全文获取类型
收费全文 | 5721篇 |
免费 | 157篇 |
专业分类
公路运输 | 2443篇 |
综合类 | 1082篇 |
水路运输 | 1002篇 |
铁路运输 | 1242篇 |
综合运输 | 109篇 |
出版年
2024年 | 46篇 |
2023年 | 203篇 |
2022年 | 209篇 |
2021年 | 275篇 |
2020年 | 193篇 |
2019年 | 155篇 |
2018年 | 84篇 |
2017年 | 93篇 |
2016年 | 87篇 |
2015年 | 135篇 |
2014年 | 262篇 |
2013年 | 249篇 |
2012年 | 298篇 |
2011年 | 311篇 |
2010年 | 293篇 |
2009年 | 316篇 |
2008年 | 285篇 |
2007年 | 241篇 |
2006年 | 225篇 |
2005年 | 181篇 |
2004年 | 191篇 |
2003年 | 182篇 |
2002年 | 153篇 |
2001年 | 115篇 |
2000年 | 137篇 |
1999年 | 115篇 |
1998年 | 102篇 |
1997年 | 102篇 |
1996年 | 112篇 |
1995年 | 100篇 |
1994年 | 79篇 |
1993年 | 76篇 |
1992年 | 91篇 |
1991年 | 61篇 |
1990年 | 59篇 |
1989年 | 50篇 |
1988年 | 9篇 |
1986年 | 1篇 |
1965年 | 2篇 |
排序方式: 共有5878条查询结果,搜索用时 390 毫秒
531.
532.
533.
秦沉线结合梁全焊Ⅰ型梁疲劳试验研究 总被引:1,自引:1,他引:0
秦沈客运专线有14座钢-混凝土结合梁,钢梁截面有箱梁和Ⅰ型板梁两种,其中在24m 32 24m连续梁的Ⅰ型钢板梁中首次采用了工地全断面焊接技术,针对其现场焊,手工焊和厚板对焊接这3个技术难点,重点对Ⅰ型梁单面开坡口,全断面对接焊细节进行了疲劳试验研究,并对断口的起裂原因予以分析,从而得到可靠的试验数据,据此对相应焊接工艺提出质量要求,为掌握单面开坡口对接焊细节的受力状态,文章通过计算机模拟现场施工可能发生的对接错位,分析揭示了其对构件受力的不利影响程度,提出了相应的改进措施,研究结果表明,所选择的焊接工艺及加工的试验能够满足秦沈线Ⅰ型梁全断面对接焊的疲劳设计要求。 相似文献
534.
535.
536.
537.
宁波329国道北仑至三山线公路工程区内断裂遥感研究 总被引:3,自引:0,他引:3
结合一个具体的工程项目,就遥感技术应用于公路工程地质勘察时的技术路线、技术方法进行了阐述,并重点介绍了工程区内断裂的研究结果,对工程的设计与施工提出了建议。 相似文献
538.
539.
LI Qing-fen WANG Peng REN Zheng-yi and LONG Ping School of Mechanical & Electrical Engineering Harbin Engineering University Harbin China 《船舶与海洋工程学报》2003,2(2):1-4
In this paper, the effect of plastic constraint on the initiation of ductile tears in four different shipbuilding structural steels has been experimentally studied by measuring the J-integral and crack opening displacement COD at initiation in three-point bend specimens with deep and shallow notches. Experimental results of seven groups of different strength alloy steels show that both Si and Ji values of ductile tear from the shallow crack specimens which have less constraint flow field are significantly higher than those of deeply notched specimens. Slip-line-field analysis shows that, for shallow crack, the hydrostatic stress is lower than that from standard deeply cracked bend specimen, which develops a high level of crack tip constraint, provides a lower bound estimate of toughness, and will ensure an unduly conservative approach when applied to structural defects, especially if initiation values of COD and J-integral are used. 相似文献
540.
1 引言铁路货车是完成铁路货物运输任务的运载工具,轮对和轴承是保证货车安全运行的关键部件。由于车轴在旋转的工况下长期承受交变载荷的作用,其应力集中部位的圆周表面均有产生疲劳裂纹的可能,在车轴上,轴颈卸荷槽部位是车轴的关键部位,如果加工质量或表面粗糙度达不到有关技术要求,容易造成应力集中产生疲劳裂纹,降低其防腐蚀能力,减少车轴寿命,甚至影响行车安全。提高和稳定轴颈部位加工质量是防止车轴轴颈产生疲劳裂纹的有效方法。 2 RD2车轴轴颈卸荷槽加工现状目前车轴轴颈卸荷槽部位加工多采用车削加工,轴颈采用磨削;少部分加工单位采用了成型磨床设备,取消了卸荷槽,较大幅度的提高了轴颈的抗疲劳强度,提高了车轴运用的可靠性。根据目前采用的 GB/T12814-2002- 07标准车轴图样,图1为 RD2车轴图样,图中圆圈部分为卸荷槽、防尘板座部 相似文献