HX_D1C型机车抱轴箱组装工艺难点及解决方案

文章介绍了HXD1C型大功率电力机车抱轴箱组装的结构形式,详细分析了抱轴箱组装的工艺难点,并针对工艺难点提出了解决方案,以利于抱轴箱工艺的执行,对机车今后大修以及其它车型抱轴箱组装提供参考。     

Methods to reduce dimensionality and identify candidate solutions in multi-objective signal timing problems

Adjusting traffic signal timings is a practical way for agencies to manage urban traffic without the need for significant infrastructure investments. Signal timings are generally selected to minimize the total control delay vehicles experience at an intersection, particularly when the intersection is isolated or undersaturated. However, in practice, there are many other potential objectives that might be considered in signal timing design, including: total passenger delay, pedestrian delays, delay inequity among competing movements, total number of stopping maneuvers, among others. These objectives do not tend to share the same relationships with signal timing plans and some of these objectives may be in direct conflict. The research proposes the use of a new multi-objective optimization (MOO) visualization technique—the mosaic plot—to easily quantify and identify significant tradeoffs between competing objectives using the set of Pareto optimal solutions that are normally provided by MOO algorithms. Using this tool, methods are also proposed to identify and remove potentially redundant or unnecessary objectives that do not have any significant tradeoffs with others in an effort to reduce problem dimensionality. Since MOO procedures will still be needed if more than one objective remains and MOO algorithms generally provide a set of candidate solutions instead of a single final solution, two methods are proposed to rank the set of Pareto optimal solutions based on how well they balance between the competing objectives to provide a final recommendation. These methods rely on converting the objectives to dimensionless values based on the optimal value for each specific objectives, which allows for direct comparison between and weighting of each. The proposed methods are demonstrated using a simple numerical example of an undersaturated intersection where all objectives can be analytically obtained. However, they can be readily applied to other signal timing problems where objectives can be obtained using simulation outputs to help identify the signal timing plan that provides the most reasonable tradeoff between competing objectives.     

导管式推进器非定常性能数值计算方法研究

基于滑移网格方法，采用SST k-ω湍流模型研究不同网格划分方式对带前置定子导管式推进器非定常性能的研究。首先基于相对参考坐标系法及滑移网格方法分别对推进器在定常与非定常下的性能进行数值预报，并与试验结果相比验证计算方法的可靠性。基于该方法研究整体网格划分方式与周期性网格对推力系数、扭矩系数与推进器各个方向上的非定常脉动力的影响。研究结果为进一步研究推进器非定常性能提供了参考。     

泥泵水力性能动态特征的数值模拟分析

在使用滑移网格模拟分析新设计的HDP-263-50-130-4型泥泵时,发现叶轮处于不同位置时,同一转速和流量下,泥泵的扬程、扭矩、效率均呈周期性的波动,该波动近似于正弦函数,各量波动幅度较大,波动周期等于叶轮转过两相邻叶片的夹角所需的时间 对于该型号泵,扬程的波动要领先力矩约0.21个波动周期,效率的波动领先力矩约0.34个波动周期;当叶轮的一个叶片转过蜗壳的第Ⅰ断面,且与此断面呈16.左右夹角时,泥泵达到最高效率,约为92％;当叶轮的一个叶片转向蜗壳的第Ⅰ断面且与其夹角约为29°时,泥泵效率最低,约为77％.经分析认为,泥泵水力性能波动的主因是运动叶轮与静止蜗壳之间的动静干扰,该干扰主要体现在叶轮相对涡舌的位置的变化引起涡舌周围流态的变化.     

贮存系统的联合维修策略

为了保证贮存系统的可用性,需要对其故障与否进行检测,针对该问题提出了包含定期检查和预先更换的维修策略。为了协调部件更换和备件供应,联合考虑了连续检查的（0,1）订货策略,所以联合维修策略包括维修策略和备件供应策略。基于联合策略建立了一个规划模型,在满足可用度约束条件下最小化平均总费用。基于更新过程,推导了贮存系统服从一般寿命分布的性能指标。以威布尔寿命分布为例,结果表明联合策略比独立策略更有效。     

大跨度预应力混凝土斜拉桥基于定期检测的损伤识别方法

为了在定期检测信息的基础上实现大跨度预应力混凝土斜拉桥的健康状态评估,提出采用无线多点自动综合测试系统监测结构应力,利用环境随机振动法测试全桥索力,并结合桥梁几何测试信息,获得桥梁状态的综合检测方法。针对招宝山大桥,建立最优化遗传静力反分析模型,采用基于遗传算法的大型复杂结构损伤识别程序对模拟的损伤工况进行分析,有效识别出了斜拉桥主梁的损伤位置。并且由于遗传优化算法对参数的类型和数量没有限制,对斜拉桥进行包含不同损伤类型的参数化建模,可以进行结构多类型损伤的识别,因此,可推广至其他复杂桥梁的损伤识别,为同类工程所借鉴。     

铈锆氧化物固溶体制备方法的比较研究

分别采用均匀沉淀法和共沉淀法制备了铈锆氧化物固溶体,研究了制备方法对铈锆氧化物固溶体的晶体结构、比表面积以及储氧能力的影响。结果表明,均匀沉淀法制备的铈锆氧化物固溶体的比表面积小,储氧能力较强,所制得的三效催化剂具有良好的催化活性,但该方法所制备的铈锆氧化物固溶体耐高温性能较差。     

竖向荷载作用于半无限体内部时的粘弹性解

建筑物的持续沉降,特别是软土地区的建筑物基础沉降通常与地基土的流变性密切相关。考虑地基土的粘弹性特征,系统研究了空间半无限体内部作用集中力时的粘弹性解。研究假定半无限体为线性粘弹性介质,半无限体在内部集中力作用下的应力状态为三维应力状态,应力球张量和应变球张量之间符合弹性关系,而应力偏张量和应变偏张量之间符合Kevin固体粘弹性应力应变关系。利用半空间体内部受竖向集中力的Mindlin弹性解,根据准静态弹性-弹粘性对应原理,在相同荷载条件下,首先对弹性解进行Laplace变换,然后将弹性解中的物理参数用线性粘弹性理论中经过Laplace变换的物理参数来替代,最后再进行Laplace逆变换,求得位移、应力粘弹性解答。作为解答的应用,给出了粘弹性半无限空间体内部矩形面积上作用有竖向均布荷载、三角形分布荷载时的粘弹性沉降计算公式。解答的退化验证表明,该粘弹性解答是正确的,所得到的解答对工程实践具有一定的意义。     

Propagating buckles in corroded pipelines

Rigid–plastic solutions for the steady-state, quasi-static buckle propagation pressure in corroded pipelines are derived and compared to finite element predictions (ABAQUS). The corroded pipeline is modeled as an infinitely long, cylindrical shell with a section of reduced thickness that is used to describe the corrosion. A five plastic hinge mechanism is used to describe plastic collapse of the corroded pipeline. Closed-form expressions are given for the buckle propagation pressure as a function of the amount of corrosion in an X77 steel pipeline. Buckles that propagate down the pipeline are caused by either global or snap-through buckling, depending on the amount of corrosion. Global buckling occurs when the angular extent of the corrosion is greater than 90°. When the angular extent is less than 90° and the corrosion is severe, snap-through buckling takes place. The buckle propagation pressure and the corresponding collapse modes also compare well to finite element predictions.     

肋骨非均匀排列的圆柱壳振动特性研究

研究了肋骨非均匀排列对加肋圆柱壳振动特性的影响。首先,以安德森定域效应的原理为基础,肋骨间距为随机分布,分析了肋骨非均匀排列时圆柱壳的振动特性,然后,采用两种肋骨间距,交替排列,构造整个圆柱壳的肋骨不等间距排列形式,两种肋骨间距的确定方法是:保持两种肋骨间距的总和不变,逐步增大两者的间距差,从而增加相邻的肋骨间的两个圆环结构的固有频率差,直至固有频率差趋于不变,最终确定了两种肋骨间距。分别计算并对比分析了肋骨等间距和不等间距排列的圆柱壳的均方振速,结果表明:肋骨不等间距排列具有一定的减振效果。