汽车噪声控制技术的最新进展与发展趋势

对汽车噪声控制技术领域的最新进展及发展趋势进行综述,包括噪声控制技术在汽车新产品设计中的应用(整车级别的声学品质目标设定、系统和元件级别的声振特性目标设定)、NVH仿真分析的置信度、NVH虚拟环境技术、车辆噪声控制的材料及结构技术等相关主题。     

存在车辆干扰的车道线识别

为避免道路上行驶的其它车辆对车道线识别的干扰,提出了一种结合车辆识别的车道线识别方法。融合雷达数据,车辆识别模块首先在图像中识别出车辆占据的区域;对于每一个车道线识别模块挑出的车道线候选点进行判断,去除处于车辆区域的车道线点;如果有效车道线点数目不足,则利用卡尔曼滤波的跟踪结果,确定符合最小风险函数的车道线位置。经过多种工况下的试验验证,该方法能够稳定地对车道线进行识别,准确地提取车道线参数,并且算法对车辆干扰有良好的抵抗能力。     

汽车驾驶员行为模式及其心理因素对可靠性的影响

综述了汽车驾驶员行为的三种典型模式，详细地剖析了汽车人机系统中驾驶员的行为特征，建立了驾驶员行为模式，并推导出计算驾驶员失误率的公式。应用交通心理学的基本观点，根据驾驶员失误的心理指标体系，结合实际交通事故案例分析，阐明了心理因素对驾驶员可靠性的影响及其程度。     

汽车碰撞台车模拟试验吸能器的研究

介绍一种钢筋阻尼吸能器,经过理论计算,该吸能装置可通过调节钢筋的种类、数量、长度和放置方式,复现不同车型、不同碰撞车速条件下的车身减速度波形,可广泛用于汽车安全部件的开发及试验验证。     

石方边坡控制爆破在公路路网工程中的运用

文章通过光面爆破与普通石方爆破的对比,总结石灰岩地区光面爆破各技术参数的选取和施工工艺的控制方法。     

Dual extended Kalman filter for vehicle state and parameter estimation

The article demonstrates the implementation of a model-based vehicle estimator, which can be used for combined estimation of vehicle states and parameters. The estimator is realised using the dual extended Kalman filter (DEKF) technique, which makes use of two Kalman filters running in parallel, thus 'splitting' the state and parameter estimation problems. Note that the two problems cannot be entirely separated due to their inherent interdependencies. This technique provides several advantages, such as the possibility to switch off the parameter estimator, once a sufficiently good set of estimates has been obtained. The estimator is based on a four-wheel vehicle model with four degrees of freedom, which accommodates the dominant modes only, and is designed to make use of several interchangeable tyre models. The paper demonstrates the appropriateness of the DEKF. Results to date indicate that this is an effective approach, which is considered to be of potential benefit to the automotive industry.     

Tractor-semitrailer model for vehicles carrying liquids

This article presents a model for solving solid-fluid interactions in vehicles carrying liquids. A tractor-semitrailer model is developed by incorporating suspension systems and tire dynamics. Owing to the solid-fluid interaction, equations of motion for the vehicle system are coupled. To simplify the complicated solution procedure, the coupled equations are solved separately using two different codes. Each code is analyzed separately; but as the parameters of the two codes depend on each other, the codes must be connected at the end of each time step. To determine the dynamic behavior of the system, different braking moments are applied. As the braking moments increase, braking time decreases. However, it turns out that increasing the braking moment to more than a certain level produces no significant results. It is also shown that vehicles carrying fluids need a greater amount of braking moments in comparison to vehicles carrying solids during braking. In addition, as the level of the fluid inside the tanker increases, from one-third to two-third of the tanker's volume, the sloshing forces applied to the tanker's walls increase. It was also concluded that the strategy used in this article to solve for the solid-fluid interaction by incorporating vehicle dynamic effects represents an effective method for determining the dynamic behavior of vehicles carrying fluids in other critical maneuvers.     

走-停巡航系统分层控制器设计

结合驾驶统计模型，设计了走一停自适应巡航系统的纵向车间距离控制器。上位控制器的设计与车辆模型无关。在建立目标性能函数的基础上得到控制律；而下位控制器则将油门和制动控制独立设计，依据一定的切换逻辑使它们分别作用于车辆。在制动控制的设计中引入了改进型史密斯预估器。在多种工况下的仿真试验中表明控制器性能良好。     

不同混合动力电动轿车方案的比较与分析

设计了同在离合器前与发动机的动力耦合的ISA并联、电机在离合器后变速器前与发动机的动力耦合的一般并联、类似于Prius的混联三种HEV方案。对这三种方案和原轿车的最高车速、原地起步加速特性等动力性指标和基于ECE＋EUDC的100km油耗和续驶里程等能量经济性指标及排施行性进行了仿真和分析。得到相应结论。     

车辆控制系统CAN总线通信的实施方法

本文采用SAE J1939通信协议在载货车上实施了CAN总线通信，采用Intel87C196CA单片机实现了它的硬件通信，采用J1939通信协议设计了ABS控制器和变速器控制器的各种数据的辨识位和它们之间的通信过程。