撞击设计。     

Estimating fuel burn impacts of taxi-out delay with implications for gate-hold benefits

The aviation community is actively investigating initiatives to reduce aircraft fuel consumption from surface operations, as surface management strategies may face fewer implementation barriers compared with en route strategies. One fuel-saving initiative for the air transportation system is the possibility of holding aircraft at the gate, or the spot, until the point at which they can taxi unimpeded to the departure runway. The extent to which gate holding strategies have financial and environmental benefits hinges on the quantity of fuel that is consumed during surface operations. A pilot of an aircraft may execute the taxi procedure on a single engine or utilize different engine thrust rates during taxi because of a delay. In the following study, we use airline fuel consumption data to estimate aircraft taxi fuel consumption rates during the “unimpeded” and “delayed” portions of taxi time. We find that the fuel consumption attributed to a minute of taxi-out delay is less than that attributed to minute of unimpeded taxi time; for some aircraft types, the fuel consumption rate for a minute of taxi delay is half of that for unimpeded taxi. It is therefore not appropriate, even for rough calculations, to apply nominal taxi fuel consumption rates to convert delayed taxi-out time into fuel burn. On average we find that eliminating taxi delay would reduce overall flight fuel consumption by about 1%. When we consider the savings on an airport-by-airport basis, we find that for some airports the potential reduction from reducing taxi delay is as much as 2%.     

混凝土箱梁水化热温度试验研究

研究目的:温度应力已被认为是混凝土箱梁开裂的主要原因之一。为了掌握水化热温度沿箱梁截面的分布规律,并根据混凝土施工工艺状况,估算温差应力,特对混凝土箱梁进行了水化热温度试验,为箱梁设计与施工提供有益的参考。研究方法:水化热温度测试选取了梁体的跨中及端部截面,按照能够充分反映箱梁水化热变化情况的原则,分别在顶板、底板、腹板布置了内埋式温度传感器,从混凝土入模开始,量测水化热温度的变化情况。研究结果:根据温度测试结果,可以绘制出混凝土水化热温度随观测时间变化的曲线。通过对秦沈客运专线箱梁温度测试结果的总结分析,重点阐述了箱梁混凝土早期水化热温度发展的一般规律,其中包括水化热温度时程曲线的一般形式、温升基本规律、温降基本规律、混凝土的温度梯度、入模温度与温度峰值的关系等,并提出了防止温差过大而引起混凝土开裂的工程措施。