Mechanism of Tunnel Water Inflow Caused by Bending Failure of a Waterproof Dike Based on a Circular Thin Plate Mechanical Model北大核心CSCD

Water bursts during tunnel construction endanger construction, and it is therefore necessary to reserve a waterproof dike with the required thickness to avoid water bursts and to take reinforcement of the dike and treatment of the structure liable to trigger a water burst. Using the water burst at K5+398 of the Mingyueshan tunnel of the Shanghai-Chengdu expressway as an example, and considering the type of tunnel section and the upright mudstone of the dike, the waterproof dike at the work face is simplified as a round thin plate. A formula for the calculation of a minimum safety thickness for the critical waterproof dike is deduced by analyzing the force applied on the water-proof dike, and the minimum safety thickness for the water burst section at K5+398 of the Mingyueshan tunnel is cal-culated. The numerical simulation analysis demonstrates the critical thickness of waterproof dike at K5+398 of the Mingyueshan tunnel is 1.4-1.55 m, and the calculated water inflow and water burst basically agree with the actual condition. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Analysis on the Characteristics and Development Trends of the Support Technology of High Ground Stress Tunnels in China北大核心CSCD

Combining the present situation and development trend of different tunnel support technologies at home and abroad, this paper analyzes the problems of rockburst in hard rock tunnels and large deformation in soft rock tunnels caused by high ground stress. It is concluded that: 1) regarding the rockburst problem, the current support technology is mainly influenced by the rock burst mechanism which is dominated by static factors, and so the used support components are generally of smaller deformation performance and "passive support" properties; 2) as the rockburst is the result of dynamic-static stress coupling, and only the anchor bolt has the "active support" attribute in the current "shotcrete+anchor bolt+wire net" support system, so the best support system should have the two functions of active support and energy release in terms of the rockburst problem, and the key focus of the research and development is anchorage members; 3) there are three main support types for large deformation in soft rock tunnels, e.g. the heavy support, layered support and yielding support. Among them, the heavy support system in underground cavern with large deformation is easy to induce excessive surrounding rock pressure, and so the applicable conditions are limited. The layered support system is still not the best choice due to its immature theoretical study, difficult determination of the thickness value and the installation time of each support layer and the interference to construction progress. With the characteristics of timely support and yielding while supporting, the yielding support system can give full play to the performance values of surrounding rocks and supporting materials, and make both of them reach the optimal state, so it is the best choice for supporting the soft rock tunnels with large deformations. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Back-Calculation of Ground Stress Field and Rockburst Analysis for Wunvfeng Tunnel北大核心CSCD

Studying the in-situ stress distribution at a tunnel site is very important to determine surrounding rock characteristics, the engineering design and the construction scheme. By using the multiple linear regression method based on the least square algorithm, the initial geostress field is analyzed and the corresponding regression coefficients are obtained. The ground stress obtained from the proposed back analysis is reasonable and can meet the demands of the engineering applications. From the rockburst risk level distribution diagram, it is speculated that the Wunvfeng tunnel is in the high filed stress area. Field monitoring should be strengthened and emergency plans should be made to cope with the rockburst risks during the construction process. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

On Safety in Dismantling Temporary Strut of Super-large Tunnels with Double-layer Primary Support北大核心CSCD

More and more multiple-track tunnels and super-large section tunnels have been built, and disman- tling of temporary strut is a weak point of the whole structure during force transfer when the secondary lining is con- structed. It is significant to guarantee structure safety during dismantling of temporary strut. Little systematic re- search on safety in dismantling of temporary strut of the super-large section tunnel with double-layer primary support has been conducted, so the internal force and security of the two-layer primary support of the Xinkaotang tunnel were analyzed by a numerical analysis and site measurement, and it proves the effect of two-layer primary support on the safety during strut dismantling. The research results indicate that: (1) with constant support thickness and one-time longitudinal dismantling length, the safety factor of secondary primary support is larger than that of the first primary support, and the safety factor of the first primary support is larger than that of the single-layer primary support. Change range of safety factor for the first primary support is smaller than that of the single-layer primary support, and the safe factor for the single-layer primary support is smaller than that of the secondary primary support; (2) with the same support pattern, the safety factors increase firstly and then decrease with an increase of the onetime dismantling length. The calculated results of various cases show that the reasonable one-time dismantling length for this project is about 9 m. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Comparative Analysis of Calculation Methods for Jacking Force of Jacking Pipes北大核心CSCD

Jacking force is the most important parameter in jacking pipe engineering, and reasonable calculation of jacking forces plays an important role in safe and smooth pipe jacking construction. There are many calculation methods for pipe jacking force at present, and the calculation results may be affected to some extent by different cal⁃ culation methods. For this reason, calculation methods of jacking force (frictional resistance) were collected and a comparative analysis was conducted with aspects to the advantages, disadvantages and applicabilities. The results show that as for the jacking force calculated by empirical formulae, the soil layer classifications corresponding to giv⁃ en frictional force per unit area and relevant factors to be considered are different, and the values of frictional force per unit area between pipe and soil in the same soil layer are also different; as for the jacking force calculated by theo⁃ retical formulae, the calculation methods for vertical earth pressure at crown are different and much effected by the pipe buried depth; as for the jacking force calculated by numerical simulation, the selected theories for the simula⁃ tion program and the construction factors to be considered during simulation are different. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Experimental Study on Mechanical Behaviors of Prefabricated Column-Base Joint with Grouted Sleeves Connecting Longitudinal Reinforcements in Tunnels北大核心CSCD

In recent years, large shield tunnels with internal double-decked lanes have been developing rapidly in the field of highway tunnels, and prefabricated elements are increasingly adopted in internal structure. Based on the columns-base joint in Zhuguanglu tunnel, which is under construction, 2 full-scale specimens are designed for the quasi-static test, one specimen is connected with grout sleeve splicing and the other is cast in place. The test results show that: the bearing capacity of specimen with grout sleeve splicing is equal to that of cast-in-situ specimen, but its ductility and energy dissipation capacity are worse than that of the cast-in-situ specimen. And for the specimen with grout sleeve splicing, there exists crack concentration on the area above the sleeve. The crack width is too larger in this area. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

Soil Body Deformation Caused by Construction of a Double-Line Shield Tunnel with Multiple Factors北大核心CSCD

Considering the influence of many factors (soil loss, frontal additional thrust, the friction force of the shield shell and the additional grouting force), a method for improving the uniform soil body movement model is pro-posed, and a mechanical calculation model is established to study the calculation method for soil body deformation caused by double-line parallel shield driving. Based on the Mindlin solutions of elastic mechanics, the theoretical solutions for soil body deformations caused by the last three factors are calculated; considering the uniform soil body movement model, the theoretical solutions for soil body deformations caused by soil loss are calculated, then the to-tal theoretical solutions for soil body deformations under multiple factors are obtained by means of superposition. The vertical surface settlement, vertical horizontal displacement, and vertical displacements of the soil body at different depths of Hangzhou Metro Line 1 are calculated to analyze the variation laws. Meanwhile the influential factors for horizontal displacement variation are studied. The research shows that with a change of depth, the settlement of the soil body changes within the scope of 10 to 13 m in the horizontal direction near where the maximum settlement occurs;the direction of the horizontal displacement of the soil body changes with a change of the positional relationship be-tween the calculation points and the tunnel; and with an increase of interval J for the two tunnels, the horizontal dis-placement of the soil body of a deep double-line tunnel decreases while the displacement near the surface changes slightly. © 2018, Editorial Office of "Modern Tunnelling Technology". All right reserved.     

潮位对深海筑堤工程深层土体水平位移的影响

深海筑堤工程中必须对深层土体进行水平位移监测。自动化测斜技术每天能在固定时间自动监测传感器读数,如果设置监测间隔为48 min,即潮位隔天的推迟时间,则可以分析出潮位对深海筑堤工程中深层土体水平位移的影响。结合浙江某筑堤工程的自动化测斜随潮位变化的监测数据等,找出潮位对深海筑堤工程中深层土体水平位移的影响及规律,提出适用于类似工程的应用方法和案例。     

整体推进式桩基码头结构设计与施工

针对在拉美和非洲地区部分码头建设中,存在大型船机设备缺乏和长周期波较为明显、常规打桩船作业和预制构件安装困难的问题,基于一般桩基码头结构,在设计和施工两个方面进行优化,采用桩顶施工行走平台方法施工,利用桩基自身作为支撑结构,大量采用叠合式上部结构,实现将海上施工转化为陆上施工的创新,形成整体推进式桩基码头结构,规避大型船机设备缺乏和长周期波较为明显的问题,具有良好的经济性和对强震区的适应性。     

长江口深水航道治理工程不同阶段北槽丁坝群坝田泥沙冲淤分析

根据长江口深水航道治理工程不同阶段的地形分析,定量分析不同工程阶段影响下北槽丁坝群坝田冲淤厚度以及地形变化。结果表明:在不同的工程阶段,北槽南北侧坝田冲淤差异受工程进度影响,总体呈逐年淤积趋势,南北侧坝田呈"洪季多淤、枯季少淤积"的状态,北侧坝田淤积厚度大于南侧。北槽主槽与坝田地形变化在2010年之前变化较大,2010年之后,主槽基本趋于稳定,变化较缓,坝田则持续淤积。