预应力高强混凝土梁极限承载力分析

针对高强混凝土材料力学行为的特殊性，考虑材料非线性的影响，通过将普通钢筋均匀“涂抹”于混凝土中，建立综合本构关系矩阵，将由此形成的普通钢筋与混凝土匀质材料整体离散为实体单元，并将预应力钢筋离散为独立的一维单元，用有限元法对预应力高强混凝土T型梁进行了极限承载力分析研究，给出了梁受力全过程矿．厂曲线，分析了其受力变形和破坏特点。为方便结构工程师参考，还对影响预应力高强混凝土梁极限承载力的主要结构参数（配筋率、高跨比等）进行了分析计算，推荐了这些参数的合理取值范围。     

珠江口海底隧道盾构法施工方案可行性分析

盾构法已经在国内外的地下工程中被广泛运用,特别是国外一些著名的海底盾构隧道,如英吉利海峡隧道、日本东京湾海底公路隧道、荷兰W esterschelde隧道;国内盾构技术也发展迅速,先后建成上海大连路、复兴东路过江盾构隧道,还有在建的上海翔殷路越江公路隧道、上中路隧道和已经开工建设的武汉、南京、上海长江桥隧工程等。这些海底、江底隧道的修建为盾构隧道的发展积累了丰富的经验。文章首先论述了国内外大直径、高水压、长距离推进等盾构施工关键技术,并结合珠江口海底隧道的建设条件与国内外的施工成功实例,对海底隧道盾构法施工方案的可行性进行了初步研究。     

Dual extended Kalman filter for vehicle state and parameter estimation

The article demonstrates the implementation of a model-based vehicle estimator, which can be used for combined estimation of vehicle states and parameters. The estimator is realised using the dual extended Kalman filter (DEKF) technique, which makes use of two Kalman filters running in parallel, thus 'splitting' the state and parameter estimation problems. Note that the two problems cannot be entirely separated due to their inherent interdependencies. This technique provides several advantages, such as the possibility to switch off the parameter estimator, once a sufficiently good set of estimates has been obtained. The estimator is based on a four-wheel vehicle model with four degrees of freedom, which accommodates the dominant modes only, and is designed to make use of several interchangeable tyre models. The paper demonstrates the appropriateness of the DEKF. Results to date indicate that this is an effective approach, which is considered to be of potential benefit to the automotive industry.     

主跨138m预应力混凝土连续梁桥的施工控制

本文以广州市金沙洲大桥主桥大跨度预应力混凝土连续梁桥为背景 ,介绍大跨度混凝土连续梁桥施工控制的目的、内容、方法和措施等 ,并根据现场测试的结果来验证本文所使用的控制方法的正确性和合理性     

陕西省路面设计参数研究

本研究根据陕西省地形特征，通过大量的室内试验及现场测试，按照陕西省二级公路自然区划，提出了路基土回弹模量建议值。并对陕西省常用的半刚性材料力学性能进行了分析研究，给出了半刚性材料及沥青混合料的设计参数推荐值。     

自适应指数平滑模型预测区域经济研究

三次指数平滑法预测区域经济时，平滑参数为一常量，这与实际不符，容易使预测结果误差偏大，甚至严重失真。本文在深入剖析指数平滑模型缺陷的基础上，对其进行改进，建立了自适应指数平滑模型。实践证明，该模型能够更好地反映区域经济发展的动态特性，提高预测的精度。     

Fatigue damage calculation for oil tanker and container ship structures

The fatigue behaviour of longitudinal stiffeners of oil tankers and container ships, subjected to dynamic loads, is analysed. The following dynamic load components are considered: hull girder vertical wave bending moment, alone and combined with the horizontal wave bending moment, hydrodynamic pressure and inertial forces caused by cargo acceleration.

The spectral method was selected to calculate the fatigue damage, based on S—N curves and Miner's rule. Following this approach, the fatigue damage may be calculated as a function of a stress parameter Ω_p, which represents the cumulative effect of wave induced loads in the unit of time and incorporates the combined effects of stress level and its occurring frequency.

Simple formulas for Ω_p of oil tankers and container ships are given, obtained from the results of hydrodynamic analyses performed on several ships, in different wave environments.

Several examples show the applicability of the methods to real ship structures. The method, however, still needs to be calibrated because of the simplifying hypotheses introduced in the loading conditions.     

砂卵石地层台阶法施工隧道围岩-支护结构应力应变特性三维离散元分析

为了解砂卵石地层隧道围岩和支护结构的应力应变特性，以青海循隆高速公伯峡隧道为依托，借助PFC3D离散元软件对公伯峡隧道穿越砂卵石地层进行三维模拟，重点研究以密排短管棚预支护为根本前提，以三台阶预留核心土为施工方法的砂卵石地层围岩和支护结构的应力应变特性，并与现场实测进行对比分析。研究结果表明： 隧道台阶开挖时，围岩应力集中范围逐渐从拱顶过渡到拱腰，直到拱脚，对应的塑性区范围不断扩大，且密排短管棚对塑性区的发展有一定的“遮拦效应”； 围岩横纵向变形规律一致，主要是向隧道临空面产生收敛变形，且密排短管棚形成的梁拱效应限制了掌子面前方位移发展； 2种方法得到的初期支护变形规律一致，均呈阶段性变化，拱顶下沉累计值大于周边收敛累计值，且两者的最终变形量均满足规范限值要求。     

城市交通能耗区的识别及等级划分方法研究

随着社会经济的发展，机动车保有量急剧增长，城市化过程中交通拥堵问题日趋严重，交通能源消耗加剧。为了降低由此带来的损失，需要及时探明路网中交通效率低、能耗高的区域，并采取有效的交通管理措施。通过研究交通状态与能耗的关系，进行相应的交通参数分析，建立能耗区识别及等级划分模型，计算得到3个等级能耗区的界定阈值分别为0．411和0．678。     

Technical Note: Force Control in Electrohydraulic Active Suspensions Revisited

The inner loop control for the actuator force can be quite simply compensated by means of a correction term to the desired force signal at the input. The correction requires only a measurement of the actuator piston velocity and is employed to cancel the loop disturbance caused by the oil flow to the actuator. Although an additional time constant is introduced by the integration in the inner loop force control, the overall performance is nevertheless quite close to that of an ideal optimal system.