起重机风灾事故的防范

针对起重机所受风灾的类型,结合现场检测和实际应用情况,分析各种防风(即防阵风)防台(即防台风)设施的特点和用途,介绍上海港在研究设防等级、建立管理体系、采取具体防范措施等方面的经验。     

CAD／CAM技术在船舶减摇鳍设计制造中应用的思考

介绍了CAD／CAM技术以及如何应用CAD／CAM技术为减摇鳍的设计开发提供更有效的设计平台。     

基于灰理论的港口吞吐量预测研究

港口吞吐量是港口建设的重要依据,有效预测港口吞吐量,才能使港口在海洋运输业中发挥重要作用。灰理论预测可以在少量信息、不完全数据的情况下,揭示港口吞吐量的发展变化特征,是研究港口吞吐量的有效工具。本文对上海港货物吞吐量进行研究的结果表明,应用灰理论对港口吞吐量建立灰色模型GM(1,1)进行短期预测,其结果有较高的实用价值。     

Estimation of value of travel time reliability

In mode choice decision, travelers consider not only travel time but also reliability of its modes. In this paper, reliability was expressed in terms of standard deviation and maximum delay that were measured based on triangular distribution. In order to estimate value of time and value of reliability, the Multinomial and Nested Logit models were used. The analysis results revealed that reliability is an important factor affecting mode choice decisions. Elasticity is used to estimate the impacts of the different policies and system improvements for water transportation mode. Among these policies, decision maker can assess and select the best alternative by doing the benefit and cost analysis based on a new market share, the value of time, and the value of reliability. Finally, a set of promising policies and system improvement of the water transportation were proposed.     

全回转拖轮的阻力性能分析

论述全回转拖轮的阻力性能特点,通过船模试验结果验证全回转拖轮在自航状态时兴波阻力是总阻力中的主要成分,结合有关实船论述船舶主尺度、船型系数及线型对阻力性能的影响,阐明如何设计和建造阻力性能好的全回转拖轮。     

18 000 t化学品及成品油船设计和TC规则

18 000 t化学品及成品油船是江南造船集团为加拿大Algoma Control corporation公司建造的.入DNV船级社.挂加拿大旗.该文主要介绍了18 000 t化学品及成品油船的主要技术特点(主要技术参数、结构特点、舾装特点、防腐蚀、轮机特点、化学品和成品油船专用系统、电气特点、安全保障)和挂旗国加拿大TC规则(送审工作、要TC证书的材料和设备、有TC型式认可证书的国内产品、TC规则特殊要求、圣劳伦斯运河要求).     

A review of the Effect of α/W ratio on fracture toughness （Ⅱ） experimental investigation in LEFM

In part I of this series, experimental investigation in EPFM （elastic-plastic fracture mechanics） had been discussed. In this paper, experimental investigation in LEFM （ linear elastic fracture mechanics） is given. Fracture toughness tests had been carried out on three different strength steels, using both through-cracked specimens with different α/W ratio and semi-elliptical cracked specimens with variable crack size and shape. Results show that the fracture toughness KIC increases with decreasing α/W when α/W 〈 0.3 for three-point-bend specimens, and that for α/W 〉 0.3, it is independent of α/W. Shallow crack specimens, both through-cracked and surface-cracked, gave markedly higher values than deeply notched specimens. However, the effect of crack shape on fracture toughness is negligible. Results also show that the LEFM approach to fracture is not tenable for design stresses where αc is often very small, far less than 2.5 （ KIC/σy）^2.     

软件成本估算

成本管理是软件项目管理的主要内容之一，软件成本估算是项目成本管理的一个非常重要的部分。概述了常用的软件成本估算方法并比较了其优缺点，详细介绍了目前国际上广泛应用的由美国南加州大学软件工程研究中心提出的COCOMOⅡ成本估算模型。     

齿轮胶合临界温度的变化新规律

研究了临界温度随油品（添加剂）性能和速度的变化新规律，首先给出了确定临界温度的试验方法和反推公式；根据不同润滑方式的试验结果获得了临界的变化曲线。本将临界温度表示成龆一的二次函数，并发现油品性能高低和有无添加剂对临界温度绝对值大小有很大的影响；最后根据理论计算公式从数学上证明了临界温度存在低点速度的重要特征。