双月池对某援潜救生船运动性能及波面升高的影响

介绍某援潜救生船配设双月池的船型特点,规划双月池和不带月池2种方案来评估双月池开口对援潜救生船船体运动性能的影响。采用三维势流理论对2个方案的运动性能进行计算,得到船体运动响应函数,对船舶运动性能进行短期预报,研究总结双月池效应对援潜救生船运动的影响规律。对比双月池内水面和舷外波面升高的情况,比较两个位置处波面升高的差异性,总结双月池波面升高对潜水钟收放的影响。     

Effect of Explosion in a Gas Pipeline Compartment of a Utility Tunnel on Neighboring Metro Tunnels北大核心CSCD

In this paper the numerical simulation analysis of the effect of explosion in the gas pipeline compartment of a utility tunnel on neighboring metro tunnels was conducted using the software AUTODYN. The results show that the TNT equivalent in a fireproof partition with length of 200 m is 41.6 kg when the gas concentration in the gas pipeline compartment reaches 10%; the blast wave has much effect on the crown and arch waist of the round metro tunnel and it’s necessary to take some protective measures in both areas; when the surrounding soil is sand, the utili- ty tunnel is above the round metro tunnel and their alignments are in the same direction, the greater the vertical spacing between the utility tunnel and the metro tunnel, the smaller the effect of the blast wave on the metro tunnel; when the vertical spacing is 7.2 m, the maximum dynamic tensile stress is 1.86 MPa (including the static stress value of 1 MPa in the tunnel segment) and it is slightly smaller than the designed tensile strength of metro tunnel (about 1.89 MPa). The maximum vibration velocity and the maximum displacement meet the structural stability require- ments, so it is suggested the vertical spacing between the utility tunnel and metro tunnel shall not be less than 7.2 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

45000t集装箱滚装船水密门精度控制

为更好地控制集装箱滚装船门框结构的安装精度,以45000t集装箱滚装船中只包含水密门结构的分段为例进行水密门精度控制研究。通过研究该分段的建造方式,改进分段的建造工艺,合理安排门框结构在分段建造过程中的安装顺序,进而缩减结构变形;同时,利用精度测量仪器进行跟踪测量,保证始终把精度控制在有效范围内。对焊接过程中采用的焊接方法进行研究,改进焊接工艺,采取逐步退焊法控制焊接热量,进而减少焊接变形。通过对分段水密门门框结构的安装工艺及焊接工艺进行研究,将理论与实践相结合,总结出一套行之有效的建造工艺,确保分段门框结构安装精度得到有效控制,保证水密门的性能,为该系列船后续的分段建造提供参考。     

Preliminary investigation of PM1, PM2.5, PM10 and its metal elemental composition in tunnels at a subway station in Shanghai,China

In this study, real-time monitoring campaigns were conducted in two tunnels (Line A and Line B) at a subway station in Shanghai, including temperature, relative humidity, PM₁, PM_2.5 and PM₁₀, in order to understand the climate and PM characteristics in the transportation microenvironment. In addition, collected floor dust particles in the tunnel were analyzed by ICP for their metal elemental composition. Strong correlations occurred between all PM levels and meteorological parameters in the tunnel of Line A (with platform screen doors), in comparison with the weak correlations between such parameters in the tunnel of Line B (without platform screen doors). PM_2.5 and PM₁₀ between peak hours and off-peak hours for both lines presented significant differences (p < 0.05), respectively. Nevertheless, PM₁ showed a different pattern, with p > 0.05 for Line A and p < 0.05 for Line B, respectively. In addition, statistical results concluded that PM had an evident weekly variation for both lines. Friday was the highest day of all particulate matters in monitoring periods for both lines. Ratios of PM₁/PM₁₀ and PM_2.5/PM₁₀ were high when trains were out of service and low when trains were in service. Relative abundance of metal elements detected from floor dust particles proved that floor dust particles in tunnels might be a major source of airborne PM in the subway microenvironments, with Fe as the most abundant metal element, followed by Ca, Al, Mg, Mn, Zn, Cu, Cr, Ni, Pb and Hg.     

地铁车站防火与维修通道设计冲突及解决

为了解决在前期施工过程中提前发现的地铁站中电话接线房、饮水泵房和防水泵房的防火设计与后期对相应设施的维修所存在的设计冲突,通过进行防火分区的研究以及结构受力计算和分析,在设计中采用了在电话接线房和防火房顶部增设顶板的方式来满足防火要求,此外还在饮水泵房设计中不设顶板从而满足后期对相应设施进行维修的要求。     

电子差速系统轮胎附着特性模拟仿真研究

电子差速系统相对于传统的机械式差速器可以实现转矩的精准分配,根据轮胎的纵向运动特性以及侧向运动特性,结合轮胎滑移率让内外侧车轮在过弯时拥有足够的附着力,减小整车的横摆角速度,提高过弯稳定性。采用后轮双电机的驱动方案,驱动电机采用直接转矩控制的方法,由整车控制器将指定的计算转矩信号发送给电机控制器完成动力分配,所需转矩根据驾驶员的加速踏板及方向盘转角,运用阿克曼转向模型计算得到。     

三角闸门门缝输水运行工况研究

门缝输水是三角闸门的一种重要特性。基于三角闸门门缝输水,低水头船闸可以不设置阀门以降低工程建设成本,但具体适用工况尚难把握。依托未设置阀门的大柳巷船闸,采用理论计算与现场实测相结合的方法,分析了门缝输水时水力及启闭力。研究表明:口门越大三角闸门能承受门缝输水的水头越小;目前门缝输水有关计算公式尚需结合三角闸门的结构特点确定流量系数;三角闸门启闭力除按规范公式计算外还应考虑门体缝隙流和惯性阻力矩的影响。     

澜沧江航道建设工程溪口滩航道整治方案

以澜沧江Ⅳ级航道建设工程溪口滩航道整治为依托,针对溪口滩整治过程中需要提升航道等级、维持航槽稳定的问题,从溪口滩水沙运动规律、历史整治情况、来水来石特征等方面分析不同溪口滩险形成原因,提出修建拦石坝、溪口导流坝以及常年维护疏浚等治理措施,以达到提升航道尺度并维持航道稳定的目的。结果表明,在山区河流溪口滩航道整治过程中采用拦、导、疏等工程措施,能够解决溪口滩险碍航成滩的难题,可为类似工程提供参考。     

带缆水下机器人控制仿真模拟与水动力分析

本文以Fluent多重滑移网格技术对带缆水下机器人系统进行路径跟踪的仿真计算,将收放缆反馈控制与PID算法调节螺旋桨转速的双重控制策略应用于带缆水下机器人系统,并对带缆水下机器人系统升沉运动的控制误差、螺旋桨推力与转速之间的关系、缆绳系统的张力特性以及水下机器人的水动力响应做了分析。文中数值模拟结果表明,双重控制策略下,带缆水下机器人路径跟踪的控制运动较为精确,其升沉运动位移最大误差约为0.2 m;螺旋桨的转速与推力呈正相关性,转速越大,推力也越大;水下机器人沿预定轨迹运动过程中,缆绳系统张力呈现周期性震荡的变化规律,机器人主体受到的水动力荷载与多种因素相关。     

凿岩台车臂定位系统与液压臂结构不匹配问题研究

为解决凿岩台车臂定位系统与液压臂结构不匹配而出现液压臂下降时抖动、平动速度慢、泵压过高等问题,系统分析液压臂下降时抖动的原因,指出液压臂下降时抖动是由于液压臂下部液压缸平衡阀的先导油源压力不稳引起的,并通过试验证实,如果下降过程中下部液压缸平衡阀的先导油源压力一直大于其开启压力,液压臂能够平缓下降。可以通过提高液压臂油源压力和增大下部液压缸回油背压来解决液压臂下降抖动问题。