Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Model Test on Grouting Law in Dynamic Water-Rich Sand Layers by the Electric Resistance Method北大核心CSCD

In order to study the diffusion law of grouting slurry in the water-rich sand layer under flowing water conditions, a grouting test model consisting of a main test system, a grouting system, and a measurement system was developed. And for detecting the diffusion scope of the grouts, a new resistivity method was proposed. It is found that the relationship between grouting pressure and grouting rate during the test is strong. Under hydrodynamic conditions, the grouting slurry diffuses elliptically. Due to gravity and the effect of the upper water flow, the center of gravity of the ellipsoid is below the grouting outlet, and the grouting effectively improves the physical and mechanical properties of water-rich sand bodies. At the same time, the resistivity method has a good application effect on the detection of grouting diffusion range. The range of slurry diffusion obtained by the resistivity method is basically consistent with the boundary of the stone body after excavation, indicating that the resistivity method is reliable for detection of grouting range in dynamic water-rich sand layer. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

海底柔性管道技术研究

随着海洋油气勘探开发的发展,柔性管道得到越来越广泛的应用。文中介绍了柔性管道的分类及结构,重点描述了粘结和无粘结柔性管道,无粘结柔性管道是目前国外发展趋势和研究重点。阐述了柔性管道的技术优势以及适用范围,同时介绍了柔性管道的发展状况、设计准则以及国外的主要制造厂商。国内柔性管道技术与世界先进水平之间还存在较大的差距,采用无粘结技术以及适用超深水环境将是国内未来深水海底柔性管道技术发展的方向。     

轴对称解对隧道衬砌水压力计算的适用性研究

文章根据渗流理论推导了隧道衬砌水压力的轴对称解,并利用数值分析方法研究了轴对称解对不同形状隧道断面与浅埋隧道的适用性.研究结果表明:轴对称解适用于非圆形隧道断面衬砌水压力的估算;隧道断面形状对衬砌水压力折减系数的影响较小,可以忽略不计,其影响大小主要由衬砌与围岩的渗透系数比值决定.对于浅埋低水头隧道,用轴对称解计算的毛洞流量Qm与数值解比较,其误差较大,最大误差为36.5％;但用来计算衬砌水压力p1以及衬砌后水流量Q1时,误差相对较小,最大误差为6.3％,特别是利用轴对称解得出的衬砌水压力值与利用数值解得出的衬砌水压力特征值最大误差仅为3.4％.     

基于Bayes判别分析方法的叙岭关隧道溶洞水源识别

基于Bayes判别方法,选取水化学常量组分作为判别指标,利用叙岭关隧道地区9个动态监测点的53个水样样本建立了该地区的水源判别模型.模型检验结果表明,其回判准确率为96.23％,具有较高的识别精度和工程推广能力.利用建立的判别模型,对叙岭关隧道1号溶洞内两个出水点RQ1和RQ2的水源进行了识别,并结合其流量动态变化特征、同位素分析结果,以及1号溶洞发育位置,推断1号溶洞内两个出水点的水源为P1m+q含水层中的岩溶地下水.根据判别结果,建议1号溶洞采取“以排为主”的原则加以处治,并尽量保留溶洞水的过水通道.     

汽车排放污染及净化对策研究

阐述汽车排放污染物的成分及其危害,介绍新排放法规Ⅰ型、Ⅲ型、Ⅳ型试验限值,重点分析汽车的5项排放影响因素及其净化措施。     

关于《钢质内河船舶建造规范》(2009)总纵强度问题的探讨

本文简要阐述了影响船舶总纵强度的主要因素,并对《钢质内河船舶建造规范》（2009）中将船舯剖面处的最小剖面模数表示成型深D的表达形式提出了自己的见解,并指出了总纵弯矩与中剖面最小剖面模数计算公式中的不协调。     

一种单片机控制的水温测试系统

由于现代多样的电子控制技术和电子控制理论的迅猛发展,高精度的机械在各类工业控制系统、生产线等方面的需求越来越大.其中以单片机为核心实现的数字控制器,因其体积小、简便易行等优点,而被广泛应用于各行各业.本文将单片机的温度控制系统作为设计核心,通过温度传感器、单片机等软件系统图,并利用软件编程,从而达到实现水温控制的目的....     

渤中稠油乳状液的流变性实验研究

此项研究的目的在于揭示含水率、压力和温度等对稠油乳状液流变特性的影响.实验结果表明,油品乳状液的反相点大约在含水率70%左右,温度对乳状液黏度和流变性影响较为明显,压力对乳状液黏度和流变性影响不大.     

移动式损管训练舱堵漏水循环系统设计

文章通过3ds Max和AutoCAD软件设计出移动式损管训练舱堵漏水循环系统,在系统中完善了堵漏训练所需的配套设施,解决堵漏水的循环利用,使损管堵漏训练能满足海警官兵日常训练要求.