山区公路层间滑移破坏机理分析及对策研究

通过现场调查,初步分析了山区公路沥青路面基面层滑移的主要原因。应用有限元法,对基层和面层之间的剪应力进行计算分析,得出了基面层间剪应力变化的一般规律,认为层间最大剪应力主要取决于面层厚度和荷载条件。在前述计算分析的基础上,利用自行研制的DLG A路面材料剪切仪进行了大量的层间滑移室内模拟试验,考察了不同的层间处理措施、温度、基层类型等因素对层间抗剪能力的影响,提出了防止基面层滑移的技术措施。     

Definition of wind blowers for vehicles testing at chassis-dyno facilities using a CFD approach

The need to increase measurement accuracy of fuel consumption and pollutant emissions in vehicles is forcing the market to develop chassis-dyno test cells that reproduce on-road conditions realistically.Air-cooling is key to vehicle performance. It is therefore critical that the design of a test cell guarantees realistic cooling of all vehicle components, as important errors in fuel consumption and emissions measurements may otherwise arise. In a test-room, a blower placed in front of the vehicle supplies the cooling air. While there are some guidelines in the literature for the selection of fans required for emissions measurements for standard driving cycles, the information for designing the air supply system for specific tests in other areas is scarce.New Real Driving Emissions (RDE) legislation will force manufacturers to perform on-road measurements of pollutants. This represents a significant challenge due to the variability of conditions coming from non-controlled parameters. In order to optimize vehicles, different tests are performed in cells equipped with a chassis-dyno where the on-road flow field around the vehicle is reproduced as closely as possible.This work provides some guidelines for the definition of the airflow supply system of chassis-dyno facilities for vehicle optimization tests, based on a CFD analysis of the flow characteristics around the vehicle. By comparison with the solution obtained for a vehicle in real road driving conditions, the exit section of the blower and the distance between the blower exit and the car that best reproduce realistic on-road flow conditions in a test room are determined.     

缓波型非粘接柔性立管的干涉敏感性

针对非粘接柔性立管在波浪和海流作用下易发生立管干涉的问题,以我国南海某油田输油立管和相邻锚链为例,分别对拖曳力系数、管道单位长度质量、外径、内部介质密度、立管抗拉弯扭刚度和悬挂角度等参数进行敏感性分析,得出不同参数的敏感性情况,并在此基础上提出一些建议供实际工程设计参考.     

隧道爆炸冲击波的危害及控制措施

目前山岭隧道施工基本以钻爆法为主,爆破过程中产生的冲击波会对隧道内的人员及机械设备安全产生较大影响,造成重大安全事故和财产损失。本文主要介绍了冲击波在隧道内传播会形成超压,且随着传播距离增加超压峰值逐渐衰减到大气压范围内;基于超压准则评估了冲击波对人体、隧道内设施及周边建筑物的危害程度;通过在隧道内安装简易的冲击波缓冲装置及加强监测、设置安全警戒线等控制措施,减弱了爆破冲击波的危害,从而达到安全快速施工的目的。     

高速铁路轨道的波阻抗及影响因素研究

高速铁路轨道在雷击或故障冲击电流作用下会产生暂态冲击过电压,该过电压的大小由轨道的波阻抗决定。通过建立高速铁路线路的仿真模型,分析直角冲击波在轨道上的传播与折反射过程,提出轨道的波阻抗的计算方法,研究钢轨类型、土壤电阻率、钢轨对地过渡电阻对波阻抗的影响。结果表明:P60型轨道波阻抗数值为235. 55Ω;轨道的波阻抗主要受钢轨类型和土壤电阻率的影响,高速铁路轨道的波阻抗在在210～250Ω变化;在高速铁路轨道仿真模型中,线路末端电阻等于波阻抗时,可以有效地消除折反射对仿真结果的影响,末端电阻的取值不需要考虑钢轨地过渡电阻的影响。研究给出高速铁路轨道波阻抗的范围及仿真模型中末端电阻的取值方法,可以为轨道过电压计算、分析与仿真提供理论与方法参考。     

Estimation of extreme significant wave heights and the associated uncertainties: A case study using NORA10 hindcast data for the Barents Sea

The reliability of an offshore structure is dependent on its response to the extreme wave climate; therefore, an adequate knowledge of the wave climate at a location is a prerequisite during design as well as in marine operations. This study aims to contribute to the knowledge of the extreme wave climate in the Norwegian Sector of the Barents Sea, using wave hindcast datasets from the Norwegian Reanalysis 10 km (NORA10) database for four locations.We have considered three commonly used methods for the estimation of extreme wave heights, that is, the initial distribution method, the peak over threshold method, and the annual maxima method. The parametric bootstrap concept is considered in the estimation of the epistemic uncertainty related to sample size. The estimated 100-year significant wave heights obtained from the three methods differ, and the degree of variability in the estimates varies, depending on the dataset. The epistemic uncertainty due to sample size is wider when considering the annual maxima method.The estimates obtained from the three methods show the importance of considering different methods and their associated uncertainties when estimating extreme wave values for design. While it is difficult to single out the best method among the three, the estimated values give knowledge of the possible range of the extreme significant wave heights at the locations. Generally, the datasets considered in this study suggest that the wave climate is less harsh further north compared to the southern region of the Barents Sea. The datasets do not suggest any temporal trends in the historical significant wave heights at any of the locations.     

基于隧道检测钢筋分布不均状况下判定衬砌结构安全性应用研究

近年来隧道内出现的越来越多的质量安全事故,引起各方高度重视,相应的最适宜隧道主体工程衬砌质量控制的地质雷达无损检测方法被广泛应用。通过雷达无损检测可揭露出衬砌内欠厚、脱空、钢筋分布不均等大量各类型缺陷,针对欠厚脱空等缺陷制定的注浆或开窗等治理措施是目前工程中常见的整改闭合工序,但钢筋分布不均对结构安全影响如何判定,怎么界定处理尚无成熟方案与规定。本文针对隧道项目中实际检测出的钢筋分布不均缺陷,在不宜大范围扰动结构及围岩进行整治的情况下,以及在避免其他问题共存等不利因素的前提下,应用有限元数值模拟计算分析强度安全系数,并结合现场外观等综合因素对衬砌结构安全性进行分析判定研究。     

关于公交停靠站影响区范围的研究

随着城市公共交通系统的发展,公交停靠站对道路交通流的影响已逐渐引起人们的注意。分析公交停靠站的影响首先应该对停靠站的影响区范围进行界定。在分析前人研究成果的基础上,基于交通波理论,按考虑超车与否,分析公交停靠站的影响区范围长度,得到不同交通流密度条件下公交停靠站影响区长度的计算公式。     

浮摆式波浪发电平台系泊系统设计

针对一台自行设计的浮摆式波浪发电平台的运动特点与采能方式,对其系泊系统进行设计。系泊型式为"平台—连接缆—浮筒—锚链—锚"的悬链线单点浮筒系泊。以试验海域海况参数为依据,计算系统载荷,并采用准静力分析法对系泊系统各构件进行选型设计。设计的连接缆为钢丝绳,浮筒为圆柱型钢制浮筒,锚链为二级有档锚链,作业锚为AC-14锚。经检验,设计的系统符合安全要求和平台稳定性需求。     

田湾核电站扩建工程取水明渠导流堤优化设计

取水工程为核电厂重要构筑物,按照较高的核电标准设计往往断面较大,在保证取水安全的前提下,分析不同工程的使用要求,有针对性的的进行优化设计,可降低工程造价。以田湾核电取水工程为例,分析优化设计过程,供类似工程参考。